HK Instruments DPI Series Bedienungsanleitung

INSTALLATION

INSTRUCTIONS

DIFFERENTIAL PRESSURE SWITCHES

DPI Series

• READ THESE INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS

DEVICE.

• Failuretoobservesafetyinformaonandcomplywith

instruconscanresultinPERSONALINJURY,DEATHAND/OR

PROPERTY DAMAGE.

• Toavoidelectricalshockordamagetoequipment,disconnect

powerbeforeinstallingorservicinganduseonlywiringwith

insulaonratedforfulldeviceoperangvoltage.

• Toavoidpotenalreand/orexplosiondonotuseinpotenally

ammableorexplosiveatmospheres.

• Retaintheseinstruconsforfuturereference.

• Thisproduct,wheninstalled,willbepartofanengineered

systemwhosespecicaonsandperformancecharacteriscs

arenotdesignedorcontrolledbyHKInstruments.Review

applicaonsandnaonalandlocalcodestoassurethatthe

installaonwillbefunconalandsafe.Useonlyexperiencedand

knowledgeabletechnicianstoinstallthisdevice.

SPECIFICATIONS

ThankyouforchoosinganHKInstrumentsDPIserieselectronicdif-

ferenalpressureswitch.TheDPIseriesisintendedforuseincom-

mercialenvironments.Itcombinestheadvantagesofanelectronic

dierenal pressure switch (on-o relay) and a mul-funconal

dierenal pressure transmier to meet your applicaon require-

ments.

The DPI series is comprised of the DPI±500 with bi-direconal

measurementrangesfrom±100to±500PaandtheDPI2500with

measurementrangesfrom100to2500Pa.

AllDPIseriesdevicesincludeonerelay,display,manualpushbuon

zeropointcalibraonandspanpointcalibraon.Oponalfeatures

includeasecondrelayandautozerocalibraon.

DPIseriesdevicesarecommonlyusedinHVAC/Rsystemsfor:

•fan,blowerandltermonitoring

•staircasepressuremonitoringandalarm

•pressuremonitoringincleanrooms

•boilerpressuremonitoringandalarm

SPECIFICATIONS

Performance

Accuracy:

±1.5%(±0.7%*)

%FSfromhighestpressurerange(including:

generalaccuracy,temperaturedri,linearity,hysteresis,

andrepeonerror)

*Canbeachievedwithspanpointcalibraon

Long term stability:

Typical1year

Withautozero:±1Pa

Withoutautozero:±8Pa

Thermal eects:

Temperaturecompensatedacrossthefullspectrumof

capability

Overpressure:

Proofpressure:25kPa

Burstpressure:30kPa

Zero point calibraon:

Automacwithautozero(-AZ)circuitor

Manual via menu

Response me:

0.5–10s,selectableviamenu

Technical Specicaons

Media compability:

Dryairornon-aggressivegases

Measuring units:

Pa,kPa,mmWC,inWC,mbarselectableviamenu

Measuring element:

Piezoresisve

Environment:

OperangTemperature:

 Withoutautozero:-10...50°C

 Withautozero:-5...50°C

Storagetemperature:-20...70°C

Humidity:0to95%rH,noncondensing

Physical

Dimensions:

Case:89x86.5x37.1mm

Weight:

150g

Mounng:

Case:2each4.3mmholes

Lid:2each4.3mmholes

Materials:

Case:ABS

Lid:PC

Ductconnectors:ABS

Tubing:PVC

Protecon standard:

IP54

Touchsensivebuonsonthelid:

Menu,Back,OK,downarrow,uparrow

Display:

31/2digitLCDbacklitdisplay

Size:46.0Wx14.5Hmm

Electrical connecons:

n/out:

 Terminalblock(24V,GND,0–10V)

 Wire:0.2–1.5mm2(12–24AWG)

Relay1:

 Terminalblock(NC,COM,NO)

 Wire:0.2–1.5mm2(12–24AWG)

Relay2:

 Terminalblock(NC,COM,NO)

 Wire:0.2–1.5mm2(12–24AWG)

Cable entries:

Strainrelief:M16&M20

Knockout:16mm

Knockout:20mm

Pressure ngs:

5.2mmbarbedbrass

 +Highpressure

 −Lowpressure

Electrical

Circuit:3-wire(24V,GND,0–10V)

Input:

 Withoutautozero:21–35VDC/24VAC,±10%

 Withautozero:24VACorVDC,±10%

Output:

 Analog:0–10V

 Relay1:250VAC/30VDC/6A

 Relay2:250VAC/30VDC/6A

 Adjustableswitchingpointandhysteresis

Zero/Spanoutputcalibratedwithin±0.025V

Resistanceminimum:1kΩ

Currentconsumpon:

 35mA+relays(7mAeach)+AZcircuit(20mA)

 +0–10Voutput(10mA)

Conformance

MeetsrequirementsforCEmarking:

EMCDirecve2014/30/EU

RoHSDirecve2011/65/EU

LVDDirecve:2014/35/EU

WEEEDirecve2012/19/EU

INTRODUCTION

APPLICATIONS

WARNING

COMPANY WITH

MANAGEMENT SYSTEM

CERTIFIED BY DNV GL

= ISO 9001 = ISO 14001 =

RoHS 2

2011/65/EU

SCHEMATICS

DIMENSIONAL DRAWINGS

INSTALLATION

Figure 1a - Surface mounng

STEP 1: MOUNTING THE DEVICE

1)Mountthedeviceinthedesiredlocaon(seestep1).

2)Openthelidandroutethecable(s)throughthestrainrelief(s)and

connectthewirestotheterminalblock(s)(seestep2).

3)Thedeviceisnowreadyforconguraon.

WARNING!Applypoweronlyaerthedeviceisproperlywired.

1)Selectthemounnglocaon(duct,wall,panel).

2)Usethedeviceasatemplateandmarkthescrewholes.

3)Mountwithappropriatescrews.

Figure 1b - Mounng orientaon

Figure 1c - Applicaon connecons

24 V GND 0–10 V

Terminal block Terminal block for relays

NC COM NO NC COM NO

37.1

89.0

86.5

74.5

64.5

52.5

4.2

YES NO NO

Stac pressure Filter/Damper

monitoring

Fan/Blower

monitoring

Not

connected

STEP 2: WIRING DIAGRAMS CONFIGURATION CONTINUED

ForCEcompliance,aproperlygroundedshieldingcableisrequired.

1)Unscrewthestrainreliefandroutethecable(s).Useseparatestrain

reliefforthe0–10Voutputcableandtherelaycable(s).

2)Connectthewiresasshowningure2aand2b.

3)Tightenthestrainrelief.

Figure 2a - Wiring diagram 0–10 V output

Figure 2b - Wiring diagram relay(s)

STEP 3: CONFIGURATION

1)Selectthedesiredmeasurementunit.

2)Selectthedesiredmeasurementrange.

3)Selectthedesiredresponseme.

4)Conguretherelay(s).

5)Zerothedevice.

6)Calibratethespanpoint.

7)Connectthepressuretubes.Connectposivepressuretoport

labeled"+"andnegavepressuretoport"-".

Thedeviceisnowreadytobeused.

24 V

GND

P out

Power supply

24 VDC / 24 VAC

Output 0...10 V

SPAn

ZEro

rEL1/2

rESP

PSEL

UnIt

Pa, kPa, mmH2O, inchWC, mbar

Pressure range selecon

Response me

Relay menu(s)

Zero point calibraon

High point calibraon menu

rES

AdJ

High point calibraon

Reset high point calibraon

HYS

dir

Relay acvaon menu

Relay setpoint

Relay hysteresis 0–50 % of range

FALL

rISE

Relay acvaon on increasing pressure

Relay acvaon on decreasing pressure

COM

Relay 1

COM

Relay 2

With the MENU buon you can enter the menu by pressing the buon for

3 seconds. You can exit the menu without making any

changes.

With the BACK buon you can return without making changes.

With the OK buon you can open new opons or conﬁrm changes and return

to previous display.

With the buons you can scroll the menus.

NOTE! Always zero the device before use.

Tozerothedevicetwooponsareavailable:

1)Manualzeropointcalibraon

2)Autozerocalibraon

Does my transmier have an autozero calibraon? See the product

label.Ifitshows-AZinthemodelnumber,thenyouhavetheautozero

calibraon.

1)Manualzeropointcalibraon

NOTE:Supplyvoltagemustbeconnectedatleastone hourpriorto

zeropointadjustment.

a)Disconnectbothpressuretubesfromthepressureportslabeled+

and–.

b)Pushbotharrowbuonsontopofthelidshortlyorgoto

conguraonmenuandselect“Zero”.

c)Thezeroingofthedevicewillproceedautomacallywhenthe

greenledontopofthelidturnsoand“Zero”textfollowedby

 acounterfrom3to0secondsappearsonthedisplay.Thezeroing

iscompletewhenthegreenledturnsonagain.

d)ReinstallthepressuretubesensuringthattheHighpressuretube

isconnectedtotheportlabeled+,andtheLowpressuretubeis

connectedtotheportlabeled−.

NOTE:Thezeropointshouldbecalibratedviamanualzeropoint

calibraononehouraerinstallaonandatleastevery12months

duringnormaloperaons.

2)Autozerocalibraon

If the device includes the oponal autozero circuit, no acon is re-

quired.

Autozerocalibraon(-AZ)isanautozerofunconintheformofanauto-

maczeroingcircuitbuiltintothePCBboard.Theautozerocalibraon

electronicallyadjuststhetransmierzeroatpredeterminedmeinter-

vals(every 10minutes).Thefuncon eliminates all outputsignaldri

due to thermal, electronic or mechanical eects, as well as the need

fortechnicianstoremovehighandlowpressuretubeswhenperform-

ing inial or periodic transmier zero point calibraon. The autozero

adjustmenttakes4secondsaerwhichthedevicereturnstoitsnormal

measuring mode. Duringthe 4 secondadjustment period, the output

anddisplayvalueswillfreezetothelatestmeasuredvalue.

Transmiers equipped with the autozero calibraon are virtually

maintenancefree.

Thesellerisobligatedtoprovideawarrantyofveyearsforthedeliv-

eredgoodsregardingmaterialandmanufacturing.Thewarrantyperiod

isconsidered tostart on thedeliverydate of theproduct.If a defect

in raw materials ora producon aw is found,the seller is obligated,

whentheproductissenttothesellerwithoutdelayorbeforeexpira-

onofthewarranty,toamendthemistakeathis/herdiscreoneither

byrepairingthedefecveproductorbydeliveringfreeofchargetothe

buyeranewawlessproductandsendingittothebuyer.Deliverycosts

fortherepairunderwarrantywillbepaidbythebuyerandthereturn

costsbytheseller.Thewarrantydoesnotcomprisedamagescausedby

accident, lightning, ood or other natural phenomenon, normal wear

andtear,improperorcarelesshandling,abnormaluse,overloading,im-

properstorage,incorrectcareorreconstrucon,orchangesandinstal-

laonworknotdonebythesellerorhis/herauthorizedrepresentave.

Theseleconofmaterialsfordevicespronetocorrosionisthebuyer’s

responsibility,unlessotherwiseislegallyagreedupon.Shouldtheman-

ufactureralterthestructureofthedevice,thesellerisnotobligatedto

makecomparablechangestodevicesalreadypurchased.Appealingfor

warranty requiresthat the buyer has correctly fullled his/her dues

arisenfromthedeliveryandstatedinthecontract.Thesellerwillgive

anew warrantyforgoods thathavebeenreplacedorrepaired within

thewarranty,howeveronlytotheexpiraonoftheoriginalproduct’s

warrantyme.Thewarrantyincludestherepairofadefecvepartor

device, or if needed, a new part or device, but not installaon or ex-

change costs. Under no circumstance is the seller liable for damages

compensaonforindirectdamage.

RECYCLING/DISPOSAL

The parts le over from installaon should be

recycled according to your local instrucons.

Decommissioned devices should be taken to a

recyclingsitethatspecializesinelectronicwaste.

STEP 4: ZEROING THE DEVICE WARRANTY POLICY

Dieses Handbuch passt für folgende Modelle

Andere HK Instruments Relais Handbücher

HK Instruments

HK Instruments DPI Series Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung