Hitech EZ Cutter 200 Bedienungsanleitung

User Guide: EZ Cutter 200

Physical Setup

Unlock the machine

Swipe your student card in

front of the card reader. If

you’ve booked the laser

cutter at the current time

period the machine will

turn on.

If the machine doesn’t turn

on re-check the time

period of your booking.

Otherwise contact the

workshop staff.

Initialize the machine

First, open the lid on the

laser cutter and make

sure that there are no

leftover materials

inside the machine.

Afterwards press

“Run”.

NOTE: If there are any sort

of material on the tray,

remove them before

proceeding to the next step.

“Homing” the laser cutter

Press “Press here to

do homing“.

The machine will move

the laser head to home

position (x,y = 0,0)

and will then be ready

for use.

The Operation screen

“OPER.” is short for Operation

and is the screen used to start

and stop the laser cutter once

your job has been uploaded.

After uploading your cutting job

from the connected PC the

cutting won’t begin before you

press the “Start”-button. Pressing

“Pause” will stop the cutting

when the current cutting line is

complete. Afterwards a

“Resume”-button appears on the

screen an pressing this will

continue the cutting job.

Moving the laser head

“FOCUS” is for manually

moving the laser head around.

Use the arrows to move the

laser head around.

“P1” is for moving the laser

head to the lower left corner

and “P2” to the upper right

corner.

The Red Pointer

1. Switch to the “CONFIG” menu.

2. Press on the “Output” menu

3. Switch the “Red Pointer” from

“OFF” to “ON”

4. Exit the menu and the machine

will show the red pointer from

now on.!

If you need to turn on the

red pointer use the

following steps:

Place the laser head in the lower

left corner of the machine (where

the coordinates x,y = 0,0). Then

place the lower left corner of

your material at x,y =0,0 (if the

“red pointer” is On then the red

dot should be exactly at the

corner of your material)

To make sure your material is

placed parallel to the x- and y-

axis, use the touch display to

move the laser head along the x-

axis and you should see the red

pointer moving exactly on the

edge of the material at all time.

Placing the material

Setting correct focus

Place the 2”-distance-block

perpendicular to your material and

turn the knob until the block exactly

ﬁts in the cavity of the lowest tray

on the laser head.

Spin this knob to adjust the height

of the laser head.

If your material is not completely

planar the focus will change along

the material. This will result in

varied cutting performance on

different areas of the material. Only

solution is to buy only perfectly

planar plates for laser cutting.

Inhaltsverzeichnis

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung