HMS Networks Intesis INMBSDAL1280200 Montageanleitung

This information is subject to change without notice

URL http://www.intesis.com

Rev.1.3

1 / 2

INMBSDAL1280200

DALI to Modbus Server gateway

Order Code: INMBSDAL1280200

Installation Sheet rev.1.3

HMS Industrial Networks S.L.U ©

SAFETY INSTRUCTIONS

!WARNING

Follow carefully this safety and installation instructions.

Improper work may lead to serious harmful for your health

and also may damage seriously the Intesis gateway and/or

any other equipment connected to it.

The Intesis gateway must be installed by accredited electrician or

similar technical personnel, following all the safety instructions given

here and in accordance always with the country legislation for

installation of electric equipment.

The Intesis gateway cannot be installed outdoors or exposed to direct

solar radiation, water, high relative humidity or dust.

The Intesis gateway must only be installed in a restricted access

location.

In case of wall mount, fix firmly the Intesis gateway on a not vibrating

surface following the instructions next.

In case of DIN rail mount fix the Intesis device properly to the DIN rail

following the instructions below.

Mounting on DIN rail inside a metallic cabinet properly connected to

earth is recommended.

Disconnect always power of any wires before manipulating and

connecting them to the Intesis device.

A power supply with an NEC Class 2 or Limited Power Source (LPS)

and SELV rated is to be used.

Respect always the expected polarity of power and communication

cables when connecting them to the Intesis gateway.

Supply always a correct voltage to power the Intesis gateway, see

details of voltage range admitted by the device in the technical

characteristics below.

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.

Dispose of Used Batteries according to the instructions. Battery

replacement shall be done by an authorized installer.

CAUTION: The device is to be connected only to networks without

routing to the outside plant, all communication ports are considered for

indoor only.

This device was designed for installation in an enclosure. To avoid

electrostatic discharge to the unit in environments with static levels

above 4 kV, precautions should be taken when the device is mounted

outside an enclosure. When working in an enclosure (ex. making

adjustments, setting switches etc.) typical anti-static precautions

should be observed before touching the unit.

Safety instructions in other languages can be found at:

https://intesis.com/docs/manuals/v6-safety

INSTALLATION

Follow instructions next to properly install the gateway.

Disconnect from mains the power supply before connecting it to the

Intesis device.

Disconnect power of any bus or communication cable before

connecting it to the Intesis gateway.

Mount the Intesis device on the wall or DIN rail following the instruction

given below, respecting the safety instructions given above.

Connect a NEC Class 2 or Limited Power Source (LPS) and SELV

rated power supply to the Intesis device, respect the polarity if DC

power or Line and Neutral if AC power. Apply always a voltage within

the range admitted by the Intesis device and of enough power (see

technical characteristics).

Circuit-breaker must be used before the power supply. Rating 250V-

6A.

Connect the communication cables to the Intesis gateway, see details

on the user's manual.

Power the Intesis gateway and the rest of devices connected to it.

Wall Mount

1. Separate the fixing clips in the bottom of the box, pushing

them to the outside until hear the "click" which indicates that

now the clips are in position for wall mount, see in the figure

below.

2. Use the holes of the clips to fix the box in the wall using

screws. Use the template below for the wall wholes.

Clips in their original position Clips in position for wall mount

(for DIN rail mount)

DIN Rail Mount

With the clips of the box in their original position, insert first the box

in the upper edge of the DIN rail and later insert the box in the

down part of the rail, using a small screwdriver and following the

steps in the figure below.

Press

DIN Rail

CONFIGURATION

Use the Configuration Tool to configure the gateway.

See instructions to download and install the latest version at:

https://intesis.com/docs/software/intesis-maps-installer

Use the Ethernet connection or the Console Port (mini USB type B

connector included) for communication between the gateway and the

configuration tool. See CONNECTIONS below and follow instructions

of user’s manual for more details.

Owner’s Record

The serial number is located at the rear of the gateway.

Record this information in the space provided below.

Refer to it whenever you contact upon your gateway

dealer or support team regarding this product.

Serial No.

This information is subject to change without notice

URL http://www.intesis.com

Rev.1.3

2 / 2

Enclosure

Plastic, type PC (UL 94 V-0)

Net dimensions (dxwxh): 90x88x56 mm

Recommended space for installation (dxwxh): 130x100x100mm

Color: Light Grey. RAL 7035

Battery

Size: Coin 20mm x 3.2mm

Capacity: 3V / 225mAh

Type: Manganese Dioxide Lithium

Mounting

Wall.

DIN rail EN60715 TH35.

Console

Port

Mini Type-B USB 2.0 compliant

1500VDC isolation

Terminal Wiring

(for power supply and

low-voltage signals)

Per terminal: solid wires or stranded wires (twisted or with

ferrule)

1 core: 0.5mm2… 2.5mm2

2 cores: 0.5mm2… 1.5mm2

3 cores: not permitted

USB port

Type-A USB 2.0 compliant

Only for USB flash storage device (USB pen

drive)

Power consumption limited to 150mA (HDD

connection not allowed)

Power

1 x Plug-in screw terminal block (3 poles)

Positive, Negative, Earth

24VDC +/-10%

Push Button

Button A: Check the user manual

Button B: Check the user manual

Operation

Temperature

0°C to +50°C

Ethernet

1 x Ethernet 10/100 Mbps RJ45

2 x Ethernet LED: port link and activity

Operational

Humidity

5 to 95%, no condensation

Port A

1 x DALI port (Plug-in screw terminal block orange 2 poles)

1500VDC isolation from other ports

DALI guaranteed power: 235mA

DALI maximum power 250 mA

Voltage rating: 16VDC

1 x Plug-in screw terminal block green (2 poles)

Reserved for future use

Protection

IP20 (IEC60529)

LED

Indicators

10 x On board LED indicators

2 x Error (red) / Power LED

2 x Ethernet Link / Speed

2 x Port A TX/RX

2 x Port B TX/RX

1 x Button A indicator

1 x Button B indicator

Switch A

(SWA)

1 x DIP-Switch for PORT A configuration:

Reserved for future use

PORT B

1 x DALI port (Plug-in screw terminal block green 2 poles)

1500VDC isolation from other ports

DALI guaranteed power: 235mA

DALI maximum power 250 mA

Voltage rating: 16VDC

Switch B

(SWB)

1 x DIP-Switch for PORT B configuration:

Reserved for future use

CONNECTIONS

ELECTRICAL & MECHANICAL FEATURES

Power Supply

Must use NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply. Respect polarity

applied of terminals (+) and (-). Be sure the voltage applied is within the range admitted (check table

below). The power supply can be connected to earth but only through the negative terminal, never

through the positive terminal.

Ethernet / Modbus TCP / Console (UDP & TCP)

Connect the cable coming from the IP network to the connector ETH of the gateway. Use an Ethernet

CAT5 cable. If communicating through the LAN of the building, contact the network administrator and

make sure traffic on the port used is allowed through all the LAN path (check the gateway user manual

for more information). With factory settings, after powering up the gateway, DHCP will be enabled for 30

seconds. After that time, if no IP is provided by a DHCP server, the default IP 192.168.100.246 will be

set.

PortA / DALI A

Connect the DALI bus to connectors A3 (DA+) A4 (DA-) of gateway’s PortA. The Intesis gateway

provides 16VDC (+/-2%) DALI voltage to the bus.

PortB / DALI B

Connect the DALI bus to connectors B1 (DA-) B2 (DA+) of gateway’s PortB. The Intesis gateway

provides 16VDC (+/-2%) DALI voltage to the bus.

Console Port

Connect a mini-type B USB cable from your computer to the gateway to allow communication between

the Configuration Software and the gateway. Remember that Ethernet connection is also allowed. Check

the user manual for more information.

USB

Connect a USB storage device (not a HDD) if required. Check the user manual for more information.

Port B

USB

EIA 232

B1 B2 B3

SW B

SW A

Ethernet Port

Port A

A1 A2

A3 A4

Power

zzzzz

Run / Error

Eth.Link/Spd

PortA TX/RX

PortB TX/RX

Button A

Button B

Console

- +

Power Supply

DALI A

Ethernet

Modbus TCP

USB

storage

(not used)

DALI B

Console

Port

100 mm (h)

100 mm (w)

130 mm (d)

This marking on the product, accessories, packaging or literature (manual) indicates that the product contains electronic

parts and they must be properly disposed of by following the instructions at https://intesis.com/weee-regulation

Andere HMS Networks Tor Handbücher

HMS Networks

HMS Networks Intesis INKNXSAM O000 Series Montageanleitung

HMS Networks

HMS Networks Intesis Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770HIS00 O000 Series Montageanleitung

HMS Networks

HMS Networks Intesis IN775FGL00 O000 Series Bedienungsanleitung

HMS Networks

HMS Networks Ixxat SG-gateway Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN776MHI00 O000 Series Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00 O000 Series Bedienungsanleitung

HMS Networks

HMS Networks Intesis INBACMEB 0000 Series Montageanleitung

HMS Networks

HMS Networks Intesis IN770AIR00 O000 Series Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN776MHI00 O000 Series Montageanleitung

HMS Networks

HMS Networks Intesis IN770PAN00 O000 Series Montageanleitung

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00 O000 Series Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN703DAL0640000 Bedienungsanleitung

HMS Networks

HMS Networks Ewon Cosy 131 Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN770AIR00 O000 Series Bedienungsanleitung

HMS Networks

HMS Networks Intesis IN775FGL00 O000 Series Montageanleitung

HMS Networks

HMS Networks Ewon Netbiter EC300 Series Benutzerhandbuch

HMS Networks

HMS Networks Ewon Netbiter EC300 Series Bedienungsanleitung

HMS Networks

HMS Networks Intesis INBACDAL1280200 Montageanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung