HMS Anybus Bedienungsanleitung
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
How to configure an Anybus EtherNet/IP
Scanner module with RSNetWorx for
EtherNet/IP
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 1 (20)
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 2 (20)
More info about the network and products
This document gives a brief description of how to configure an Anybus Scanner product for EtherNet/IP. For
further information about the products, please consult the HMS homepage, www.anybus.com. The latest
manuals, EDS-files etcetera can be downloaded from that location.
For more information concerning the EtherNet/IP network the Open EtherNet/IP Vendor Organization has a
homepage. Please visit, www.odva.org, for more information about EtherNet/IP.
Document history
Revision Date Description Responsible
1.00 2007-10-17 Created Thorbjörn Palm
1.01 2007-12-14 Minor revision Thorbjörn Palm
1.02 2008-01-10 Minor correction Thorbjörn Palm
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 3 (20)
Contents
1. Solution overview .....................................................................................................................................4
2. Applicable Anybus products ...................................................................................................................5
3. Requirements............................................................................................................................................5
4. Anybus configuration...............................................................................................................................6
4.1. IP settings..........................................................................................................................................6
4.2. Anybus-M and Anybus PCI-card configuration...............................................................................7
4.3. Anybus X-gateway configuration.....................................................................................................8
5. EtherNet/IP configuration.....................................................................................................................10
5.1. Configuring the Ethernet driver......................................................................................................10
5.2. EtherNet/IP network configuration.................................................................................................12
6. Testing.....................................................................................................................................................19
6.1. X-gateway.......................................................................................................................................19
6.2. Monitoring the EtherNet/IP network ..............................................................................................20
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
1. Solution overview
This application note describes how to configure an Anybus EtherNet/IP Scanner module and how to set up
the EtherNet/IP network using RSNetWorx. Below you can find an overview of the system described in this
document. Other nodes may be attached to the network, but are not necessary.
The configuration is described in two steps.
1. At first the Anybus Scanner module configuration is explained.
2. Secondly the configuration of the EtherNet/IP network is described.
Note: This document is valid for all Anybus EtherNet/IP Scanner products, however sections written in
italics describe the configuration of a specific product.
The contents describe step by step how a configuration is done. This document assumes the reader is familiar
with industrial communication, EtherNet/IP networks and HMS PCI-card and X-gateway.
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 4 (20)
Figure 1 Hardware connection overview.
EtherNet/IP
Modbus-TCP
Anybus X-gateway
Other network
i.e. Modbus-TCP
EtherNet/IP
Scanner
Anybus Communicator
EtherNet/IP Adapter
PC
Client PC
EtherNet/IP
Anybus PCI card
Client
Anybus Communicator
EtherNet/IP Adapter
PC
EtherNet/IP Scanner
PC
ModScan
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 5 (20)
2. Applicable Anybus products
The following table specifies the relevant Anybus products for this document.
Description Name / Type
Anybus X-gateway Scanner EtherNet/IP
Anybus PCI Scanner EtherNet/IP
Anybus-M Scanner EtherNet/IP
3. Requirements
The following equipment is needed to setup a successful configuration. Note that RSNetWorx for
EtherNet/IP is licensed Rockwell Automation software.
Description Name / Type Version
Microsoft Windows terminal software HyperTerminal 5.1
X-gateway Interface Addendum Anybus X-gateway EtherNet/IP
Scanner Interface Addendum 1.00
X-gateway User Manual X-gateway User Manual 1.11
Anybus-M Fieldbus Appendix Fieldbus Appendix Anybus-M
EtherNet/IP 1.02
EtherNet/IP network configuration software RSNetWorx for EtherNet/IP 8.00.00 (CPR 7)
EtherNet/IP driver configuration software RSLinx Classic Lite 2.51.00.21
(CPR 7)
Ethernet monitoring software
(Optional software for monitoring)
Wireshark 0.99.6a
Power supply 24VDC n.a. n.a
Configuration cables n.a. n.a.
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
4. Anybus configuration
The first step is to configure the Anybus Scanner module. The configuration of the IP-settings is described in
the following chapter. In the two following chapters the configuration of the Anybus-M, Anybus PCI-card
and X-gateway are explained.
4.1. IP settings
Make sure each node on the network has a unique IP address. The IP settings of the Anybus EtherNet/IP
modules can be configured in various ways. In many industrial applications DHCP with a fixed MACID
table is used. For the Anybus Ethernet modules DHCP is activated by default.
In other cases it is recommended to use the Anybus IPconfig tool for configuring the IP-settings. The
Anybus IPconfig tool can be used to configure the IP settings of all Anybus EtherNet/IP modules. The
program can be downloaded at HMS website1. Start the program and the main window will be opened.
Figure 2 The Anybus IPconfig tool.
The program scans the network for Anybus Ethernet modules. The settings can be configured manually or
the DHCP function can be used. To change the settings manually, double click on the module of interest and
enter the desired IP-settings.
Using DHCP disables the manual IP-settings
In this case make sure the DIP-switches are
set in zero position.
Figure 3 Configuring the IP settings.
1www.anybus.com
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 6 (20)
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 7 (20)
As mentioned before there are other ways to configure the IP settings. The IP settings can also be configured
by gleaning or using the web interface in the module. See the notes below for additional product specific
information.
Note for the Anybus-M Scanner:
DIP switches 1-8 set the last part of the IP address, 192.168.0.xxx. The switches will be found next to the
indication LEDs. The modules can also be configured by mailbox commands or by the ethcfg.cfg
configuration file.
Note for the X-gateway:
The X-gateway can also be configured by the DIP switches as described above or by the ethcfg.cfg
configuration file.
Note for the Anybus PCI card:
The PCI-card can also be configured by mailbox commands or by the ethcfg.cfg configuration file.
For further instructions see the respective manual or appendix.
4.2. Anybus-M and Anybus PCI-card configuration
The Anybus-M and the Anybus PCI card are configured via the host application interface using the mailbox
interface. Refer to the Anybus-M Fieldbus Appendix and the Anybus API reference manual for details.
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
4.3. Anybus X-gateway configuration
Use the HyperTerminal on a PC to configure the X-gateway. Connect a serial cable between the PC and the
config port on the X-gateway. Start the HyperTerminal and open the “File” menu and click on new, choose
the desired COM port and then click on OK. The following window will appear.
Figure 4 Configuring the connection in the HyperTerminal.
Make sure the settings are identical to those shown in the window above. Alternatively download a
HyperTerminal session file from the HMS website2, double click on it and select COM port.
Connect and press ESC and the following menu will appear.
Figure 5 Anybus X-gateway Main menu.
Press 6 and enter the desired configuration.
2www.anybus.com
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 8 (20)
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
The figure below shows an example; in this case an EtherNet/IP Scanner to EtherNet/IP Adapter X-gateway
is used and 20 bytes of I/O data is configured.
Figure 6 The X-gateway configuration.
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 9 (20)
How to configure an Anybus EtherNet/IP Scanner module with RSNetWorx for EtherNet/IP
SCM-7032-031
Rev 1.02
5. EtherNet/IP configuration
To configure the EtherNet/IP network the tools RSNetWorx for EtherNet/IP and RSLinx are used. Firstly the
Ethernet Driver needs to be configured in RSLinx and secondly the EtherNet/IP network is configured by
RSNetWorx.
5.1. Configuring the Ethernet driver
Start the RSLinx software from Rockwell. Open the Communications menu and select Configure Drivers.
Figure 7 Opening the Configure Drivers menu.
In the following window select Ethernet/IP Driver and then click on Add Newn.
1
Figure 8 Adding a new Ethernet device.
Saved: 2008-01-10
Filename: How to configure an Anybus EtherNetIP Scanner (6).doc HMS Industrial Networks AB
Page 10 (20)
Andere Handbücher für Anybus
8
Inhaltsverzeichnis
Andere HMS Steuereinheit Handbücher
HMS
HMS Anybus CC-Link Slave Einrichtungshandbuch
HMS
HMS Anybus AS-Interface Master Bedienungsanleitung
HMS
HMS Ixxat USB-to-CANV2 Bedienungsanleitung
HMS
HMS Anybus CompactCom 30 Leitfaden
HMS
HMS CM CANopen Bedienungsanleitung
HMS
HMS Anybus CANopen Slave Bedienungsanleitung
HMS
HMS Ewon Flexy FLB 3205 Bedienungsanleitung
HMS
HMS Anybus Communicator Bedienungsanleitung
HMS
HMS IXXAT Safe T100 Installations- und Betriebsanleitung
HMS
HMS Anybus EtherNet/IP Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
