Hitachi L19DP03C Bedienungsanleitung

CAUTION:

Before servicing this chassis, it is important that the service technician read the “Safety

Precautions” and “Product Safety Notices” in this service manual.

ATTENTION:

Avant d’effectuer l’entretien du châssis, le technicien doit lire les «Précautions de sécurité»

et les «Notices de sécurité du produit» présentés dans le présent manuel.

VORSICHT:

Vor Öffnen des Gehäuses hat der Service-Ingenieur die „Sicherheitshinweise“ und „Hinweise

zur Produktsicherheit“ in diesem Wartungshandbuch zu lesen.

SERVICE MANUAL

MANUEL D'ENTRETIEN

WARTUNGSHANDBUCH

Data contained within this Service

manual is subject to alteration for

improvement.

Les données fournies dans le présent

manuel d’entretien peuvent faire l’objet

de modifications en vue de perfectionner

le produit.

Die in diesem Wartungshandbuch

enthaltenen Spezifikationen können sich

zwecks Verbesserungen ändern.

«MODEL NAMES»

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

Colour Television

May 2009

No. 0250

L19DP03C

L19DP03U

L19HP03C

L19HP03U

FOR ALL PARTS PLEASE MAKE

CONTACT WITH ASWO.

FOR YOUR LOCAL OUTLET GO TO

www.aswo.com

TABLE OF CONTENTS

1 INTRODUCTION....................................................................................................3

2 GENERAL DESCRIPTION...................................................................................3

3 POWER CONSUMPTION.....................................................................................6

4 MICROCONTROLLER PORT CONFIGURATION.........................................6

5 SIDE BOARDS AND CONNECTORS .................................................................7

5.1 Keypad .........................................................................................................................................7

5.2 Infrared & LED ...........................................................................................................................7

5.3 DVB-T .........................................................................................................................................8

5.4 DVD.............................................................................................................................................9

5.5 LVDS .........................................................................................................................................11

5.6 Inverter.......................................................................................................................................12

6 IC SPECIFICATIONS..........................................................................................13

6.1 Microcontoller/Video&Audio Processor (VCT4953G) ............................................................13

6.2 Scaler/De-interlacer (MST5x7A-M)..........................................................................................16

6.3 Audio Amplifier (TDA2822).....................................................................................................19

6.4 HeadPhone Amplifier (TDA1308T) ..........................................................................................19

6.5 Audio Matrix Switch (TEA6422D) ...........................................................................................20

6.6 HDMI Receiver (ANX9021) ....................................................................................................21

6.7 Video Switch (PI5V512)...........................................................................................................23

6.8 Tuner (DTT71306).....................................................................................................................24

6.9 SAW Filter (X6966M)...............................................................................................................25

6.10 I2C Switch (74HCT4053)..........................................................................................................26

6.11 Audio DAC (CS4334)................................................................................................................27

6.12 SPDIF Switch (NLAST4599) ....................................................................................................28

1 INTRODUCTION

The purpose of this document is to define the operation of 17MB27 chassis, capable of driving 15” and

19” TFT LCD panels. It is aimed to provide information to engineering staff to understand the operation

and specs of the TV. The other related technical documents are given in Table1:

Title

1 17MB27 schematics

2 IR receiver and LED display board schematics

3 Keypad board schematics

4 DVD module card schematics

5 DVB-T module card schematics

Table1.1: Related documents

2 GENERAL DESCRIPTION

The system is a low to mid end; 15” and 19” TFT TV solution basically for EU market with VCT4913G

microcontroller / video audio processor chip on a 2-layer PCB. Since the target market is EU, the first

release of the TV will support PAL/SECAM B/G/D/K/I/L/L’.

The target panels are 15” 1024x768 and 19”w 1440x900 TFT-LCD panels. A DVD loader is used to read

DVD content and a DVB-T module card is used to support DVB-T. 15” TV will use 12V/4.16A DC

adapter; 19” TV will use 12V/5.83A DC adapter.

Inputs

•1xTuner (both analog and DVB-T)

•1xDVD

•1xScart

•1xPC (VGA) (optional) (supports also YPbPr)

•2xHDMI (optional)

•1xBack AV (optional)

Outputs

•Speaker (stereo, 2x16 , 2x2Watt)

•Headphone (stereo) (optional)

•Audio line out (stereo) (optional)

•DVD/DVB-T coaxial SPDIF out(optional)

General default features

•Multi System Reception: PAL-SECAM BG-DK-I/I’-L/L’

•Menu system (multi language)

•100 program storage locations

•OSD (on-screen display)

•Teletext

•IR Control (RC5 and other customer specific protocols)

•“No Ident” Timer

•Child Lock

•Sleep Timer

•WSS (16:9/4:3 Aspect Ratio Auto Switch)

Sound Features

•Equalizer

•FM Radio

•Linear Stereo

•German-NICAM Stereo

•5-Band Equalizer Control

•SRS TRU Surround (OPT)

•SRS TRU Bass (OPT)

•BBE, WOW (OPT)

Picture Features

•4:3 PANEL --- 4:3, 16:9, Auto

•WIDE PANEL---4:3,16:9, Auto(opt), Subtitle(opt), Zoom(opt), Panoramic(opt)

•Picture Modes ( Bright, Standard, Soft)

•Media Window Enhancement (MWE)

•White balance settings (warm/normal/cool) for TV&PC

•Backlight brightness setting (movie/normal/bright)

•Multi System Reception : PAL-SECAM BG-DK-I/I’-L/L’

•NTSC Video Playback

•WSS (16:9 / 4:3 Aspect Ratio Auto Switch)

•Channel Type Sorting (Favorite/Sport/Music/News/Movie)

Tuning Options

•FST

•Frequency Search (Optional)

•APS (Auto Search/Name/Sort)

•Auto Search

•CATV/HYPERBAND

Keyboard

•Volume -/ +Button

•Program -/+ Button

•Menu Button

•TV / AV Button

Teletext/OSD

•Simple Text 10 Pages

•Fastext & Top Text (OPT)

•Teletext Languages (ALL)

•Character Based OSD

•OSD Color & Transparency Selection

Electrical features

•12V 4.16A DC / 100 - 240V AC adapter for 15” TV

•12V 5.83A DC / 100 - 240V AC adapter for 19” TV

•<1W standby power consumption

System Building Blocks

17MB27 chassis main blocks are as follows:

•Analog Front End : VCTI (Microcontroller+Video Proccessor+Audio Proccessor+IF Demodulator+

Teletext Decoder+ OSD Generator)

•Back End : MST517a-M, MST507a-M (Scaler, Deinterlacer, OSD Generator)

Analog Front End

17MB27 main board consists of two major blocks. The first block is analog front-end and this block is

handled by VCTI chip that is highly multifunctional. VCTI performs Tuner IF demodulation, CVBS,

RGB, SVHS and audio input selection and processing. The audio processor (MSP) supports equalizer,

tone control, volume control, AVL, surround effect etc. The video processor (VSP) handles video

processing such as color standard detection and demodulation, picture alignment (brightness, contrast,

color etc.). The IC also has a teletext decoder with fastext memory. The processed video output is sent to

MST5x7A-M, scaler/deinterlacer in RGB format together with a composite sync.

The TV tuner is PLL controlled symmetrical IF output type. The IF signal is filtered by a single SAW

filter. Inter-carrier sound demodulation is performed by the system. After the SAW filter block, IF signal

is processed by VCTI IF demodulator. Audio signal is digitally filtered in the IF demodulator block. The

same IF signal is buffered and sent to DVB-T module card, tdm1300.

Since VCTI can handle all the audio processing, there is no need for additional audio processor solution on

the board. MSP has two audio inputs which are assigned to the Scart in L/R and Audio Switch L/R output.

MSP has three audio outputs which are assigned to the headphone amplifier L/R input, audio amplifier

L/R input and Audio switch L/R input. The board employs TDA2822M and TDA1308 to drive speaker

and headphone outputs, respectively. Switching control for other audio inputs and outputs (HDMI, Back

AV, PC, DVD, and DVB-T) is achieved by an I2C controlled audio switch (TEA6422).

Back End

MST5x7A-M has two ADC inputs. First ADC input is assigned to the VCTI RGB output. Other

RGB/YPbPr inputs are multiplexed for the second ADC input. HDMI receiver ANX9021 analog output,

VGA RGB input and the synchronization signals are multiplexed by a primary RGB switch (PI5V512).

MST5x7A-M has an embedded LVDS transmitter. It can be configured as either single LVDS, or dual

LVDS output.

There are three PWM output ports. PWM0 is assigned to analog/digital dimming control for the backlight,

PWM1 is used for backlight on/off and panel logic power supply on/off control and PWM2 is used to

control PC/HDMI switch IC (PI5V512).

3 POWER CONSUMPTION

The power block diagram with the currents drawn is shown below:

4 MICROCONTROLLER PORT CONFIGURATION

NO PORT

NAME SIGNAL NAME TYPE FUNCTION

47 P10 MST_RESET

PROTECT

Scaler reset

Short circuit detection

48 P11 TV_RXD I IDTV UART receive signal

49 P12 TV_TXD O IDTV UART transmit signal

50 P13 IRQ O IDTV interrupt request signal

51 P14 KEY I Keyboard function select

52 P15 SC_PIN8 I Scart function select

53 P16 DVD_IR_ON/OFF O DVD infrared signal on/off control

54 P17 POWCON O Standby on/off control

NO PORT

NAME SIGNAL NAME TYPE FUNCTION

55 P20 HDMI_HP_INV O HDMI hot plug signal

56 P21 CS O Switching control for Mstar bus and system I2C

62 Safety VCTI_HS O VCTI composite sync output

78 FBIN DVD_SENSE I DVD module detection

85 Vert+ TV/DVB_SW O IDTV/TV I2C and AGC switch control for tuner

27 P22 WP O Write protection control for NVM

28 P23 IR I Infrared input

Table 4.1 VCTI port configuration

5 SIDE BOARDS & CONNECTORS

5.1 Keyboard

A four-pin connector is used between 17mb27 and the keyboard:

Figure 5.1.1: Keyboard connector

KEY signal is sent directly to microcontroller ADC port and depending on the voltage level of KEY

signal, microcontroller performs one of these actions: menu, program+, program-, volume+, volume-, and

source.

SOFT_SW signal is used to switch between “power-off” and “standby” modes.

5.2 Infra-red & LED

A five-pin connector is used between 17mb27 and the LED board:

Figure 5.2.1: LED board connector

Pin2 and pin3 carry the control signals for the LED. Pin4 carries the infra-red signal to the microcontroller.

Pin5 is used to power up the LED board.

5.3 DVB-T module board

DVB-T module board (tdm1300) is used to receive digital terrestrial broadcast signals. Three cables are

used to connect 17mb27 and tdm1300: power, data, and IF.

12V (500mA) is sent to tdm1300 by power cable:

Figure 5.3.1: DVB-T module card power connection on 17mb27

Analog RGB(YPbPr), CVBS, stereo audio, tuner control (SCL, SDA, AGC), and three GPIO port outputs

of tdm1300, together with UART ports (TV_RXD, TV_TXD, IRQ) are carried by data cable.

Figure 5.3.2: DVB-T data connector on 17mb27

Tdm1300 board has no tuner on it. Instead, the tuner of 17mb27 is used for both analogue and digital

reception. Tuner is controlled by either the 17mb27 microcontroller (VCTI), or tdm1300 board

microcontroller. The IF (intermediate frequency) output of the tuner is sent to tdm1300 board for digital

reception.

Figure 5.3.3: IDTV IF connector on 17mb27

5.4 DVD module board

DVD module board has two parts: a loader and an electronic card. Electronic card controls the loader and

has connections with 17mb27 and DVD keypad.

Three cables are used to connect 17mb27 and DVD electronic card: power, data, and sense.

12V (500mA) is sent to DVD electronic card by power cable:

Figure 5.4.1: DVD module board power connection on 17mb27

Y/C and/or CVBS video, stereo audio outputs and infra-red input of DVD module board is carried on data

cable:

Figure 5.4.2: DVD data connector on 17mb27

When a DVD is inserted into the loader, the DVD electronic card sends an interrupt signal (DVD_SENSE)

to the 17mb27 microcontroller:

Andere Handbücher für L19DP03C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Fernseher Handbücher

Hitachi

Hitachi 49HK6T74U Bedienungsanleitung

Hitachi

Hitachi 43HK6500 Bedienungsanleitung

Hitachi

Hitachi CK-200 Bedienungsanleitung

Hitachi

Hitachi 42HDF52 - 42" Plasma TV Bedienungsanleitung

Hitachi

Hitachi 32LD9800TA Bedienungsanleitung

Hitachi

Hitachi L19DP03U A Bedienungsanleitung

Hitachi

Hitachi 51F510 DP43 Bedienungsanleitung

Hitachi

Hitachi 43HAK6150U H Bedienungsanleitung

Hitachi

Hitachi 42PD9700N Bedienungsanleitung

Hitachi

Hitachi C24W430N Bedienungsanleitung

Hitachi

Hitachi 27CX28B Bedienungsanleitung

Hitachi

Hitachi LE42S605 Bedienungsanleitung

Hitachi

Hitachi 55R81 Bedienungsanleitung

Hitachi

Hitachi 32C11 Bedienungsanleitung

Hitachi

Hitachi 15LD2200 Bedienungsanleitung

Hitachi

Hitachi 49HK5600 Bedienungsanleitung

Hitachi

Hitachi Opus C2164TN Bedienungsanleitung

Hitachi

Hitachi ULTRAVISION 49C60 Bedienungsanleitung

Hitachi

Hitachi 65QLEDSM20 Bedienungsanleitung

Hitachi

Hitachi 42PD9700C Bedienungsanleitung

Hitachi

Hitachi 55HK6200U Bedienungsanleitung

Hitachi

Hitachi CBP260 Montageanleitung

Hitachi

Hitachi 36UX59B Bedienungsanleitung

Hitachi

Hitachi L32R100 Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Philips

Philips Colour Television Bedienungsanleitung

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung

Sylvania

Sylvania 6427FB Bedienungsanleitung