Ohlins SD 047 Benutzerhandbuch

Steering damper for Yamaha R1/MT10

SD 047

Mounting Instructions

Note!1

Please note that there can be small differences

between your product and the images in

these instructions.

Note!1

Please note that during storage and transport,

especially at high ambient temperature, some

of the oil and grease used for assembly may

leak and stain the packaging. This will not cause

damage to the product, wipe off the excessive

oil or grease with a cloth.

Note!1

Before you install this product, check the kit

contents. If anything is missing, please contact

an Öhlins dealer.

Warning!⚠

Before you install this product, read the Öhlins

Owner’s manual. This product is an important

part of the vehicle and the vehicle stability.

Kit Contents

Description Part No Pcs

Steering damper SD 047 1

Tie-rap 4.8 x 200 00231-01 3

Washer 8.4/24/2 00426-03 2

Screw M8x40 01046-21 1

Sleeve 8/14/7 02238-16 1

Resistor 21702-02 1

Sticker Öhlins Wh/Tr 01185-01 2

Sticker Öhlins Bl/Tr 01185-04 2

Owner´s manual 07261-02 1

Instruction for R1:

Remove the mirrors.

Remove the inner panels below the handle

bars.

Remove the upper front fairing together with

screen.

Disconnect the original steering damper cable.

Connect the resistor (21702-02), supplied in

this kit.

Attach the resistor with the tie-raps provided.

Remove the panels under the lower triple

clamp.

Remove the original steering damper.

Continue on page 4.

MOUNTING INSTRUCTIONS

Warning!⚠

We strongly recommend to let an Öhlins dealer

install this product.

Warning!⚠

If you work with a lifted vehicle, make sure that it

is safely supported to prevent it from tipping over.

Note!1

When you work with this product, see the

vehicle service manual for vehicle specic

procedures and important data.

Note!1

Before you install this product clean the vehicle.

Resistor

Resistor cable

Resistor connection

Instruction for MT10:

Remove Right hand side “air intake cover” and

wiring cover.

Follow original steering damper wiring to

connector and disconnect it. Connect the

Ohlins Resistor (21702-02), supplied in this kit.

Attach the resistor with tie-raps provided.

Remove the original steering damper.

Continue on page 4.

MOUNTING INSTRUCTIONS

Common instruction

Install the Öhlins steering damper to the frame

bracket.

Install in this order:

1. Original screw

2. Washer (00426-03)

3. Original washer

4. Ball joint

5. Original rubber/steel washer (rubber egde

facing down)

6. Frame

Install the Öhlins steering damper to the triple

clamp.

Install in this order:

1. Screw (01046-21)

2. Washer (00426-03)

3. Ball joint

4. Sleeve (02238-16)

5. Triple clamp

6. Original nut

Install the removed parts in reverse order.

Turn the handle bars fully to the right and left to

make sure that nothing restricts the movement.

Install to the frame

Install to the triple clamp

This page intentionally left blank

MOUNTING INSTRUCTIONS

This page intentionally left blank

MOUNTING INSTRUCTIONS

This page intentionally left blank

MOUNTING INSTRUCTIONS

Öhlins Racing AB

Box 722

S-194 27 Upplands Väsby, Sweden

Phone +46 8 590 025 00

fax +46 8 590 025 80

reserved. Any reprinting or

unauthorized use without the written

permission of Öhlins Racing AB

is prohibited.

Öhlins products are subject to

continuous improvement and

development, therefore, although

these instructions include the most

up-to-date information available at

the time of printing, minor updates

may occur.

To nd the latest information

contact an Öhlins distributor.

Please contact Öhlins if you have

any questions regarding the

contents in this document.

SETUP DATA

Adjuster

knob

Warning!⚠

Before you ride/drive, always make sure that the

setup is according to the recommended setup

data. Read about adjustments and setting up

in the Öhlins Owner’s Manual before you make

any adjustments. Contact an Öhlins dealer if you

have any questions about setting up.

ADJUSTMENTS

Part no. MI_SD047_1

Issued 2020-11-16

Stroke 63 mm

Recommended setup 10 clicks

Andere Ohlins Motorradzubehör Handbücher

Ohlins

Ohlins KA 590 Bedienungsanleitung

Ohlins

Ohlins BM425 Bedienungsanleitung

Ohlins

Ohlins HO 404 Bedienungsanleitung

Ohlins

Ohlins YA919 Bedienungsanleitung

Ohlins

Ohlins BM 511 Bedienungsanleitung

Ohlins

Ohlins SD 168 Bedienungsanleitung

Ohlins

Ohlins PER 5U20 Bedienungsanleitung

Ohlins

Ohlins POF6H00 Bedienungsanleitung

Ohlins

Ohlins HO 519 Bedienungsanleitung

Ohlins

Ohlins SU717 Bedienungsanleitung

Ohlins

Ohlins SD 064 Bedienungsanleitung

Ohlins

Ohlins McPherson Strut MIR 1G00 Bedienungsanleitung

Ohlins

Ohlins suspension kit HOV 5A000 Bedienungsanleitung

Ohlins

Ohlins HO 403 Benutzerhandbuch

Ohlins

Ohlins BM 344 Bedienungsanleitung

Ohlins

Ohlins BM 701 Bedienungsanleitung

Ohlins

Ohlins BM335 Bedienungsanleitung

Ohlins

Ohlins SD195 Benutzerhandbuch

Ohlins

Ohlins SD 154 Bedienungsanleitung

Ohlins

Ohlins HO009 Bedienungsanleitung

Ohlins

Ohlins POF5H00 Bedienungsanleitung

Ohlins

Ohlins RS 562 Bedienungsanleitung

Ohlins

Ohlins YA 559 Bedienungsanleitung

Ohlins

Ohlins FCX 0302 Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung