76
TURNING OFF THE ALARM / SNOOZE OPERATION (Fig. 2)
The Freedom is equipped with gradual wake, which means that the alarm begins
soft and slowly gets louder. This will ensure a non-jarring wakeup.
• Press the Snooze bar for three seconds located on the top of the unit and the alarm
will sound again in nine minutes.
NOTE: You may only press the Snooze button during the Alarm mode for one hour
(7 times). After the seventh time, the alarm will turn off and will not sound again until
the next set time.
• To turn off the alarm, press any button on the top of the unit (except Snooze).
ONE DAY ALARM (HOTEL SETTING)
This alarm clock is equipped with a 1-Day Alarm feature, which allows the alarm to be set
for one day only. To activate this feature:
1. Turn unit over and loosen the 3 Phillips-head screws that hold the Stabiliazing Drawer
in place.
2. Pull Stabilizing Drawer forward and locate the switch marked HOTEL.
3. Move the HOTEL switch located on the bottom of the unit to the ON position. Once
this switch is in the ON position, the alarm time will need to be reset. Please see the
Setting and Using the Alarms section for instruction.
Please note:
• When the 1-Day alarm feature is activated, the alarm will only sound once. Once the
alarm is turned OFF, it will not sound again until the alarm is reset.
• When setting the alarm for a 1-Day alarm, you will be prompted to set the hour, minute,
and alarm source, but will NOT be prompted to set the EVERYDAY, WEEKDAYS, or
WEEKEND alarm as this feature will be disabled for both alarms.
iPAD/iPHONE/iPOD OPERATION (Fig. 2)
Please Note:
• If docking an iPad, be sure to pull out the Stabilizing Drawer on the back of the unit
to add stability when the iPad is docked.
• To avoid damage, do not force the device onto the Lightning docking pin.
WARNING: The dock connector is designed for Apple iPad, iPhone, and iPod
devices with a Lightning connector. Attempting to attach a non-iPad/iPhone/iPod
music player will damage or destroy your device and/or the product.
LISTENING TO MUSIC FROM YOUR iPAD/iPHONE/iPOD (Fig. 2)
1. Press the POWER button, located on top of the unit to turn ON.
2. Open the dock door and lift up the Lightning connector.
3. Fit iPad/iPod/iPhone carefully onto the Lightning connector.
4. Press POWER button ON.
5. Press the SOURCE button on the unit until the “iPhone” appears on the display.
6. Press the PLAY/PAUSE button on the unit to play and again to pause.
7. To skip forward and backward through tracks, press the Previous Track and Next
Track buttons on the unit.
8. To turn the unit OFF, press the POWER button. Note: For your convenience, your
device will continue charging on the dock while the unit is plugged in, even if the
power is turned off.
CHARGING YOUR APPLE DEVICE WHILE DOCKED
1. Ensure your Apple device is equipped with a Lightning pin connector.
NOTE: For Apple devices with a 30 pin connector, use the USB port on back of unit
to charge.
2. Fit the Apple device carefully onto the docking pin.
3. Once connected, your device will begin charging. To confirm, check the charging
indicator located in the upper right-hand corner of your device.
LISTENING TO A NON-DOCKING iPOD OR OTHER
PORTABLE AUDIO DEVICES (Fig. 2)
1. Plug the 3.5mm audio cable (included) into the device via the AUX input located on
the back of the unit.
2. Plug the other end of the audio cable into the AUX or headphone jack of the device.
3. Press the POWER button located on top of the dock.
4. Press the SOURCE button on the unit until the AUX icon appears on the display.
5. Press play on the connected device.
NOTE: You may need to adjust the volume on the device to achieve proper volume.
6. Press the POWER button to turn unit off.
NOTE: PLAY/PAUSE and TRACK FWD/BACK will not work with AUX input.
LISTENING TO THE RADIO (Fig. 1 & 2)
NOTE: For best reception, fully extend the wire antenna. DO NOT strip, alter or attach to
other antennas.
1. To listen to the radio, press the POWER button located on top of the unit.
2. Press the SOURCE button on the unit until a radio station appears on the display.
3. Use the FORWARD and REVERSE buttons on the top of the unit to select
desired station.
4. Press the POWER button to turn unit off.
TO SET/LISTEN TO STATION PRESETS (Fig. 2)
1. While in radio mode, use FORWARD and REVERSE buttons to select desired station.
2. Press the SET button on the top of the unit to add the station to your presets. Press
the PRESET button again to confirm.
3. To listen to station presets, press the PRESET button on the unit or the remote to
toggle through/select a preset station
