Holzhof SULTAN Bedienungsanleitung

assembly instructions

SULTAN / OXI range

XS11 / XOXI11 "Casablanca"

ver.01 - 10.2014

Le misure sono espresse in cm.

firma esecutore :

data : 10.2014

denominazione

e/o cliente :

istruzioni di montaggio

XS11 / XOXI11

nr.

Colori e modelli rappresentati

sono puramente indicativi

pagina 2

PLEASE NOTE: It is advisable to only secure the

nuts and bolts permanently and insert the caps

once it has been checked that all the elements

have been positioned correctly.

Fasten the slide to the tower uprights, inserting

4 TEL M8x80 screws (two per side) for wooden

towers or 4 TEFR 6.3x80 screws for aluminum

towers into the holes at the beginning of the

slide.

Le misure sono espresse in cm.

firma esecutore :

data : 10.2014

denominazione

e/o cliente :

istruzioni di montaggio

XS11 / XOXI11

nr.

Colori e modelli rappresentati

sono puramente indicativi

pagina 3

PLEASE NOTE: It is advisable to only secure the

nuts and bolts permanently and insert the

caps once it has been checked that all the

elements have been positioned correctly.

Secure the climbing board to the tower

inserting from the inside of the tower 2x

TEL M8x130 for wooden towers or 2x

TEFR M6.3x120 for aluminium towers

(including nut covers and caps so that the

nuts and bolts are not exposed).

Article

no. Quantity CODE NO. NAME

IS07089 washer diam. 8

59x59x35 stainless steel angle bar

PE nut cover

PE cap

1. Position the upright and the angle bar on the support surface

and mark the position of the plug.

2. Drill the support surface and position the plug.

3. Secure the angle bar to the support surface and (if not done

previously) to the upright using the appropriate nuts and bolts,

as indicated in the figure.

TEFR 6.3x50 screw

washer diam.10

M10 self-locking nut

M10 self-locking plug

1. Drill a hole.

2. Thoroughly clean the hole using an air

pump and brushes.

3. Insert the anchor in the hole present

on the angle bar.

4. Tighten using a torque wrench.

PLEASE NOTE: It is advisable to only secure the nuts

and bolts permanently and insert the caps once it

has been checked that all the elements have been

positioned correctly.

1. Position the climbing board on the support surface,

marking the position of the plugs.

2. Drill the support surface and position the plugs.

3. Secure the angle bars to the support surface using

appropriate nuts and bolts, as shown in the figure.

Article

no. Quantity CODE NO. NAME

PE nut cover

PE cap

PE climbing board

59x59x35 stainless steel angle bar

M10 self-locking nut

Washer diam.10

M8x115 plug

NOTE: the combination of colours and

models shown is for illustration purposes

only.

The climbing board can measure

84-144-192 cm in height.

Article

no. Quantity CODE NO. NAME

59x59x35 stainless steel angle bar

PE nut cover

PE cap

M10 self-locking nut

M8x115 plug

Washer diam.10

1. Position the slide on the support surface, marking the

position of the plug.

2. Drill the support surface and position the plug.

3. Secure the angle bar to the support surface using the

appropriate nuts and bolts, as indicated in the figure.

NOTE: the combination of colours and models shown is for

illustration purposes only.

The slide can measure 84-144-192 cm in height.

1. Hook the (1) brackets, inserting in sequence:

(2) Pe nut cover, (3) M8 washer, (4) M8x25 hex

screw, (5) Pe cap

1. Make two holes that are 30 cm in diameter and 60 cm deep.

PLEASE NOTE: It is advisable to only secure the

nuts and bolts permanently and insert the caps

once it has been checked that all the elements

have been positioned correctly.

2. Cast a first layer of concrete that is 10 cm thick.

3. Once the concrete has hardened, position the climbing board

brackets in the hole, checking correct alignment of the bottom of the slide

with the level of the finished terrain.

4. Finish casting the concrete as shown in the diagram.

5. Once the concrete has hardened, fill the hole, tamping it with the

left over material until reaching the height of the finished terrain.

1.Make a hole that is 30 cm in diameter and 60 cm deep.

2. Cast a first layer of concrete that is 10 cm thick.

3. Once the concrete has hardened, position the slide brackets

in the hole, checking correct alignment of the bottom

of the slide with the level of the finished terrain.

Dieses Handbuch passt für folgende Modelle

Andere Holzhof Spielgeräte und Spielplatzausstattung Handbücher

Holzhof

Holzhof MAX XM 100 LP PUR Bedienungsanleitung

Holzhof

Holzhof LINEA ALADIN XA 100 RAP Bedienungsanleitung

Holzhof

Holzhof ALADIN Bedienungsanleitung

Holzhof

Holzhof SULTAN XS 312 Bedienungsanleitung

Holzhof

Holzhof LINEA ALADIN XA 100 RP Bedienungsanleitung

Holzhof

Holzhof MAX XM 100 RAP Bedienungsanleitung

Holzhof

Holzhof MAX XM 209 P Bedienungsanleitung

Holzhof

Holzhof OASIS XOA 100 Bedienungsanleitung

Holzhof

Holzhof MAX XM 208 LP PUR Bedienungsanleitung

Holzhof

Holzhof MAX XM 100 RP line Bedienungsanleitung

Holzhof

Holzhof XT 100 Dirondello Bedienungsanleitung

Holzhof

Holzhof MAX XM 100 R line Bedienungsanleitung

Holzhof

Holzhof MAX XM 202 RA Bedienungsanleitung

Beliebte Spielgeräte und Spielplatzausstattung Handbücher anderer Marken

Ledon

Ledon 302040 Bedienungsanleitung

FUNormous

FUNormous Disney Junior MICKEY MOUSE Bedienungsanleitung

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Bedienungsanleitung

PoolMaster

PoolMaster 72775 Bedienungsanleitung

Palmako

Palmako 4743142009857 Installationshandbuch

BOERPLAY

BOERPLAY PSTE000.019 Bedienungsanleitung

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Benutzerhandbuch

stilum

stilum Erika Bedienungsanleitung

Costway

Costway NP10816 Bedienungsanleitung

Trigano

Trigano VABI Bedienungsanleitung

Outward

Outward OUT116 Bedienungsanleitung

GALOPIN

GALOPIN ARC02 Bedienungsanleitung

stilum

stilum levis Technische Daten

Ledon

Ledon BASIC Bai LB012 Bedienungsanleitung

BOERPLAY

BOERPLAY PSTE115.002 Bedienungsanleitung

Europlay

Europlay S306 Programmierhandbuch

SportsPlay Equipment

SportsPlay Equipment 361-509H Bedienungsanleitung

Ledon

Ledon 302250 Bedienungsanleitung