Hitachi CP-WX1100 Bedienungsanleitung

Projector

CP-X10000/CP-WX11000/CP-SX12000

User's Manual – Operating Guide

Technical

Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode

720 x 400 37.9 85.0 VESA TEXT

640 x 480 31.5 59.9 VESA VGA (60Hz)

640 x 480 37.9 72.8 VESA VGA (72Hz)

640 x 480 37.5 75.0 VESA VGA (75Hz)

640 x 480 43.3 85.0 VESA VGA (85Hz)

800 x 600 35.2 56.3 VESA SVGA (56Hz)

800 x 600 37.9 60.3 VESA SVGA (60Hz)

800 x 600 48.1 72.2 VESA SVGA (72Hz)

800 x 600 46.9 75.0 VESA SVGA (75Hz)

800 x 600 53.7 85.1 VESA SVGA (85Hz)

832 x 624 49.7 74.5 Mac 16” mode

1024 x 768 48.4 60.0 VESA XGA (60Hz)

1024 x 768 56.5 70.1 VESA XGA (70Hz)

1024 x 768 60.0 75.0 VESA XGA (75Hz)

1024 x 768 68.7 85.0 VESA XGA (85Hz)

1152 x 864 67.5 75.0 VESA

1152 x 864 (75Hz)

1280 x 960 60.0 60.0 VESA

1280 x 960 (60Hz)

1280 x 1024 64.0 60.0 VESA SXGA (60Hz)

1280 x 1024 80.0 75.0 VESA SXGA (75Hz)

*1280 x 1024 91.2 85.0 VESA SXGA (85Hz)

*1600 x 1200 75.0 60.0 VESA UXGA (60Hz)

1280 x 768 47.7 60.0 VESA W-XGA (60Hz)

1400 x 1050 65.3 60.0 VESA SXGA+ (60Hz)

1280 x800 49.7 60.0 VESA 1280 x 800 (60Hz)

NOTE • Be sure to check jack type, signal level, timing and resolution

before connecting this projector to a computer.

• Some computers may have multiple display screen modes. Use of some of

these modes will not be possible with this projector.

• Depending on the input signal, full-size display may not be possible in some

cases. Refer to the number of display pixels above.

• Although the projector can display signals with resolution up to UXGA

(1600x1200), the signal will be converted to the projector’s panel resolution

before being displayed. The best display performance will be achieved if the

resolutions of the input signal and projector panel are identical.

• Automatic adjustment may not function correctly with some input signals.

• The image may not be displayed correctly when the input sync signal is a

composite sync or a sync on G.

• The HDMI input does not support the signals marked with *.

Example of computer signal

Initial set signals

The following signals are used for the initial settings. The signal timing of some

computer models may be different. In such case, adjust the items V POSITION

and H POSITION in the IMAGE menu.

Back porch (B) Front porch (D) Back porch (b) Front porch (d)

Display time (C) Display time (c)

Data Data

H. Sync. V. Sync.

Sync (A) Sync (a)

Computer/

Signal

Horizontal signal timing (μs) Computer/

Signal

Vertical signal timing (lines)

(A) (B) (C) (D) (a) (b) (c) (d)

TEXT 2.0 3.0 20.3 1.0 TEXT 3 42 400 1

VGA (60Hz) 3.8 1.9 25.4 0.6 VGA (60Hz) 2 33 480 10

VGA (72Hz) 1.3 4.1 20.3 0.8 VGA (72Hz) 3 28 480 9

VGA (75Hz) 2.0 3.8 20.3 0.5 VGA (75Hz) 3 16 480 1

VGA (85Hz) 1.6 2.2 17.8 1.6 VGA (85Hz) 3 25 480 1

SVGA (56Hz) 2.0 3.6 22.2 0.7 SVGA (56Hz) 2 22 600 1

SVGA (60Hz) 3.2 2.2 20.0 1.0 SVGA (60Hz) 4 23 600 1

SVGA (72Hz) 2.4 1.3 16.0 1.1 SVGA (72Hz) 6 23 600 37

SVGA (75Hz) 1.6 3.2 16.2 0.3 SVGA (75Hz) 3 21 600 1

SVGA (85Hz) 1.1 2.7 14.2 0.6 SVGA (85Hz) 3 27 600 1

Mac 16" mode 1.1 3.9 14.5 0.6 Mac 16" mode 3 39 624 1

XGA (60Hz) 2.1 2.5 15.8 0.4 XGA (60Hz) 6 29 768 3

XGA (70Hz) 1.8 1.9 13.7 0.3 XGA (70Hz) 6 29 768 3

XGA (75Hz) 1.2 2.2 13.0 0.2 XGA (75Hz) 3 28 768 1

XGA (85Hz) 1.0 2.2 10.8 0.5 XGA (85Hz) 3 36 768 1

1152 x 864

(75Hz) 1.2 2.4 10.7 0.6 1152 x 864

(75Hz) 3 32 864 1

1280 x 960

(60Hz) 1.0 2.9 11.9 0.9 1280 x 960

(60Hz) 3 36 960 1

SXGA (60Hz) 1.0 2.3 11.9 0.4 SXGA(60Hz) 3 38 1024 1

SXGA (75Hz) 1.1 1.8 9.5 0.1 SXGA (75Hz) 3 38 1024 1

SXGA (85Hz) 1.0 1.4 8.1 0.4 SXGA (85Hz) 3 44 1024 1

UXGA (60Hz) 1.2 1.9 9.9 0.4 UXGA (60Hz) 3 46 1200 1

W-XGA (60Hz) 1.7 2.5 16.0 0.8 W-XGA (60Hz) 3 23 768 1

SXGA+ (60Hz) 1.2 1.9 11.5 0.7 SXGA+ (60Hz) 4 32 1050 3

1280 x

800(60Hz) 1.6 2.4 15.3 0.8 1280 x

800(60Hz) 3 24 800 1

Connection to the ports

ACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT

D-sub 15pin mini shrink jack

• Video signal: RGB separate, Analog, 0.7Vp-p,

75Ωterminated (positive)

• H/V. sync. signal: TTL level (positive/negative)

• Composite sync. signal: TTL level

At RGB signal

Pin Signal Pin Signal

1Video Red 9 (No connection)

2 Video Green 10 Ground

3 Video Blue 11 (No connection)

4(No connection) 12 A

: SDA (DDC data),

: (No connection)

5 Ground 13 H. sync / Composite sync.

6 Ground Red 14 V. sync.

7Ground Green 15 A

: SCL (DDC clock),

: (No connection)

8 Ground Blue

I O

HDMI DVI-D

CONTROL IN CONTROL OUT REMOTE

CONTROL

OUT

S-VIDEO

COMPUTER IN2

COMPUTER IN1

VIDEO 1 BNC

R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2

Cb/Pb

Cr/Pr

AC IN

LAN

MONITOR

OUT

Connection to the ports

109876

54321

14131211

DBNC (G/Y, B/Cb/Pb, R/Cr/Pr, H, V)

• BNC jack x 5

• Video : Analog 0.7Vp-p, 75Ωterminator

• H/V, sync, : TTL level (positive/negative)

• Composite sync, : TTL level

COMPONENT VIDEO EY, FCb/Pb, GCr/Pr

RCA jack x3

• System: 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60, 1080i@50/60,

1080p@50/60

Port Signal

Y Component video Y, 1.0±0.1Vp-p, 75Ωterminator with composite sync

Cb/Pb Component video Cb/Pb, 0.7±0.1Vp-p, 75Ωterminator

Cr/Pr Component video Cr/Pr, 0.7±0.1Vp-p, 75Ωterminator

I O

HDMI DVI-D

CONTROL IN CONTROL OUT REMOTE

CONTROL

OUT

S-VIDEO

COMPUTER IN2

COMPUTER IN1

VIDEO 1 BNC

R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2

Cb/Pb

Cr/Pr

AC IN

LAN

MONITOR

OUT

REMOTE CONTROL KIN LOUT

Ø3.5 stereo mini jack

• To be connected with the remote control that came with the projector.

CONTROL MIN NOUT

D-sub 9pin plug

• About the details of RS-232C communication, please refer to the following RS-232C

Communication in this manual.

Pin Signal Pin Signal Pin Signal

1 (No connection) 4 (No connection) 7 RTS

2 RD 5 Ground 8 CTS

3 TD 6 (No connection) 9 (No connection)

Connection to the ports

(continued)

IVIDEO 1

RCA jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43

• 1.0±0.1Vp-p, 75Ωterminator

HS-VIDEO

Mini DIN 4pin jack

Pin Signal

1Color signal 0.286Vp-p (NTSC, burst), 75Ωterminator

Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ωterminator

2Brightness signal, 1.0Vp-p, 75Ωterminator

3Ground

4Ground

9876

54321

JVIDEO 2

BNC jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43

• 1.0±0.1Vp-p, 75Ωterminator

M N

I O

HDMI DVI-D

CONTROL IN CONTROL OUT REMOTE

CONTROL

OUT

S-VIDEO

COMPUTER IN2

COMPUTER IN1

VIDEO 1 BNC

R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2

Cb/Pb

Cr/Pr

AC IN

LAN

MONITOR

OUT

Connection to the ports

(continued)

QPO

OHDMI

• Type :Digital video connector

Pin Signal Pin Signal Pin Signal

1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL

2 T.M.D.S. Data2 Shield 9 T.M.D.S. Data0 - 16 SDA

3 T.M.D.S. Data2 - 10 T.M.D.S. Clock + 17 DDC/CEC Ground

4 T.M.D.S. Data1 + 11 T.M.D.S. Clock Shield

+5V Power

5 T.M.D.S. Data1 Shield 12 T.M.D.S. Clock - 19 Hot Plug Detect

6 T.M.D.S. Data1 - 13 CEC

7 T.M.D.S. Data0 + 14 Reserved(N.C. on device)

19 17 15 13 11 9 7 5 3 1

18 16 14 12 10 8 6 4 2

PDVI-D

DVI-D jack (digital to digital)

Pin Signal Pin Signal Pin Signal

1 T.M.D.S. Data2 - 9 T.M.D.S. Data1 - 17 T.M.D.S. Data0 -

2 T.M.D.S. Data2 + 10 T.M.D.S. Data1 +

T.M.D.S. Data0 +

3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield

4 - 12 -

5- 13- 21-

6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield

7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock +

8 - 16 Hot Plug Detect 24 T.M.D.S. Clock -

LAN

RJ-45 jack

Pin Signal Pin Signal Pin Signal

1 TX+ 4 - 7 -

2 TX- 5 - 8 -

3 RX+ 6 RX-

87654

16 15 14 13 12 11 10 9

24 23 22 21 20 19 18 17

8 7 6 5 4 3 2 1

PJLink command

Commands Control Description Parameter or Response

POWR Power Contorol 0 = Standby

1 = Power On

POWR ? Power Status inquiry

0 = Standby

1 = Power On

2 = Cool Down

INPT Input Source selection

11 = COMPUTER IN 1

12 = COMPUTER IN 2

13 = BNC

21 = COMPONENT

22 = S-VIDEO

23 = VIDEO 1

24 = VIDEO 2

31 = HDMI

32 = DVI-D

INPT ? Input Source inquiry

11 = COMPUTER IN 1

12 = COMPUTER IN 2

13 = BNC

21 = COMPONENT

22 = S-VIDEO

23 = VIDEO 1

24 = VIDEO 2

31 = HDMI

32 = DVI-D

AVMT AV Mute 30 = BLANK off

31 = BLANK on

AVMT ? AV Mute inquiry 30 = BLANK off

31 = BLANK on

ERST ? Error Status inquiry

1st byte: Refers to Fan error; one of 0 to 2

2nd byte: Refers to Lamp error; one of 0 to 2

3rd byte: Refers to Temptrature error; one of 0 to 2

4th byte: Refers to Cover error; one of 0 to 2

5th byte: Refers to Filter error; one of 0 to 2

6th byte: Refers to Other error; one of 0 to 2

The mearning of 0 to 2 is as given below

0 = Error is not detected; 1 = Warning; 2 = Error

This projector is equipped with the PJLinkTM Class 1.

See the following table for the commands for controlling the projector using the

PJLinkTM protocol are as given in the table below.

PJLink command (continued)

Commands Control Description Parameter or Response

LAMP ? Lamp Status inquiry 1st number (digits 1 to 5): Lamp Time

2nd number : 0 = Lamp off, 1 = Lamp on

INST ? Input Source List inquiry 11 12 13 21 22 23 24 31 32

NAME ? Projector Name inquiry Responds with the name set in "PROJECTOR NAME"

of "NETWORK"

INF1 ? Manufucturer's Name inquiry HITACHI

INF2 ? Model Name inquiry

CP-X10000 (XGA model)

CP-WX11000 (WXGA model)

CP-SX12000 (SXGA+ model)

INFO ? Other Information inquiry Responds with the factory information and so on

CLSS ? Class Information inquiry 1

NOTE • The password used in PJLinkTM is the same as the password set in

the Web Brouwser Comtrol. To use PJLinkTM without authentication, do not set any

password in Web Browser Control.

• For speciﬁcations of PJLinkTM, see the web site of the Japan Business

Machine and Information System Industries Association.

URL: http://pjlink.jbmia.or.jp/

RS-232C Communication

6789

12345 6789

12345

CONTROL port RS-232C cable (Cross) RS-232C port

of the projector of the computer

- (1) (1) CD

RD (2) (2) RD

TD (3) (3) TD

- (4) (4) DTR

GND (5) (5) GND

- (6) (6) DSR

RTS (7) (7) RTS

CTS (8) (8) DTS

- (9) (9) RI

Connecting the cable

1. Turn off the projector and the computer.

2. Connect the CONTROL port of the projector with a RS-232C port of

the computer by a RS-232C cable (cross). Use the cable that fulfills the

speciﬁcation shown in the previous page.

3. Turn the computer on, and after the computer has started up turn the

projector on.

Communications setting

19200bps, 8N1

1. Protocol

Consist of header (7 bytes) + command data (6 bytes).

2. Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high

CRC_low : Lower byte of CRC ﬂag for command data

CRC_high : Upper byte of CRC ﬂag for command data

3. Command data

Command data chart

byte_0 byte_1 byte_2 byte_3 byte_4 byte_5

Action Type Setting code

low high low high low high

Action (byte_0 - 1)

Action Classiﬁcation Content

1 SET Change setting to desired value.

2 GET Read projector internal setup value.

4 INCREMENT Increment setup value by 1.

5 DECREMENT Decrement setup value by 1.

6 EXECUTE Run a command.

RS-232C Communication (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2

bytes)+‘00H’ +‘00H’) from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +

setting code (2 bytes)) from the computer to the projector.

(2) The projector changes the setting based on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data

(‘06H’+‘00H’ + type (2 bytes) +‘00H’+‘00H’) to the projector.

(2) The projector changes the speciﬁed setting to the default value.

(3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data

(‘04H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector.

(2) The projector in creases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data

(‘05H’+‘00H’+ type (2 bytes) +‘00H’ + ‘00H’) to the projector.

(2) The projector decreases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

When the projector cannot understand the received command

When the projector cannot understand the received command, the error code ‘15H’

is sent back to the computer.

Sometimes the projector cannot properly receive the command. In such a

case, the command is not executed and the error code ‘15H’ is sent back to the

computer. If this error code is returned, send the same command again.

When the projector cannot execute the received command.

When the projector cannot execute the received command, the error code ‘1CH’

+ ‘xxxxH’ is sent back to the computer. When the data length is greater than

indicated by the data length code, the projector ignore the excess data code.

Conversely when the data length is shorter than indicated by the data length

code, an error code will be returned to the computer.

NOTE • Operation cannot be guaranteed when the projector receives an

undeﬁned command or data.

• Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the

lamp is lit. Ignore this data.

• Commands are not accepted during warm-up.

Command Control via the Network

Communication Port

The following two ports are assigned for the command control.

TCP #23

TCP #9715

Command Control Settings

Conﬁgure the following items form a web browser when command control is used.

Command Control via the Network

Port Settings

Network Control

Port1 (Port: 23)

Port open

Click the [Enable] check box to open [Network

Control Port1 (Port: 23)] to use TCP #23.

Default setting is “Enable”.

Authentication

Click the [Enable] check box for the

[Authentication] setting when authentication

is required.

Default setting is “Disable”.

Network Control

Port2 (Port: 9715)

Port open

Click the [Enable] check box to open [Network

Control Port2 (Port: 9715)] to use TCP

#9715.

Default setting is “Enable”.

Authentication

Click the [Enable] check box for the

[Authentication] setting when authentication

is required.

Default setting is “Enable”.

Security Settings

Network Control

Authentication

Password Enter the desired authentication password.

This setting will be the same for [Network

Control Port1 (Port: 23)] and [Network

Control Port2 (Port: 9715)].

Default setting is blank.

Re-enter

Authentication

Password

When the authentication setting is enabled, the following settings are required.

Andere Handbücher für CP-WX1100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektor Handbücher

Hitachi

Hitachi CP-EX400 Bedienungsanleitung

Hitachi

Hitachi FT-01 Bedienungsanleitung

Hitachi

Hitachi CP-X200 CP-X300 Bedienungsanleitung

Hitachi

Hitachi CP-X615 series Bedienungsanleitung

Hitachi

Hitachi CP-X445W Bedienungsanleitung

Hitachi

Hitachi IPJ-AW250N Bedienungsanleitung

Hitachi

Hitachi EDS-3170A Bedienungsanleitung

Hitachi

Hitachi CP-X608 Bedienungsanleitung

Hitachi

Hitachi ED-X40 Bedienungsanleitung

Hitachi

Hitachi CP-X2020 Bedienungsanleitung

Hitachi

Hitachi ED-X30 Bedienungsanleitung

Hitachi

Hitachi CP-X980 Bedienungsanleitung

Hitachi

Hitachi X807 - CP XGA LCD Projector Bedienungsanleitung

Hitachi

Hitachi CP-BX301WN Bedienungsanleitung

Hitachi

Hitachi CP-AW250N Bedienungsanleitung

Hitachi

Hitachi CP-X444W Bedienungsanleitung

Hitachi

Hitachi LP-TW4001 Bedienungsanleitung

Hitachi

Hitachi X1250 - XGA LCD Projector Benutzerhandbuch

Hitachi

Hitachi CP-X275 series Bedienungsanleitung

Hitachi

Hitachi CP-X2530WN Bedienungsanleitung

Hitachi

Hitachi CPX1 Series Bedienungsanleitung

Hitachi

Hitachi MP-JU4001 Bedienungsanleitung

Hitachi

Hitachi CP-WX3011N Bedienungsanleitung

Hitachi

Hitachi CP-TW3506 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung