HOLOVISION 400-A-TES2 Bedienungsanleitung
Manual Type 6.5.0.7-RF
TE 2
with Essex “A CII” Keypad
For Models
400-A-TES2 401-A-TES2
403-A-TES2 404-A-TES2
410-A-TES2 411-A-TES2
pecifications
IN TALLATION
IN TRUCTION
501 E. Goetz Ave.
anta Ana, Ca 92707
www.eholovision.com
Ph. 714-434-6904
Fax 800-362-0002
HOLOVI ION
Access Control
Essex K1-26I Keypad field configurable to ASCII,
Wiegand and others.
TES2 can open 2 doors with optional T-RLY
400 Series ‘’A’’ Junction Board
ot Used
12 VDC input (for camera and keypad)
Connect tamper switch to alarm (optional)
Intercom to TES2 (Polarity sensitive)
Bit Parity Mode
Inverted Serial
Ground
ormal Serial
Communication
TES2 telephone entry system provides a
communication link between the front door and every
phone in the house. When the button is pressed, the
phones in the house will ring with a distinctive ring.
The home owner can then speak to the visitor by answer-
ing any of the ringing phones in the House. TES2 is a 2
door system (front door, back door).
Page 2 Type 6.5.0.7-RF
A CII Connection to Crestron or HAI 400
O COM C O COM C
Red Green LED control Gate Control
Automation System Relays
(Typical of Crestron or HAI)
To gatecontrol
HAI
To Automation System
(see details below)
Crestron
Black to pin 5
White to pin 2
Crestron Serial Port
Z1
----
Z2 Z3 Z4 Z5
GRD 12V Switched
12V AUX
24VAC
- - -
To HAI serial port:
RJ-11 Black = pin 1 White = pin 4 (RJ-11 is 4 pin)
RJ-25 Black = pin 2 White = pin 5 (RJ-25 is 6 pin)
Black
Black to “Grnd”
White
Viewed with ‘’tit’’ up
Black
Green
The red LED is normally on all of the
time. When a valid code is entered, the
relay controlling the LEDs would close,
and the green light would go on
(momentarily). ote, this relay must be
programmed in Crestron or HAI in order
for this to take place.
K1-26I
ASCII Keypad
12vDC
1.5A
Connection is Polarity ensitive
o Ring Jumper
..
C1 C O1 C2 C O2
T-RelayBoard(optional)
Door 1 Door 2
J6
Page 3 TYPE 6.5.0.7-RF
For Camera
To Automation System
To Automation System Relay O & COM
12vDC
1.5A
OTE: Voltage from telephones is not necessary for
the system to work. (See note ‘‘No CO operation”)
The connection between the main board and the
speaker board is polarity sensitive.
CO
Line
In
To
House
Phones
Door
2
Door
1
T1 R1 T2 R2
.... ..
o Co Jumper
Use jumper in exernal
phone line is not used
J3 J4
House
Telephones
1 The “NO RING” option is to be used if external door chimes are being used in the house, and the phones should not ring when the
door bell button is pushed. When the “NO RING” option is selected, the phones will not ring. When the homeowner hears the
external door chime (not supplied by Holovision), and then picks up any telephone, they will be automatically connected to the door
phone. o additional buttons need to be pushed. The door call will be available for 10 seconds after the button is pushed.
After 10 seconds, follow the instructions shown for “Basic Operation of TE 2”.
2 For “NO RING” option, install jumper pin (J6) on far right side of board. TES2 is shipped with this option disabled.
3 In order to connect door chimes and TES2, a double pole button must be used. The double pole button (Part number 9202) is
available from holovision.
et “No Ring” Option (TES2 is shipped with this option DI ABLED)
tep Action
1 For “NO CO” option is to be used if there is no CO (Central Office) line to the home. The o CO option would be used if the
homeowners used cell phone only (no house phone line). In this case, several phones would be required throughout the house. These
phones would be used only for answering door phone calls.
2 For “NO CO” option, install 2 jumper pins if (J3, J4) at th bottom of the board. TES2 is shipped with this option disabled.
et “No CO Line” Option (TES2 is shipped with this option DI ABLED)
tep Action
1 The relay board is equipped with screw terminals. This has connections for each relay in normally open (“NO”) and
normally closed (“NC”) options.
2 Attach to either O or C connectors. If a second gate is being used, also connect it to O or C connectors.
Connect Gate trike Relay
tep Action
TE 2 Telephone Entry ystem
1 Mount the main board near the telephone distribution center of the house and attach the telephone line from the service provider to the
connection labeled “LINE TO DEMARC”.
2 Connect the house phone distribution system to the wire terminals labeled “HOU E PHONE”.
3 Punch down “ONE” and “TWO” door stations. If only one door station is being used, it should be connected on the “ONE” punch down
location.
ote: The connection is polarity sensitive.
tep Action
Basic et-Up
Page 4 TYPE 6.5.0.7-RF
Door Ring Patterns
Door 1 3 groups of 3 rings (ring ring ring), (ring ring ring), (ring ring ring).
Door 2 3 groups of 2 rings (ring ring), (ring ring), (ring ring).
Operation of TE 2
AN WER THE CALL
When you heat the distinctive ring pattern selected above:
within 10 seconds - simply pick up any telephone to be connected to the door speaker which initiated the call.
after 10 seconds - pick up any telephone, flash, and you will be connected to door 1. To be connected to door 2, pick up
telephone, flash, and hit “2
CALL WAITING
TES2 has built-in call waiting. If the house phone is in use when the door button is pushed, the caller will receive a call
waiting tone. To answer the “door call” simply flash to answer the “door call” and flash again to return to the original call.
WITCH TO OTHER DOOR
Users can switch to the other door station at anytime by hitting “1” or “2” while connected to door 1 or door 2.
Operation of T-RLY
If the TES2 Relay board is installed, the door latch/gate relay can be activated by pushing “6”. The relay will be activated for 5 sec-
onds,. To increase the activation time, hold down the “6” key for the desired amount of time.
C1 C O1 C2 C O2
Door 1 Door 2
Optional T-Rly Board (9408-3)
Page 5 TYPE 6.5.0.7-RF
TE 2 Telephone Entry ystem
501 E. Goetz Ave.
anta Ana, Ca 92707
Ph. 714-434-6904
Fax 800-362-0002
www.eholovision.com
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere HOLOVISION Gegensprechanlage Handbücher
HOLOVISION
HOLOVISION 400-A-VoIP Bedienungsanleitung
HOLOVISION
HOLOVISION 420-VIO2 Bedienungsanleitung
HOLOVISION
HOLOVISION 400-W-VIK Bedienungsanleitung
HOLOVISION
HOLOVISION 400-A-PAN Bedienungsanleitung
HOLOVISION
HOLOVISION 400-A-VIO Bedienungsanleitung
HOLOVISION
HOLOVISION 404-W-VoIP Bedienungsanleitung
HOLOVISION
HOLOVISION 101-VIK Bedienungsanleitung
HOLOVISION
HOLOVISION Viking E-40 Bedienungsanleitung
HOLOVISION
HOLOVISION 400-S12-TES2 Bedienungsanleitung
HOLOVISION
HOLOVISION 400-S12-VIO2 Bedienungsanleitung
HOLOVISION
HOLOVISION 400-S12-PAN Bedienungsanleitung
HOLOVISION
HOLOVISION 400-A-VIK Bedienungsanleitung
HOLOVISION
HOLOVISION Viking E-10 Bedienungsanleitung
HOLOVISION
HOLOVISION 401-W-PAN Bedienungsanleitung
HOLOVISION
HOLOVISION 400-S12-VIK Bedienungsanleitung
HOLOVISION
HOLOVISION 401-A-PAN2 Bedienungsanleitung
HOLOVISION
HOLOVISION 100-Pan2 Bedienungsanleitung
HOLOVISION
HOLOVISION 400-W-TES2 Bedienungsanleitung
HOLOVISION
HOLOVISION 401-W-VIO Bedienungsanleitung
HOLOVISION
HOLOVISION 400-S12-PAN2 Bedienungsanleitung
