HoMedics EnviraScape WFL-SLFA Leitfaden

Instruction Manual and

Warranty Information WFL-SLFA

ILLUMINATED TABLETOP RELAXATION FOUNTAIN

SLATE

FALLS

HoMedics, Inc. and its affiliated companies. Envirascape™ is a trademark of HoMedics, Inc. and its affiliated

IB-WFLSLFA

ONE YEAR LIMITED WARRANTY

(Valid in USA only)

HoMedics, Inc., guarantees this product free from defects in material and

workmanship for a period of one year from the date of purchase, except

as noted below.

This HoMedics product warranty does not cover damage caused by mis-

use or abuse; accident; the attachment of any unauthorized accessory;

alteration to the product; or any other conditions whatsoever that are

beyond the control of HoMedics. This warranty is effective only if the

product is purchased and operated in the USA. A product that requires

modification or adaptation to enable it to operate in any country other

than the country for which it was designed, manufactured, approved

and/or authorized, or repair of products damaged by these modifications

is not covered under warranty. HoMedics shall not be responsible for any

type of incidental, consequential or special damages. All implied war-

ranties, including but not limited to those implied warranties of fitness

and merchantability, are limited in the total duration of one year from

the original purchase date.

To obtain warranty service on your HoMedics product, either hand deliver

or mail the unit and your dated sales receipt (as proof of purchase), post-

paid, along with check or money order in the amount of $5.00 payable to

HoMedics, Inc. to cover handling.

Upon receipt, HoMedics will repair or replace, as appropriate, your prod-

uct and return it to you, postpaid. If it is appropriate to replace your

product, HoMedics will replace the product with the same product or a

comparable product at HoMedics’ option. Warranty is solely through

HoMedics Service Center. Service of this product by anyone other than

HoMedics Service Center voids warranty.

This warranty provides you with specific legal rights. You may have addi-

tional rights which may vary from state to state. Because of individual

state regulations, some of the above limitations and exclusions may not

apply to you.

FFoorrmmoorreeiinnffoorrmmaattiioonnrreeggaarrddiinnggoouurrpprroodduuccttlliinneeiinntthheeUUSSAA,,pplleeaasseevviissiitt::wwwwww..hhoommeeddiiccss..ccoomm

Mail To:

HoMedics

Consumer Relations

Service Center Dept. 168

3000 Pontiac Trail

Commerce Township, MI

48390

e-mail:

[email protected]om

phone:

800-466-3342

WFL-SLFA_6.qxd 8/26/05 11:16 AM Page 1

The soothing sounds of nature

Thank you for purchasing EnviraScape, HoMedics’ tabletop

relaxation fountain. This, like the entire HoMedics product line,

is built with high-quality craftsmanship to provide you years of

dependable service. We hope that you will find it to be the

finest product of its kind.

EnviraScape enables you to create an all-encompassing envi-

ronment with sound. The sound of flowing water enhances

your environment by releasing negative ions, and promoting

relaxation. Only EnviraScape offers you the luxury of these vital

benefits with its creative design which adds beauty to any

indoor environment.

EnviraScape Features

• Innovative, artistic design enhances the environment at

home or at work.

• Special effect lighting illuminates fountain for a more

dramatic effect.

• The soothing sound of cascading waters create a stress

free ambiance.

• Improves concentration by masking distractions so you can

stay focused.

• Durable electrical water pump can be operated from any

indoor electrical outlet.

• Convenient tabletop size-fountain measures

7.5"L x 7.5"W x 14"H.

IMPORTANT SAFETY INSTRUCTIONS:

When using an electrical appliance, basic precautions should

always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

DANGER

- To reduce the risk of electric shock:

• Always unplug the appliance from the electrical outlet

immediately after using and before cleaning.

• Do not reach for an appliance that has fallen into water.

Unplug it immediately.

•

Do not place or store appliance where it can fall or be pulled into

a tub or sink. Do not place in or drop into water or other liquid.

•

Do not connect to any voltage other than that shown on the pump.

• Do not pump flammable liquids.

• Do not use water above 86oFahrenheit .

WARNING - To reduce the risk of burns, fire, electric shock or

injury to persons:

• An appliance should never be left unattended when plugged in.

Unplug from outlet when not in use and before putting on or taking

off parts or attachments.

• Close supervision is necessary when this appliance is used by or

near children, invalids or disabled persons.

• Use this appliance only for its intended use as described in this

manual. Do not use attachments not recommended by HoMedics;

specifically any attachments not provided with the unit.

• Never operate this appliance if it has a damaged cord, plug, pump,

cable or housing. If it is not working properly, if it has been

dropped or damaged, return it to Homedics Service Center for

examination and repair.

• Keep cord away from heated surfaces.

• Never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used

or where oxygen is being administered.

• Do not carry this appliance by power cord or use cord as handle.

• To disconnect, remove plug from outlet.

• This appliance is designed for indoor use only.

Do not use outdoors.

SAVE THESE INSTRUCTIONS

Caution – Please read all instructions

carefully before operating.

• Never leave the appliance unattended, especially if children

are present.

• Never cover the appliance when it is in operation.

• This unit should not be used by children without

adult supervision.

• Connect the pump with the proper voltage as indicated

on the pump label.

• Always keep the cord away from high temperature and fire.

• Unplug the pump from power source before cleaning,

maintenance or disassembling.

• To get the best flowing effect, product must be placed on a flat

surface and should never be placed on an electrical appliance.

• Never let pump run dry, as this will shorten life of the pump.

• Do not lift, carry, hang, or pull the pump by the power cord.

• Operate with tap or distilled water.

• Operate pump completely submerged for proper cooling.

• The electrical cord of this product cannot be replaced. If it sustains

damage, you must stop using this product immediately and return

it to the HoMedics Service Center for repair. (See the warranty

section for HoMedics address.)

• Disconnect the appliance from outlet before putting hands into water.

CAUTION:

The pump must

be completely

submerged in

water. If the

pump is

making noises,

most likely it is

not completely

submerged in

water.

CAUTION:

Only set the

fountain and

fountain parts

on waterproof

surfaces

WFL-SLFA_6.qxd 8/26/05 11:16 AM Page 3

SCREW

SHORTSHORT

SCREW

SMALL END OF

COPPER TUBE

CENTER HOLE

LIGHT HOLE

Minimum Water Level

Flow Control Valve

(+) faster water

output

(-) slower water

output

Attention:

In order to get

best results,

please operate

pump completely

submerged.

Keep the water

level above the

minimum water

level ALL THE

TIME.

Figure 2

3. Insert the small end of the copper tube through the center hole of the plat-

form and secure with the short screws and corresponding nuts. (Fig. 3)

4. Insert the waterproof light into the light hole located under the platform. (Fig.

4) Be sure to push far enough so “rubber neck” is secure in the light hole.

Slight twisting may help to push the rubber neck through the hole more -

easily. Note: Be gentle with the bulb cover since it is made of glass.

Assembly and Instructions for Use

1. Unpack the product. Wipe off dust with a damp cloth. (Fig 1)

2. Familiarize yourself with the pump. The pump speed is controlled by

the switch located at the front of the pump. The speed is indicated by

a plus (+) and minus (-) sign. To increase the speed, move the switch

slowly downward in the direction of the plus sign. You will hear a click

as the switch moves to each speed level. At its highest speed level,

the switch will cease to move any further. To decrease the pump

speed, move the switch upward toward the minus sign. Similarly, at its

lowest speed, the switch will cease to move any further (Fig 2).

NOTE: It is recommended the pump be set at its highest speed dur-

ing assembly and later adjusted to a lower setting if desired. Be sure

to unplug the pump before adjusting the speed setting.

4 5

NUT

SCREW

U-SHAPED

CLIPS

SCREW

SHORTSHORT

LONG LONG

SWITCHSWITCH

BASE

PUMP

AC ADAPTOR

SCREW

SLATE WALL

PLASTIC TUBE

CONNECTOR

WATER

PLATFORM

SMALL END OF

COPPER TUBE

CENTER HOLE

LIGHT HOLE

WATERPROOF LIGHT

Figure 1

Figure 3

WATERPROOF

LIGHT

LIGHT HOLE

PLATFORM

Figure 4

WFL-SLFA_6.qxd 8/26/05 11:16 AM Page 5

9. Hold the slate wall in between the U-shaped clips, aligning the holes.

Then, slide the long screws through the holes. Secure with the corre-

sponding nuts on the back. (Fig. 9)

10. Fill the base with clean water until the water level is 3/4” below the

lowest edge of the base. (Fig. 10)

11. Attach the A/C adaptor jack to the base power cord. (Fig. 1)

5. Insert the small end of the copper tube into the plastic tube

(the end without the black connector). (Fig. 5)

6. Insert the end of the plastic tube with the black connector into the pump.

(Fig. 6)

7. Then place the platform on the base so it sits level. Lead the cord out

through the cord slot located on the upper backside of the base. (Fig 7.)

8. Slide the U-shaped clips over the copper bar, one on either side of the

vertical pole. (Fig. 8)

6 7

BLACK

CONNECTOR

PLATFORM

PLASTIC

TUBE

SMALL END OF

COPPER TUBE

BLACK

CONNECTOR

PLASTIC

TUBE

SMALL END OF

COPPER TUBE

BASE

PUMP

PLATFORM

CORD

SLOT

COPPER TUBE

PLATFORM

U-SHAPED

CLIPS

SLATE WALL

VERTICAL POLE

NUT

U-SHAPED

CLIPS

SCREWS

LONG

SLATE WALL

Figure 5

Figure 6

Figure 7 Figure 8

Figure 9

Figure 10

12. Plug the cord into 120V household outlet. The fountain is controlled by

a switch located on the power cord. If pump does not operate, rotate

in-line switch once to turn “on” and once to turn “off”.

Note: Ensure that the electrical cord loops below the electrical outlet to

form a “Drip Loop”. This will prevent water from running down the

electrical cord into the electrical outlet. (Fig. 11)

WFL-SLFA_6.qxd 8/26/05 11:16 AM Page 7

Troubleshooting

• If the pump fails to operate, check the following:

Check the circuit breaker, or try a different outlet to make sure the

pump is getting electrical power.

NOTE: Always disconnect from electrical outlet before handling the pump.

• If the pump gurgles, spews, or “burps”:

Check the water level to make sure the pump has enough water

to function.

•Obtaining a desired water level:

Check the water level daily the first week to mea sure the rate of

evaporation; refill with water as needed.

•If water is splashing outside the fountain:

Adjust the flow control valve to a lower setting on the pump.

Maintenance

• To clean the pump:

Unplug from electrical outlet. Remove it from the base of the

fountain. Use a small brush or stream of water to remove any

debris (Fig 12).

• To keep water clean:

Periodically change water and clean the product according to the water

condition. Keeping the water clean prevents the water from becoming

sticky and forming micro-organisms. We recommend distilled water to

prevent mineral build-up.

• To clean off hard water deposits on the base:

Soak the container in a mixture of vinegar and water to clean and remove

any mineral build-up.

• Keeping the water at an optimum level:

Add water periodically to keep water level at an optimum level to avoid

shortening the life of the pump.

NOTE: Never let the pump run dry, as this will shorten the life of the pump.

• Fountain storage

Unplug the fountain from the electrical outlet, empty the water, and store

rocks and fountain in a dry, cool place.

• Changing the light bulb

First unplug fountain and let bulb cool down. Remove the bulb cover by

holding glass bulb cover in dry hand and rubber neck with other hand. Slowly

pull apart. Slight twisting may help to loosen. Be gentle with bulb cover since

it is glass. Never pull on cord. Next pull bulb straight out and replace with new

bulb, inserting prongs into the holes. Replace bulb cover securely.

Caution:

All servicing

of this fountain

must be

performed

by authorized

HoMedics

service

personnel only.

Drip Loop

Figure 11

Figure 12

Front Plate

PVC Tubing

Inserts Here Back Plate

Suction Feet

Impeller

Pump Inlet

Flow

Control

Lever

Housing

WFL-SLFA_6.qxd 8/26/05 11:16 AM Page 9

PP-ROCKBLB Replacement bulbs and covers for $5.00

WFL-SLFA - pack of 5

SUBTOTAL

TAX-Michigan Residents add 6%

Total

Name

Address

City State Zip Code Phone Number

( )

Detach and return order form with check or money order payable to HoMedics, Inc.

Please allow 2 to 4 weeks for delivery.

Replacement Parts Order Form

PART DESCRIPTION QUANTITY COST

Mail To:

HoMedics

Consumer Relations

Service Center Dept. 168

3000 Pontiac Trail

Commerce Township, MI

48390

e-mail:

[email protected]om

ILLUMINATED TABLETOP RELAXATION FOUNTAIN

WFL-SLFA_6.qxd 8/26/05 11:16 AM Page 11

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HoMedics Freiluftbrunnen Handbücher

HoMedics

HoMedics Mirra PURITY WFL-220 Bedienungsanleitung

HoMedics

HoMedics enviraScape MINI MOON RIVER WF-MN-MOON Bedienungsanleitung

HoMedics

HoMedics EnviraScape WFL-GDN Leitfaden

HoMedics

HoMedics enviraScape Gentle Rains WRF-GEN Bedienungsanleitung

HoMedics

HoMedics AQUASCAPE AQ-DANC Bedienungsanleitung

HoMedics

HoMedics enviraScape MODERN GLOW PILLAR WFL-CAN33 Bedienungsanleitung

HoMedics

HoMedics ENVIRASCAPE WRF-REL Bedienungsanleitung

HoMedics

HoMedics enviraScape SERENITY WFL-SERE Bedienungsanleitung

HoMedics

HoMedics Mirra ZEN WFL-200 Bedienungsanleitung

HoMedics

HoMedics enviraScape OLD NAPOLI Bedienungsanleitung

HoMedics

HoMedics enviraScape SERENITY FOUNTAIN Bedienungsanleitung

HoMedics

HoMedics enviraScape LANTERN MIST WF-LAMI Bedienungsanleitung

HoMedics

HoMedics enviraScape ITALIAN GARDENS WFL-ITL Bedienungsanleitung

HoMedics

HoMedics enviraScape SIENA WFL-SIEN Bedienungsanleitung

HoMedics

HoMedics EnviraScape Slate Streams WFL-SLST Bedienungsanleitung

HoMedics

HoMedics EnviraScape WFL-SLMP and warranty Leitfaden

HoMedics

HoMedics enviraScape ARTESIAN GLOBE WFL-ART Bedienungsanleitung

HoMedics

HoMedics Mirra TIDE Bedienungsanleitung

HoMedics

HoMedics Envirascape Rock Garden Bedienungsanleitung

HoMedics

HoMedics Mirra CASCADE WFL-510 Bedienungsanleitung

HoMedics

HoMedics enviraScape ASPEN FALLS WFL-ASP Bedienungsanleitung

HoMedics

HoMedics enviraScape GLISTENING STEPS WFL-GLS Bedienungsanleitung

HoMedics

HoMedics EnviraScape WRF-SOO Bedienungsanleitung

HoMedics

HoMedics EnviraScape WF-ZEN Leitfaden

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

Elkay

Elkay FLEXI-GUARD EFHA8 1M Series Installationshandbuch

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung