Holmatro SMC 4006 Technische Daten

SMC 4006 / 4006 C 01D19

Repair & Maintenance

instructions Rescue equipment

Maintenance recommendations after use (every time)

Wear full protective gear during maintenance !

Always act according to the safety instructions as supplied with each tool !

Contact the Holmatro dealer if one of the items does not work properly !

•Necessary equipment: see check list page 12.

Left: SMC 4006 Right: SMC 4006 C

Step 1

•Check the cutter for completeness, oil leaks

and damage. Do not use the cutter if it leaks

or is damaged, and contact the Holmatro

dealer.

•Check general condition of the cutter.

Clean/dry the tool with soft cloth.

•Check the attachment of the carrying handle.

If necessary, fasten it firmly by tightening the

wing screw.

Step 2

•Check coupler(s) and dust cap(s) for damage,

dirt and/or oil leakage.

•Clean coupler(s) with a clean and soft cloth, if

necessary with water and soap.

•If necessary grease with hydraulic oil or use

WD-40.

•Check functioning coupler(s) (see page 13).

•Reconnect loose dust cap(s) to coupler(s).

Step 3

•Check the functioning of the control handle, it

must automatically return to it’s neutral

position.

•Contact the Holmatro dealer if the handle

does not work properly.

Step 4 (only for pigtail connection)

•Check the back of the control handle for oil,

this will indicate that the safety valve has been

activated during use (return line of the tool

was not connected properly to the returnline of

the pump).

•Clean the deadman’s handle internally by

blowing compressed air in the back of the

handle.

•Check the hose for damage.

While the greatest care has been devoted to the content, it is

possible that the information in this printed matter is incorrect

or incomplete. Holmatro N.V. and its affiliated companies

(hereafter: Holmatro) cannot be held liable in any way for the

consequences of activities undertaken on the

basis of this

printed matter. If you have any doubts about the correctness

or completeness of the information, you shall contact

Holmatro (phone number: +31 (0)162-589200).

Nothing from this printed matter can be copied and/or made

public in any way witho

ut the explicit authorisation of

Holmatro.

Manufacturing sales & service Manufacturing sales & service

worldwide U.S.A., Canada and Latin America

Holmatro Rescue Equipment B.V. Holmatro, Inc.

P.O. Box 33, 4940 AA Raamsdonksveer 505 McCormick Drive, Glen Burnie, MD

The Netherlands 21061 U.S.A

T+ 31 (0)162 - 58 92 00 T+ 1 - 410 - 768 - 9662

F+ 31 (0)162 - 52 24 82 F+ 1 - 410 - 768 - 4878

E[email protected] Einfo@holmatro-usa.com

www.holmatro.com www.holmatro-usa.com

Pigtail

connection

only !

1 - 3

SMC 4006 / 4006 C 01D19

Repair & Maintenance

instructions Rescue equipment

Maintenance recommendations after use, continued

Step 5

•Check the presence of the lock-nut.

•Check if the upper moving part can move

freely. If not see page 8 step 9 to adjust.

Step 6

•Clean the blades after use.

•Check the blades for damage, remove

upsettings on the blades. Use a file and

abrasive paper.

•Blades can be turned one time 120°.

•Replace, or turn blades 120° when blades are

damaged.

•See page 7 “replacing the blades” to replace

the blades.

•Lubricate the blades after use with

preservative oil WD-40.

Step 7

•Check the presence of both locking screws.

•Both lock bolts should be tightened firmly.

Step 8

•The best cutting results are obtained if the

blades (jaw opening) are open 0.5 mm to 1

mm at the end of the cutting movement.

•See page 9 “Adjusting the plunger stroke” to

adjust the plunger stroke.

Step 9

•Spray Teflon lubricating oil on and between

the moving parts of the centre bolt B while the

tool is opening and closing (cover not shown).

Step 10

•Clean/dry the tool with soft cloth before

storing it.

•Lightly oil steel parts with preservative oil

WD-40.

•Store the cutter in a dry and well-ventilated

area.

•Do not fully close the cutter, always keep a

few mm for opening, so that the tool can be

stored without pressure.

0.5-1.0mm

2 - 3

SMC 4006 / 4006 C 01D19

Repair & Maintenance

instructions Rescue equipment

Monthly maintenance recommendations (or after 10 hours of use)

Wear full protective gear during maintenance !

Always act according to the safety instructions as supplied with each tool !

Contact the Holmatro dealer if one of the items does not work properly !

•Necessary equipment: see check list page 12.

Left: SMC 4006 Right: SMC 4006 C

Step 1

•Check the operation of the tool by opening

and closing the cutter 2 times.

•No cracking sounds can be heard.

•Check the tool for damage and leaking. If the

tool doesn’t work properly and/or leaks,

contact the Holmatro dealer.

Step 2

•Check coupler(s) and dust cap(s) for damage,

dirt and/or oil leakage.

•Clean coupler(s) with a clean and soft cloth, if

necessary with water and soap.

•If necessary grease with hydraulic oil or use

WD-40.

•Check functioning coupler(s) (see page 13).

•Reconnect loose dust cap(s) to coupler(s).

Step 3

•Check whether the deadman’s handle returns

to it’s neutral position.

•Check the operation of the deadman’s handle.

Have the Holmatro dealer repair the

deadman’s handle if it doesn’t function

properly.

Step 4 (only for tools with pigtail hoses)

•Check pigtail hose(s) and mounting of the

couplers.

•Replace the pigtail hose when:

odamages are visible

othe steel inner layer is visible

oblisters are visible

oobvious traces of kinks are visible

ocuts are visible

oprotection spring is not mounted well

Step 5

•Check the presence of the lock-nut.

Check if the upper moving part can move

freely.

•If not, see page 8 step 9.

Step 6

•Check the carrying handle for damage.

Replace a damaged carrying handle.

•Check the attachment of the carrying handle.

If necessary, fasten it firmly by tightening the

wing screw.

3 - 3

Dieses Handbuch passt für folgende Modelle

Andere Holmatro Cutter Handbücher

Holmatro

Holmatro PCU Bedienungsanleitung

Holmatro

Holmatro BCU 05 A Series Bedienungsanleitung

Holmatro

Holmatro GCU 50 i EVO 3 Series Bedienungsanleitung

Holmatro

Holmatro GSP 52 EVO 3 Series Bedienungsanleitung

Holmatro

Holmatro HMC 8 U Bedienungsanleitung

Holmatro

Holmatro BCU 05 A Series Bedienungsanleitung

Holmatro

Holmatro CU 4007 Bedienungsanleitung

Holmatro

Holmatro PCT50 Bedienungsanleitung

Holmatro

Holmatro HCT5111 Series Bedienungsanleitung

Holmatro

Holmatro PCU50 Bedienungsanleitung

Holmatro

Holmatro GCT 51 EVO 3 Series Bedienungsanleitung

Holmatro

Holmatro CU 4007 C Bedienungsanleitung

Holmatro

Holmatro HCT5111 Series Bedienungsanleitung

Holmatro

Holmatro CCU10 Bedienungsanleitung

Holmatro

Holmatro CU 5040 GP Bedienungsanleitung

Holmatro

Holmatro SMC 5008 (ST) Bedienungsanleitung

Holmatro

Holmatro Core SMC 5006 Bedienungsanleitung

Holmatro

Holmatro GCT 51 EVO 3 Series Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

Makita

Makita DCS552 Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung