Honeywell Home THM5421R1021 Bedienungsanleitung

Equipment Interface Module works with:

• Prestige IAQ

• VisionPRO 8000 with RedLINK®

• Wireless FocusPRO with RedLINK (not pictured below)

Equipment

Interface Module

THM5421R1021

Installation Guide

Read before installing

M39123

Equipment Interface Module

M39126

Prestige/VisionPRO with RedLINK: Mount the thermostat and wire to C and

R terminals of the Equipment Interface Module (EIM), or to a separate 24 volt

transformer (not provided).

NOTE: When the VisionPRO with RedLINK thermostat is used with the EIM,

the relays in the thermostat do not function.

M38709

Strip 1/4”

insulation,

then insert

wires as

shown.

Use screws

& anchors as

appropriate for

the mounting

surface. Mount

the EIM near the

HVAC equipment,

or on the

equipment itself.

M34048A

NOTE: If you install more than one

thermostat and EIM, the EIMs must be at

least 2 feet apart.

NOTE: If you are installing discharge and

return air sensors, refer to the mounting

instructions in the Alerts and Delta T

Diagnostics Installation Instructions packed

with the Prestige IAQ kit.

NOTE: RedLINK FocusPRO should use a

return sensor to S1 only. Do not wire a supply sensor.

If an EIM is mounted inside a metal cabinet, it is recommended to use a

THM4000R1000 Wireless Adapter for extended wireless range. Mount the

Wireless Adapter outside the metal cabinet and connect to the ABCD terminals

at the EIM.

O/B

AUX

-E

L/A

CONVENTIONAL

HEAT PUMP

M39127

Install thermostat

Install equipment interface module

EIM

M39124

WIRELESS

ADAPTER

CONNECT

POWER

THM1234

CONNECTED

WIRELESS SETUP

NOTE: RedLINK FocusPRO are battery powered and do not have R and C

terminals.

Power optional RedLINK accessories

3.1 Install batteries in RedLINK accessories.

• Portable Comfort Control

• Wireless Outdoor Sensor

• Wireless Indoor Sensor (Prestige & RedLINK VisionPRO

only)

• Wireless Entry/Exit Remote

• Wireless Vent and Filter Boost Remote

3.2 Connect gateway to internet and

connect to power.

3.2a Connect RedLINK Internet

Gateway to router or modem

with Ethernet cable (RJ45).

3.2b Connect gateway’s power cord to an electrical outlet that

is not controlled by a wall switch.

M36568A

INTERNET

POWER

REDLINK

Performing initial setup

Initial setup options deﬁne the type of system you are installing: *

• Residential or commercial (Prestige & RedLINK VisionPRO only)

• Non-zoned or zoned

4.1 Follow prompts on the screen to select appropriate options.

4.2 Link the thermostat to the

equipment interface module.

4.2a Press and quickly release the

CONNECT button on the EIM.

Make sure the “Connected” light

is flashing green.

* RedLINK FocusPRO shows numbers on

the display during setup. Follow install guide

included with that thermostat.

M34176A

CONNECT

CONNECTED

APPLICATION

residential

NOTE: If the “Connected” light does NOT flash green, another system may be

in the listening mode. Please exit the listening mode at the other system and

then try again.

• Green Flashing: In Listening Mode - system is ready to add RedLINK

devices.

• Green Steady: RedLINK devices are communicating.

• Red: RedLINK device(s) are NOT communicating. Check EIM and

RedLINK devices.

4.2b While the “Connected” light is flashing green on the EIM, press

NEXT on the thermostat. After a short delay, the screen will show the

thermostat is connected.

4.3 When you see the prompt Do you have RedLINK accessories to

connect? Touch YES or NO. *

• If you select YES, you will be prompted to Press Connect on all new

accessories. Continue to Step 4.4.

• If you select NO, continue to Step 4.5.

4.4 Connect each RedLINK accessory.

NOTE: Make sure accessories are at least 2 feet away from the EIM during

the linking process.

4.4a While the Add Device screen is displayed (listening mode), press

and quickly release the CONNECT button on each new RedLINK

accessory.

NOTE: The Prestige or RedLINK VisionPRO display will instruct you to press

connect on the accessory while in listening mode.

* RedLINK FocusPRO display will say “wireless setup” in display when it is ready to

connect to the EIM and accessories during the initial setup.

M34248

4.4b After a short delay (up to 20 seconds), check the thermostat to

confirm the connection of each RedLINK accessory.

4.4c Touch DONE at the thermostat after all new RedLINK accessories are

connected.

NOTE: The thermostat stays in listening mode for 15 minutes from when it

was connected to the EIM or RedLINK Zone Panel. The timer is reset every

time a new accessory was added. When done adding RedLINK accessories

press DONE on the thermostat display.

Done

4.5 Finish the initial setup.

Finish the setup by selecting the desired options. Touch DONE after you

select the last option you want to change.

For RedLINK FocusPRO, these settings are in numbers rather than text,

so you will need to use the Installation instructions included with the

thermostat.

The thermostat now displays its Home screen and the thermostat setup is

complete.

RedLINK FocusPRO Home screen not shown in this ﬁle.

Typical wiring of a conventional system with up to 3-stage heat and 2-stage cool

with one transformer. (RedLINK FocusPRO up to two-stage heat and two-stage

cool.)

NOTE: See following pages for additional thermostat wiring guidelines for

heat pumps, geothermal systems and optional Economizer.

See guides on following pages for thermostat wiring and geothermal radiant

heat wiring.

Wire a maximum of 4 sensors using the S1S4 terminals. S1S4 terminals can

be connected to an indoor sensor, outdoor sensor, discharge sensor, return

sensor, dry contact device to display an alert or an occupancy sensor for

remote setback. RedLINK FocusPRO should only use the return sensor to any

of the four sets of S terminals.

Remove jumper(s) if using separate transformers.

See Economizer wiring section.

HEAT STAGE 1

HEAT STAGE 2

HEAT STAGE 3

FAN

TO THERMOSTAT

STATUS

LEDS

JUMPERS

SENSORS

CONV

FURNACE

TRANSFORMER

120

VAC

COMPRESSOR

STAGE 1

COMPRESSOR

STAGE 2

POWER

HEAT

COOL

FAN

U3 A

CONNECT OPTIONAL

SENSORS TO

S1 AND S2 TERMINALS

CONNECT OPTIONAL

SENSORS TO

S3 AND S4 TERMINALS

EIM

M34249

EIM wiring guide — conventional systems

Connect wireless adapter to ABCD for extended wireless range.

EIM wiring guide — heat pump systems

Typical wiring of a heat pump system with up to four-stage heat and two-stage

cool with one transformer. (RedLINK FocusPRO up to three-stage heat and two-

stage cool.)

See guides on following pages for thermostat wiring and geothermal radiant

heat wiring.

Wire a maximum of 4 sensors using the S1S4 terminals. S1S4 terminals

can be connected to an indoor sensor, outdoor sensor, discharge sensor,

return sensor, dry contact device to display an alert or an occupancy sensor

for remote setback. RedLINK FocusPRO should only use the return sensor to

any of the four sets of S terminals.

L/A terminal sends continuous output when thermostat is set to EM HEAT

mode, except when set up for Economizer or TOD. See Economizer wiring

section. (Only Prestige and RedLINK VisionPRO can be set for Economizer or

TOD.)

CHANGEOVER VALVE

BACKUP HEAT

STAGE 1

FAN RELAY

SENSORS

TO THERMOSTAT

HEAT PUMP

AIR HANDLER

TRANSFORMER

120

VAC

COMPRESSOR

STAGE 1

COMPRESSOR

STAGE 2

O/B

AUX1

AUX2

O/B

BACKUP HEAT

STAGE 2

COMPRESSOR

MONITOR OR

ZONE PANEL

AUX1

AUX2

L/A

POWER

HEAT

COOL

FAN

STATUS

LEDS

JUMPERS

L/A

EIM

CONNECT OPTIONAL

SENSORS TO

S1 AND S2 TERMINALS

M34250

CONNECT OPTIONAL

SENSORS TO

S3 AND S4 TERMINALS

Connect wireless adapter to ABCD for extended wireless range.

U1, U2 or U3 terminals must be used for geothermal radiant heat. Thermostat

allows 2 stages of radiant heat—geothermal (stage 1) and boiler (stage 2).

“U” terminals are normally open dry contacts when set up for geothermal

radiant heat. You must install a field jumper if radiant heat is powered by

system transformer. Do NOT install a field jumper if radiant heat has its own

transformer.

L/A terminal sends continuous output when thermostat is set to EM HEAT

mode except when set up for Economizer or TOD. See Economizer wiring

section.

O/B

AUX1

AUX2

O/B

AUX1

AUX2

L/A

CHANGEOVER VALVE

BACKUP HEAT

STAGE 1

FAN RELAY

120

VAC

COMPRESSOR

STAGE 1

COMPRESSOR

STAGE 2

BACKUP HEAT

STAGE 2

COMPRESSOR MONITOR

OR ZONE PANEL

GEOTHERMAL RADIANT

HEAT STAGE 1

AIR HANDLER

TRANSFORMER

STATUS

LEDS

JUMPERS

OPTIONAL

JUMPER

POWER

HEAT

COOL

FAN

TO THERMOSTAT

HEAT PUMP

EIM

CONNECT OPTIONAL

SENSORS TO

S3 AND S4 TERMINALS

SENSORS

CONNECT OPTIONAL

SENSORS TO

S1 AND S2 TERMINALS

M34251

EIM wiring guide — geothermal radiant heat

(Prestige and RedLINK VisionPRO models only.)

Typical wiring for geothermal radiant heat, geothermal forced-air, and backup

heat with one transformer.

Wire a maximum of 4 sensors using the S1S4 terminals. S1S4 terminals

can be connected to an indoor sensor, outdoor sensor, discharge sensor,

return sensor, dry contact device to display an alert or an occupancy sensor

for remote setback.

Connect wireless adapter to ABCD for extended wireless range.

Using universal relays to control heating or cooling

(Prestige and RedLINK VisionPRO models only.)

U1/U2/U3 terminals are normally open dry contacts when set up for a stage

of heating or cooling.

You must install a field jumper if the stage of heating or cooling is powered

by system transformer. Do NOT install a field jumper if the stage of heating

has its own transformer.

Dry contact alerts

(Prestige and RedLINK VisionPRO models only.)

EQUIPMENT DAMAGE HAZARD. Do not apply power to S1S4 terminals.

Do not connect a temperature sensor to the S1S4 terminals if set for a dry

contact device.

NOTE: The dry contact device must be rated for low voltage.

If you are not using the S1S4 terminals on the EIM, you can connect them to

a dry contact device to display an alert. Dry contact alerts include Full Drain

Pan, Dirty Filter, Water Leak, System Shutdown, Service Needed, Fan Failure and

Custom Alert. Dry contact device can be normally open (shown in diagram) or

normally closed.

NOTE: You can connect multiple Dry Contact devices in parallel to the S1S4

terminals.

MULTIPLE DRY CONTACT DEVICES

ON ONE SET OF TERMINALS

EIM

M34252B

ONE DRY CONTACT DEVICE

M39128

120

VAC

HEAT STAGE 3,

COOL STAGE 3,

COOL STAGE 4 OR

GEOTHERMAL

RADIANT HEAT

TRANSFORMER

MULTIPLE DRY CONTACT

DEVICES

ON ONE SET OF TERMINALS

ONE DRY CONTACT DEVICE

EIM

M39125

POWERED

HUMIDIFIER

M39129

VAC120

VAC

VAC120

VAC

M39132

FIELD INSTALLED

JUMPER BETWEE

R AND U1

VAC

NON-POWERED

HUMIDFIER

VAC 120

VAC

POWERED

VENTILATOR

M39130

VAC120

VAC

VAC120

VAC

POWERED

DEHUMIDIFIER

M39131

VAC120

VAC

VAC120

VAC

MFCR31587

M39133

FIELD INSTALLED

JUMPER BETWEE

R AND U1

NON-POWERED

VENTILATOR

VAC

VAC 120

VAC

DEHUMIDIFICATION

WITH LOW SPEED FAN

M39134

FIELD INSTALLED

JUMPER BETWEE

R AND U1

VAC 120

VAC

Typical hookup of powered humidiﬁer Typical hookup of non-powered

humidiﬁer

Typical hookup of powered ventilation

Typical hookup of powered dehumidiﬁer

(whole house dehumidifer) Typical hookup of variable speed blow-

er for dehumidiﬁcation in low speed

Typical hookup of non-powered

ventilation

Any combination of universal relays (U1, U2, U3) can be used. They are set in

the thermostat installer setup.

Wire the universal EIM relay to the low speed fan for dehumidiﬁcation control

at the equipment. The EIM relay can be set to be normally open or normally

closed in the thermostat installer setup.

Normally open, dry contacts

Normally closed, dry contacts

Wiring humidification, dehumidification and ventilation

(Prestige and RedLINK VisionPRO models only.)

"U" terminals can be used for humidification, dehumidification or ventilation.

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Home Steuereinheit Handbücher

Honeywell Home

Honeywell Home D15S Bedienungsanleitung

Honeywell Home

Honeywell Home PROWIFI Montageanleitung

Honeywell Home

Honeywell Home H600A Bedienungsanleitung

Honeywell Home

Honeywell Home V4043 Bedienungsanleitung

Honeywell Home

Honeywell Home V1810 Alwa-Kombi-4 Bedienungsanleitung

Honeywell Home

Honeywell Home P5300 Series Bedienungsanleitung

Honeywell Home

Honeywell Home HR91 Bedienungsanleitung

Honeywell Home

Honeywell Home Fire-Lite Alarms MMF-300-10 Bedienungsanleitung

Honeywell Home

Honeywell Home HM700ADVALVE Bedienungsanleitung

Honeywell Home

Honeywell Home Verafix-Cool V9406 Bedienungsanleitung

Honeywell Home

Honeywell Home THM04R3000 Bedienungsanleitung

Honeywell Home

Honeywell Home AQUATROL AQ252 Bedienungsanleitung

Honeywell Home

Honeywell Home NK300SE-VE Montageanleitung

Honeywell Home

Honeywell Home RV 280 Bedienungsanleitung

Honeywell Home

Honeywell Home VC6800 Series Bedienungsanleitung

Honeywell Home

Honeywell Home LTE-21V Bedienungsanleitung

Honeywell Home

Honeywell Home 5800C2W Montageanleitung

Honeywell Home

Honeywell Home BA295S-LF Bedienungsanleitung

Honeywell Home

Honeywell Home 4219 Montageanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung