HMS Anybus X-gateway IIoT Benutzerhandbuch

IIoT

Anybus®X-gateway™Network Interface

STARTUP GUIDE

SP2443 1.0 en-US ENGLISH

Important User Information

Liability

Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB

of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We,

HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous

product development. The information in this document is subject to change without notice and should not

be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no

responsibility for any errors that may appear in this document.

There are many applications of this product. Those responsible for the use of this device must ensure that

all the necessary steps have been taken to verify that the applications meet all performance and safety

requirements including any applicable laws, regulations, codes, and standards.

HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems

that may arise as a result from the use of undocumented features, timing, or functional side effects found

outside the documented scope of this product. The effects caused by any direct or indirect use of such

aspects of the product are undefined, and may include e.g. compatibility issues and stability issues.

The examples and illustrations in this document are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular implementation, HMS Industrial Networks

AB cannot assume responsibility for actual use based on these examples and illustrations.

Intellectual Property Rights

HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product

described in this document. These intellectual property rights may include patents and pending patent

applications in the USA and other countries.

Anybus®is a registered trademark of HMS Industrial Networks AB. All other trademarks mentioned in this

document are the property of their respective holders.

IIoT Startup Guide SP2443 1.0 en-US

Preface 3 (8)

1 Preface

1.1 About This Document

This document describes how to install the Anybus X-gateway IIoT Interface.

For additional documentation and software downloads, FAQs, troubleshooting

guides and technical support, please visit www.anybus.com/support.

1.2 Document Conventions

The following formatting conventions are used in this document to indicate safety

information and other content of specific importance:

WARNING

This instruction must be followed to avoid a risk of death or serious injury.

Caution

This instruction must be followed to avoid a risk of personal injury.

This instruction must be followed to avoid a risk of reduced functionality

and/or damage to the equipment, or to avoid a network security risk.

This is additional information which may facilitate installation and/or

operation.

IIoT Startup Guide SP2443 1.0 en-US

Description 4 (8)

2 Description

2.1 Connectors

This product contains parts that can be damaged by electrostatic

discharge (ESD). Use ESD prevention measures to avoid damage.

Fig. 1 IIoT interface

Ethernet Connectors

The IIoT interface contains a dual port Ethernet switch with RJ45 type

connectors. The two Ehernet ports are labeled X1.1 and X1.2 if the interface is

top-mounted, and X2.1 and X2.2 if the interface is bottom-mounted.

Pin Signal Description

1 TD+ Transmit data +

2 TD- Transmit data -

3 RD+ Receive data +

4 - (reserved)

5 - (reserved)

6 RD- Receive data -

7 - (reserved)

8 - (reserved)

IIoT Startup Guide SP2443 1.0 en-US

Description 5 (8)

2.2 LED Indicators

Fig. 2 IIoT interface LED indicators

The GW Status LED indicates operation status for the X-gateway. The other

LEDs indicate network communication and status for the IIoT interface.

LED Indication Meaning

GW Status

Off No power

Green Gateway running

Red Communication error

Red, flashing Network interface error

LINK/ACT

Off Link not detected or no power

Green Link established (100 Mbit/s)

Green, flickering Link activity (100 Mbit/s)

Red Link established (10 Mbit/s)

Red, flickering Link activity (10 Mbit/s)

Off Offline or no power

Green Online, IP address assigned

Green, flashing Online, no IP address assigned

Red Fatal error, IP address conflict

Alternating Red/Green Firmware update in progress

Off No power

Green Normal operation

Red Fatal error

Alternating Red/Green Firmware update in progress

The LINK/ACT LED indicators will show a red light for 10 Mbit/s connections.

This is normal and does not indicate an error.

The NS and MS LED indicators may flash green/red briefly during the startup

self-test sequence. This is normal and does not indicate an error.

IIoT Startup Guide SP2443 1.0 en-US

Installation 6 (8)

3 Installation

3.1 Installation Overview

Prerequisites

The following items are required for installation and basic configuration:

• Ethernet cable

• USB cable

• Anybus Configuration Manager - X-gateway (1.5.1.1 or later)

• Anybus Configuration Manager - IIoT

• IPconfig (3.2.1.1 or later)

The Anybus Configuration Manager and IPconfig applications can be

downloaded from www.anybus.com/support.

Basic installation steps

1. Connect the Anybus X-gateway IIoT Interface to the Ethernet network.

2. Connect a computer to the USB connector on the X-gateway.

3. Power on the X-gateway.

4. Use IPconfig to configure the TCP/IP settings for the IIoT interface.

5. Use Anybus Configuration Manager - X-gateway to configure the data

exchange options for the two interfaces in the Anybus X-gateway.

6. Use Anybus Configuration Manager - IIoT to create a tag configuration and

transfer it to the IIoT interface.

7. Connect to the web interface of the IIoT interface and configure MQTT/OPC

UA communication.

IIoT Startup Guide SP2443 1.0 en-US

This page intentionally left blank

last page

Box 4126

300 04 Halmstad, Sweden

[email protected] SP2443 1.0 en-US / 2018-10-29 / 10374

Inhaltsverzeichnis

Andere HMS Aufnahmegeräte Handbücher

HMS

HMS AnyBus-PCI Profibus DPV1 Slave Handbuch

HMS

HMS IXXAT FlexRay Betriebsanleitung

HMS

HMS AnyBus DataTransfer Leitfaden

HMS

HMS Intesis INMBSMID I000 Series Bedienungsanleitung

HMS

HMS Anybus X-gateway PROFIBUS Montage- und Wartungsanleitung

HMS

HMS Ixxat PCIe/104 Series Bedienungsanleitung

HMS

HMS IXXAT iPC-I 320/PCI II Bedienungsanleitung

HMS

HMS Ixxat iPC-I 320 Bedienungsanleitung

HMS

HMS Anybus CompactCom B40-1 Leitfaden

HMS

HMS Intesis INMBSDAI001I000 Bedienungsanleitung

HMS

HMS EtherCAT Slave Montage- und Bedienungsanleitung

HMS

HMS Intesis INBACDAI001I100 Bedienungsanleitung

HMS

HMS Intesis IN485UNI001I000 Bedienungsanleitung

HMS

HMS Ixxat CAN-IB Series Bedienungsanleitung

HMS

HMS INTESIS INMBSPAN001A000 Bedienungsanleitung

HMS

HMS Ixxat CAN-IB XMC Series Bedienungsanleitung

HMS

HMS IXXAT iPC-I XC16/PCIe Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch