Homeguard HGWVD-730 Bedienungsanleitung
Doorcam User Manual
www.vstarcam.com
Function and Features
◎Visitor records, visitor snapshot and other information are stored in the cloud, user
can check at anytime, anywhere;
◎Press doorcam, will automatically snapshot and push to the smartphone APP;
◎CMOS image sensor;
◎Easy to install, can use 3M adhesive paste installation or screw fixation;
◎Ultra-low power consumption, 2pcs AAA batteries can last for one year;
◎Never offline, WiFi + RF wireless transmission, always keep online;
◎Anti-theft alarm function, when the outdoor unit leave the wall, the indoor unit will
be issued an alarm;
◎Clear night vision, even at no light condition can automatic fill light
Product Diagram
I. Indoor Unit
Funciton key Quickly press it three times, it will enter code pairing
mode
Long pressing for 5 seconds, WiFi settigns will be
reset
Key lightFlash quickly:Switch ringtone/talking to outdoor unit
Flash slowly:Network connection failure
Network lightIndicate the network status, more details, please see the chart below.
Volume key + Raise the volume/switch to the last ringtone
Volume key - Lower the volume/switch to the next ringtone
Speaker Issue ringtone
Meaning of indoor indicator light：
Network indicator
light（red）
Key light（blue）
Meaning
Flash once per sec
off
Waiting for WiFi configuration
Stable on
off
WiFi configuration success
Stable on
Flash once per sec
WiFiconfiguration failure
Flash quickly
off
Code pairing
Stable on
Flash slowly
Switch ringtone and volume
Stable on
Flash
quickly→Flashslowly
Pressed doorbell
II. Specification
Outdoor device
Picture resolution: 480X320
Night Vision: One white light
Power supply mode: DC 3V (two 1.5v AAA batteries)
Transmission: RF+WiFi
Installation: 3M glue or screw fixed
Image sensor: 1/4 CMOS sensor
Lens: 98.5°, F2.4 aperture
Alarm: buzzer
Size: 121*67*16.5
Indoor device
WiFi：WiFi2.4G
Transmission distance: RF 30 meters + WiFi 30 meters
Rated input voltage: Wide voltage 100V-240VAC
Alarm: buzzer
Shell material: flame retardant abs plastic.
Plug : US and EU
Size: 99*46*50
III. Product introduction
Outdoor Unit
CoverCover
LensTake snapshot of visitors
LED lightWhen the light is not enough, auto fill the light,optimize the capture effect.
Doorbell ButtonVisitors press the button and the indoor unit rings and take snaps of
visitors.
IV. Connect the Doorbell
Please follow these steps to install the doorbell:
Step 1:Open the box and take out the indoor unit, outdoor unit and accessories.
Step 2: Install the battery for the outdoor unit.
Remove the outdoor unit from the rain-proof cover, take away the back cover along
the gap, confirm the positive and negative electrode of the battery according to the
diagram, laid down a pair of batteries correctly, and then put the back cover back in.
When the doorbell is properly energized, the key light flashes three times.
Note: If the battery is wrongly placed, the electronic components of the doorbell
may be burnt.
Step 3: Plug in the indoor
unit (socket or plug).
After powered on, the indoor unit makes two dingdong sound, the key light will be on
and go out after 2 seconds.
Note: Please plug in the indoor unit in the socket 5 meters away from the router.
英6
Step 4: Take the outdoor unit together with the indoor unit(within two meters), make
sure they are commnucating with each other. After finish all the settings, we can
install it to the door or wall.
Note: The indoor and outdoor units have been paired when out of factory, which
can be confirmed by the following methods: Short press the outdoor unit, if the
indoor unit rings and the white light on the outdoor flash once, that means the
indoor and outdoor units have been successfully paired.
If the indoor unit does not ring and the outdoor unit make beep sound, that
means they are not paired, and the code matching should be re-conducted
according to the method in the "Code Pairing" section below.
Step 5: If the indoor and outdoor units are successful paired, and all the indicator
lights funciton normally, please jump to the "Add the doorbell to mobile phone
APP" section and start to configure WiFi for the doorbell.
V. Reset and Code matching
1. Reset(Re-configure the WiFi network)
Power on the indoor unit, long pressing the function key for 3~5 seconds, it will make
doorbell sound. After release the funciton key, the red indicator will flash once per
second, which means it has been reset successfully.
Note: If the indicator does not flash once per second, please reset it again by
referring to the guide above.
2. Code Pairing（To pair the indoor and outdoor units）
Note: Please follow the steps below, to press the indoor unit first and then press
the outdoor unit. Don't press them at the same time.
Step 1:
Indoor unit
To press the function key of the indoor unit three times quickly, it will make doorbell
sound and the red network indicator will flash quickly, then it will enter waiting code
matching status. 英10
Step 2:
Outdoor unit
Keep holding the doorbell button on the outdoor unit for 3 seconds to send the code
to the indoor unit, then the code matching will be completed. If the code matching is
successful, when pressing the doorbell button on the outdoor unit, the indoor unit will
make doorbell sound，the red network light will become steady on.
VI. Connection Topology
VII. Add the doorbell to the APP
1、Software download
① Go to Google Play or Apple Store to search „Eye4‟ and to download.
②Visit [http://www.eye4.so] for software download and install.
③Scan QR code to download.
2、Register account
For android / iOS client APP, please select “Register now”, click to enter the
registration page, enter user name, password, then confirm to complete the
registration.
英14
3、Add device
Add indoor unit to theAPPfor mobile phone
Please refer to the steps ①②③ below in sequence.
① Login the APP, click on “+”on the top right corner. There are two ways to add the
doorbell:
A. To scan QR code. Tap the„To scan QR code‟and scan the QR code on the label of
the indoor unit, then follow the prompt on the APP, go to step ②.
图15-1 图15-2
B. If it failed to add by scanning QR code, then please refer to the„Others→Take the
camera door to add→D2 smart doorbell', then follow the prompt on the APP, go to
step ②.
Attention: If the indicator does not flash at once per second, please reset the indoor
unit.
【Reset method: Please refer to the reset method in chapter VIII】
②The step ②for different phones are as follows:
Android devices
To add the doorbell for the first time, please select the WiFi that the phone connected
and input the WiFi password, then go to next.
IOS devices
To add the doorbell for the first time, please follow the guide on the page, manually
connect to the doorbell‟s hotspot DoorBell.XXXXXX, input the password of the
hotspot: 12345678, then return to the APP, select the home WiFi,input the WiFi
password and click to go to next step.
图18-1 和图 18-2
The APP will find the smart doorcam nearby, customize the name and click Add to
bind the doorbell. Then it will enter the automatic network configuration status(this
process will lasts about 20 seconds), after successfully bound, the doorcam will be
shown in the APP.
Note：1. After the indoor unit being successfully bound to the APP, the red
network indicator on the indoor unit will be steady on. If the indicator display
abnormally or the device does not work properly, please check the connection
and try to reset the device and re-add it.
2. The indoor and outdoor units have been paired when out of factory, in case of
unexpected factors lead to disconnection between them, please follow the steps of
code matching in chapter VIII to re-match them.
XI、Use and share
①When visitor comes to press the doorcam, the outdoor unit will take a snapshot ,
and push the picture to the smartphone ; the indoor unit will also issue doorbell tone.
图21
APP, click the on the
②On the home page of the
right corner of the doorbell, go to settings of the doorbell.
We can re-name the doorbell, share it to other
smartphones, choose other ringtone, adjust the volume
firmware.图22of the doorbell and upgrade
Inhaltsverzeichnis
