Hitachi CP-X4021N Bedienungsanleitung

Projector

CP-X4021N/CP-X5021N

CP-WX4021N

User's Manual (detailed)

Instant Stack Guide

Thank you for purchasing this product.

This manual is intended to explain only Instant Stack feature. Other than what is

mentioned in this manual, please see other manuals of this product.

WARNING ►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

►Follow all the instructions in the manuals or on the product. The manufacturer

assumes no responsibility for any damage caused by mishandling that is beyond

normal usage dened in the manuals.

NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

Trademark acknowledgment

All the trademarks in this manual are the properties of their respective owners.

Features

This projector can be used with one more same type projector to make one image

on one screen with Instant Stack feature.

The two projectors can work simultaneously to make the image brighter.

Moreover, if you connect two projectors with RS-232C cross-over cable, it turns to

a kind of intellectual stacking system. The two projectors can work alternately by

themselves, and once one projector has an accident the other voluntarily starts to

work to keep your presentation going.

These features, generically called Instant Stack, provide you with the broad use.

 

1. Introduction ........................3

1.1 Entries and graphical

symbols explanation........................ 3

1.2 Important safety instruction .......... 3

For Instant Stack feature ..................... 3

For general installation ........................ 5

1.3 Basic information

and preparation ............................... 6

Instant Stack ........................................ 6

Intellectual Stack and Simple Stack..... 6

Remote control for Intellectual Stack

and Simple Stack ............................ 6

Installation styles ................................. 6

Tentative naming of two projectors ...... 6

2. Installation ..........................7

2.1 Preparation with powered up........ 7

2.2 Installation of

the rst projector (Set A) ................ 8

Removing pocket caps ........................ 8

Preparing of elevator feet .................... 8

Deciding installation position ............... 8

Setting up Set A................................... 9

2.3 Installation of

the second projector (Set B) ........ 11

Piling up projectors ............................ 11

Connecting projectors........................ 11

Setting up Set B................................. 12

2.4 Conrmation of Main

& Sub setting ................................. 14

2.5 Fine adjustment

of image position ........................... 15

For Intellectual Stack users ............... 15

For Simple Stack users...................... 16

3. Setting on STACK menu ..17

3.1 Displaying STACK menu ............ 17

3.2 Selecting Main, Sub or off .......... 18

3.3 Selecting lamp working mode..... 19

3.4 Selecting lamp switching mode .. 21

3.5 Selecting input source to Sub..... 22

3.6 Exiting STACK menu .................. 23

In STACK menu ................................. 23

In a dialog from STACK menu ........... 23

3.7 Important information

for Intellectual Stack ...................... 24

4. Connecting cables ...........27

4.1 Connecting RS-232C cable........ 27

4.2 Connecting signal cables............ 28

Inputting image to Sub from Main...... 28

Inputting image

to Sub and Main individually........... 28

5. Setting for input port

on menu ..............................29

5.1 Preparing menu operation.......... 29

5.2 Checking Main projector’s

operating status............................. 29

5.3 Starting Main projector ............... 30

5.4 Setting on menu ......................... 31

Inputting image to Sub from Main

- Computer signal ........................... 31

Inputting image to Sub from Main

- Video signal

(either COMPONENT or VIDEO) ... 32

Inputting image of

Sub and Main individually............... 31

6. Restriction

on Schedule function ........34

7. Troubleshooting ...............36

Contents

1.1 Entries and graphical symbols explanation

The following entries and graphical symbols are used for the manuals and the

product as follows, for safety purpose. Please know their meanings beforehand,

and heed them.

1.2 Important safety instruction

The followings are important instructions for safely using the product in Instant

Stack. First of all, read the following instructions and be sure to follow them al-

ways when using the Instant Stack of this product.

(continued on next page)

WARNING This entry warns of a risk of serious personal injury or even

death.

CAUTION This entry warns of a risk of personal injury or physical

damage.

NOTICE This entry notices of fear of causing trouble.

WARNING ► Take a special care not to fall the stacked projectors.

• When stacking two projectors, make sure the elevator feet and heel of the

upper projector are inserted into the corresponding pockets of the lower

projectors. (

)

• When using the Instant Stack by piling up two projectors, you can change the

projection angle by adjusting the elevator feet of the

unit that is placed underneath. (

) Exercise care

to prevent the stacked projector from falling off or

tipping over while adjusting the elevator feet.

• Pile up two projectors as maximum and do not pile

up three projectors or more.

• Do not install the projectors that are piled up with

using the stack pockets, elevator feet and heel of

the projectors at a place higher than man.

• Do not install the projectors that are piled up with

using the stack pockets, elevator feet and heel of

the projectors on a ceiling.

• Do not touch the stacked projectors except when

instructions are given in this manual. Do not hit the

projectors with any type of object.

Pocket cap

Stack pocket

LOCK

Elevator feet

Heel

Cap storage

pocket

Lens

adjuster

door

Stack

pocket

1. Introduction

For Instant Stack feature

Introduction

1.2 Important safety instruction - For Instant Stack feature (continued)

NOTICE ► Instant Stack is a feature that brings you a very convenient way to

pile up or line up two projectors. The images projected from the two projectors

may not be able to be nely superimposed on screen depending on the position

or environmental of the projectors. Especially, if the screen is curved or

distorted or unlevel, the images will not be nely superimposed.

• Just after turning on, the projected images will not be so stable since the

temperature inside of the projectors is rising. Wait 20 minutes or more after

turning on, before you start to adjust images to superimpose.

• The images may be shifted by temperature change, vibration and shock of

being hit by something. When you use Instant Stack, install them in stable

environment. If the images are shifted, adjust them again. (

9, 12, 15

)

• The images may be shifted with time by the tension or weight of connected

cables. Pay attention to arrangement of cables not to place burden to the

projectors.

• It may be happened to make a mechanical noise and degrade image quality

by sympathetic vibration with the piled up projectors if the volume of built-in

speakers is set much higher. In this case, check the volume setting on both

projectors, and lower the volume to remove such phenomena or place the

projectors side by side.

• With RS-232C connection between two projectors, a projector as Main can

control the other as Sub, which is a feature called as Intellectual Stack. (

)

If you use the feature, you cannot use RS-232C communication to control

projectors, since RS-232C function is occupied with Intellectual Stack. If you

wish to control projectors, use LAN connection that can be connected with

one of the projectors.

• When you use Intellectual Stack, the operations or setting of some functions

are restricted. Refer to this manual for detail. (

)

WARNING ► Be sure to storage the pocket caps reliably and safely inside

of the lens adjuster door to prevent children and pets from swallowing the caps,

when taking the caps from the in stack pockets. (

) If they swallow the caps,

consult a physician immediately for emergency treatment.

CAUTION ► Be careful not to injure your nail and nger to remove the

pocket caps. (

)

Introduction

For general installation

NOTICE ► Position the projector to prevent light from directly hitting the

projector’s remote sensor.

• Do not place the product in a place where radio interference may be caused.

CAUTION ► Place the projector in a cool place with sufcient ventilation.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as a wall. If you install two projectors in Style 2 (

), keep a

space of 30 cm or more between the two projectors.

• Do not stop up, block nor cover the projector’s vent holes.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction.

► Avoid placing the projector in smoky, humid or dusty place.

• Do not place the projector near humidiers. Especially for an ultrasonic

humidier, chlorine and minerals contained in tap water are atomized and

could be deposited in the projector causing image degradation or other

problems.

WARNING ► Install the projector where you can access the power outlet

easily.

► Do not subject the projector to unstable conditions. Install the projector in a

stable horizontal position.

• Do not use any mounting accessories except the accessories specied by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your

dealer beforehand. Specic mounting accessories and services may be

required.

► Do not install the projector near thermally conductive or ammable things.

► Do not place the projector where any oils, such as cooking or machine oil,

are used.

► Do not place the projector in a place where it may get wet.

Introduction

Tentative naming of two projectors

To be easy to follow the explanation, the following

names are used in the manual for piling up installa-

tion.

Set A : A projector placed underneath

Set B : A projector placed over Set ASet A

Set B

Installation styles

There are following two styles to install two projectors. Instant Stack can support

both of them.

Style 1: Piling them up vertically

Style 2 : Lining them up horizontally

This manual is mainly explained the installation of Style 1. If you wish to install

two projectors in Style 2, refer to the articles you need in this manual.

1.3 Basic information and preparation

Instant Stack

Instant Stack is the feature that brings you very convenient way to superimpose

the images projected by two projectors. The projector is specially designed to

support the feature, and has some functions to support you to install two projec-

tors and superimpose the images.

Intellectual Stack and Simple stack

Instant Stack covers both of the following two features.

If you link two projectors with an RS-232C cable and make necessary setting on

the projectors, the projectors will automatically collaborate to work under the set-

ting. This use is called as Intellectual Stack in this manual.

If you do not connect an RS-232C cable, the projectors will work individually. This

use is called as Simple Stack in this manual.

Remote control for Intellectual Stack and Simple Stack

In Intellectual Stack use, one projector is set as Main and the other is set as Sub.

(

) If you use Intellectual Stack, only the projector as Main can receive the

remote control signal. Even if you want to operate the other as Sub , you need to

point at the Main with the remote control.

If you use Simple Stack, both projectors can receive the remote control signal. To

avoid the operation by the remote control to being mixed up, it is recommended to

operate one projector by the remote control and to operate the other by the con-

trol panel on the projector or wired remote. In this case the other projector should

disable the remote control by KEY LOCK. (Operating Guide → OPTION menu)

Before installation, read carefully Important safety instruction (

3~5

) for safety

reason. And note the followings for proper use of the Instant Stack.

●When you use Intellectual Stack, until you set STACK MODE to SUB on one

projector, both projectors can react to the remote control signal.

For installation, it is recommended to operate one projector by the remote

control and to operate the other by the control panel on the projector or wired

remote. In this case the other projector should disable the remote control by

KEY LOCK.(Operating Guide → OPTION menu)

●Even if the images of Set Aand Set Bare fully superimposed once, it may shift

over time.

Adjust the images again to superimpose the image.

●It may be happened to make a mechanical noise and degrade image quality by

sympathetic vibration with the two projectors if the volume of built-in speakers is

set to much higher.

In this case, check the volume setting on both projectors, and lower the volume

to remove such phenomena. In case the image position is shifted, adjust it

again.

2.1 Preparation with powered up

If you wish to use Intellectual Stack with RS-232C cable connection, the following

setting must be conrmed on both of projectors. Otherwise, menus for Intellectual

Stack on the projectors cannot be operated.

●STANDBY MODE in SETUP menu: NORMAL

(Operating Guide → SETUP menu)

●COMMUNICATION TYPE in COMMUNICATION in SERVICE menu: OFF

(Operating Guide → OPTION menu)

●STACK LOCK in SECURITY menu: OFF

If STACK LOCK is set on, any menu related to Instant Stack cannot be

operated. So, it is required to set to off for installation and setting on menu.

(1) Using the ▲/▼/◄/► buttons, go down the menu tree as below;

ADVANCED MENU > SECURITY

> STACK LOCK

STACK LOCK dialog will appear on screen. (Operating

Guide → SECURITY menu)

(2) Use the ▲/▼ buttons to point at OFF, and press the ► button to complete

the setting.

2. Installation

Installation

NOTE • The angle of gradient of Set A to the horizontal line should be within

12 degrees.

• Keep in mind the followings when you consider the installation position.

-VERTICAL adjuster should be set to upper limit position.

- ZOOM ring should not be set to fully wide position.

- HORIZONTAL adjuster is recommended to be set around center position.

Preparing of elevator feet

When you pile up two projectors, set the elevator feet

length minimum with using the elevator buttons on Set

Aand B.

CAUTION ►Be careful that when you pile up

two projectors, a projector set over the other may

slide down.

NOTE • Cap storage pockets for the pocket caps

are provided inside of the lens adjuster door. Be

sure to keep the caps in the storage pockets, when

taking the caps from the stack pockets.

To store the cap to the pocket, put thin side of the

cap to the pocket rst, and then rmly push down

the other side of the cap to the bottom end of the

pocket. Be aware that keeping the caps solidly is

extremely important to prevent children and pets

from swallowing the caps.

LOCK

Thin side

Cap storage

pocket

Pocket caps

CAUTION ►It is recommended to use a pin or

something similar to remove the caps. If you use

your nger, be careful not to injure your nail and n-

ger.

Removing pocket caps

When you pile up two projectors, remove pocket caps

on Set A.

Deciding installation position

Decide the position of Set A and its projection angle. (User’s Manual (concise)

→Arrangement and Adjusting the projector’s elevator.)

2.2 Installation of the rst projector (Set A)

Installation

2. Set the lens position to upper limit with VERTICAL adjuster.

NOTE • If it is not set to upper limit, the image of Set B may not be able to

fully overlap to the image of Set A.

• If necessary, set MIRROR rst, since the setting change may shift the image

position. (Operating Guide →SETUP menu)

• HORIZONTAL adjuster is recommended to be set around center position.

3. Adjust the image of Set Ato match your screen with using VERTICAL adjust-

er, HORIZONTAL adjuster, ZOOM ring and FOCUS ring. (User’s Manual

(concise) →Displaying the picture)

If necessary, also use KEYSTONE and PERFECT FIT to set the image posi-

tion. (Operating Guide →EASY MENU or SETUP menu).

NOTE • ZOOM ring should not be set to fully wide position, otherwise the

image of Set B may not be able to fully overlap to the image of Set A. Be

aware that the image size of Set B must be set a little wider than the one of

Set Ausing ZOOM ring, since electrical ne tuning of image position of Set B

never widen the image size of Set B.

• When you use PERFECT FIT, KEYSTONE cannot be operated. If you

require to adjust the image with KEYSTONE and PERFECT FIT, adjust it with

KEYSTONE rst.

• If you use Simple Stack, go to Installation of the second projector (Set B).

(

)

(continued on next page)

Setting up Set A

1. Turn on Set A.

4. Display a menu with MENU button. (Operating Guide →Using the menu

function)

5. Using the ▲/▼/◄/► buttons, go down the menu tree as below.

ADVANCED MENU > OPTION

> SERVICE > COMMUNICATION

> STACK

STACK menu will appear on screen.

(Operating Guide →OPTION menu).

Installation

NOTE • During the installation, Set A will not be operated by the remote

control after that. So, it is recommended to disable the remote control by KEY

LOCK, to avoid the operation by the remote control to being mixed up.

• After STACK MODE setting is completed, Set A (Sub) cannot receive the

remote control signal. When you set STACK MODE to OFF, enable the

remote control by KEY LOCK if necessary.

8. Disable the remote control by KEY LOCK if you use Intellectual Stack.

(Operating Guide →OPTION menu)

7. After pressing the ► button, a dialog to

conrm whether or not the setting is saved is

displayed.

Press the ► button to complete the setting. (

)

Installation of the rst projector (Set A) - Setting up Set A (continued)

6. Use the ▲/▼ buttons to point at STACK

MODE, and press the ► button to display

STACK MODE dialog.

Point at SUB pressing the ▲/▼ buttons, and

press the ► button.

Andere Handbücher für CP-X4021N

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektor Handbücher

Hitachi

Hitachi Innovate CP-RX93 Bedienungsanleitung

Hitachi

Hitachi CP-X444W Bedienungsanleitung

Hitachi

Hitachi CP-X417 series Bedienungsanleitung

Hitachi

Hitachi X995 - CP XGA LCD Projector Bedienungsanleitung

Hitachi

Hitachi CP-AW2503 Bedienungsanleitung

Hitachi

Hitachi CP-X615W and Technisches Dokument

Hitachi

Hitachi CP-DW25WN Bedienungsanleitung

Hitachi

Hitachi CP-X2011N Bedienungsanleitung

Hitachi

Hitachi CP-X2530WN Bedienungsanleitung

Hitachi

Hitachi CP-AW312WN guide Bedienungsanleitung

Hitachi

Hitachi CP-DW10N Bedienungsanleitung

Hitachi

Hitachi CP-A200 Bedienungsanleitung

Hitachi

Hitachi CP-WX4021N Bedienungsanleitung

Hitachi

Hitachi CP-X970W Bedienungsanleitung

Hitachi

Hitachi CP-WX11000 Bedienungsanleitung

Hitachi

Hitachi LP-WU3500 Bedienungsanleitung

Hitachi

Hitachi PJ1065 Bedienungsanleitung

Hitachi

Hitachi EDPJ32 Bedienungsanleitung

Hitachi

Hitachi HOME-1 Bedienungsanleitung

Hitachi

Hitachi CP-X4020 Bedienungsanleitung

Hitachi

Hitachi CP-X201 Technisches Dokument

Hitachi

Hitachi CP-L750W Bedienungsanleitung

Hitachi

Hitachi CP-X990W Bedienungsanleitung

Hitachi

Hitachi CP-S310W Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung