Honeywell KLN 94 Bedienungsanleitung

-1-

Quick Reference KLN 94

KLN 94 Pages

Airport (APT) Pages

1 Ident, elevation, name, city, state, use

type

2 Latitude/longitude, bearing/radial and

distance

3 Time from UTC, fuel, approaches, radar

environment

4 Runway numbers, length, surface, light-

ing

5 Comm/ILS frequencies

6 User remarks

7 DP/STAR procedures

8 Approach procedures

VOR Pages

1 Ident, frequency, name, lat/long

2 Magnetic station declination,

bearing/distance

NDB Page

1 Ident, frequency, name, lat/long, bear-

ing/distance

Intersection (INT) Pages

1 Ident, lat/long, bearing/distance, DME

designation (for ILS DMEs)

2 Location relative to VOR

User-defined Waypoint (USR) Pages

1 Ident, lat/long, bearing/distance

2 Location relative to VOR

3 User remarks

Active Waypoint (ACT) Pages

Waypoint pages for active flight plan

waypoints and/or the direct-to waypoint.

(Pull right inner knob out to scan FPL 0 way-

points).

Navigation (NAV) Pages

1 Active waypoint/leg, CDI, crosstrack

correction, CDI scale, VNAV status,

bearing, ETE

2 Present position (lat/long and radial/

distance)

3 Present time, departure time, flight time,

ETE & ETA at destination

4 Moving map

Flight Plan (FPL) Pages

0 Active flight plan

1-25 Stored (numbered) flight plans

Setup (SET) Pages

1 Position initialization for GPS receiver

2 Date, time, and time zone initialization,

mag var

3 Database update

4 Nearest airport criteria

5 SUA alert enable/disable

6 SUA alert/map

7 Map setup for aero data

8 Map setup for land data

9 Low voltage warning

10 Turn anticipation enable/disable

11 Default first waypoint character

12 Barometric pressure units

13 Altitude alerting

14 QuickTune™ default

Auxiliary (AUX) Pages

1 GPS state, GPS altitude, EPE

2 GPS signal status

3 RAIM prediction

4 Trip planning for distance, bearing, ESA,

and ETE

5 Trip planning for fuel requirements

6 Pressure altitude

7 Density altitude

8 True airspeed (TAS)

9 Winds aloft

10 Alarm/timer

11 Sunrise/sunset

12 List of user-defined waypoints

13 List of airports and user waypoints with

stored remarks

14 Software versions

15 *Fuel required, fuel on board, landing

fuel

16 *Fuel reserve, extra fuel

17 *Fuel endurance, range, efficiency

18 *Fuel flow

19 *Cumulative fuel used

20 *TAS, Mach

21 *SAT, TAT, pressure alt, density alt

* Page only displayed if appropriate equip-

ment is interfaced with KLN 94.

Bendix/King®

GPS Navigation System

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 4

KLN 94 INSTRUMENT APPROACH REFERENCE

WARNING: Make sure that you have practiced instrument

approaches with the KLN 94 in VFR weather before attempting to fly

approaches in IMC.

APPROACH SEQUENCE

1. Select an approach and load into FPL 0

a. PRESS P. Choose "Select Approach?"

b. SELECT airport on PROC 2 page

c. SELECT an approach/IAF from APT 8 page. Choose "Vectors" for

radar vectors

d. CHANGE an approach using above procedure

e. DELETE approaches on the FPL 0 page.

2. Get established on the final approach course.

a. VERIFY APR ARM (or TERM) is annunciated within 30 nm of

destintion.

b. SELECT the NAV 4 page.

c. SELECT OBS mode for procedure turns and holding patterns. Use

OBS mode until inbound to the FAF.

d. SELECT LEG mode for radar vectors and NoPT routes including

DME arcs. LEG mode is mandatory from the FAF to the MAP.

e. PRESS Pand ACTIVATE Vectors from PROC 1 page for radar

vectors.

3. At or before 2 nm from the FAF inbound:

a. SELECT the FAF as the active waypoint.

b. SELECT LEG mode.

4. At 2 nm inbound to the FAF:

a. VERIFY APR ACTV (or APR) annunciated.

5. At the FAF if APR ACTV not annunciated:

a. DO NOT DESCEND.

b. EXECUTE MISSED APPROACH.

NOTE: There is no automatic leg sequencing at the MAP.

6. After the MAP:

a. FLY the exact published missed approach procedure from the

approach charts.

b. PRESS D. Verify automatic selection of the first waypoint of the

missed approach procedure (usually the missed approach holding

point). Change it if desired.

-2-

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 5

APPROACH TIPS

1. The database must be up to date.

2. Only one approach can be in the flight plan at a time.

3. Use the Pbutton to initiate approach and IAF selections.

4. Data cannot be altered, added to or deleted from the approach proce-

dures contained in the database. (DME arc intercepts may be relocated

along the arc through the NAV 4 page or FPL 0 page.)

5. To change a DP, STAR or approach, select a new one using the nor-

mal procedure for selecting and loading a procedure.

6. To delete a DP, STAR or approach, select the FPL 0 page, place the

cursor over the name of the DP, STAR or approach, press Eand

then F.

7. Some approach waypoints in the database may not appear on the

approach plates (in some cases this includes the FAF)!

8. Waypoint suffixes attached to some approach waypoints: i - IAF, f -

FAF, m - MAP, h - missed approach holding fix.

9. Use the NAV 4 page for flying approaches.

10. At the time of installation the KLN 94 is configured to annunciate either

(1) APR ARM and APR ACTV or (2) TERM and APR. The two sets

mean exactly the same.

11. At 30 nm from the destination airport the KLN 94 will go into APR ARM

(or TERM) if there is an approach in the flight plan. Left/right D-bar scal-

ing will change from ±5.0 nm to ±1.0 nm over the next 30 seconds.

12. If the approach includes a DME arc, the DME arc intercept point will be

a) on your present position radial off the arc VOR at the time you select

an arc IAF, or b) the beginning of the arc if currently on a radial beyond

the arc limit. To adjust the arc intercept to be compatible with a radar

vector, bring up the first waypoint of the arc in the NAV 4 page scan-

ning field (or under he cursor on the FPL 0 page), press E, then

F. Fly the arc in LEG. Adjust the HSI or CDI course pointer with ref-

erence to the desired track value on the NAV 4 page (it will flash when

the pointer needs to be adjusted). Left/right D-bar information is rela-

tive to the arc. Displayed distance is not along the arc but straight to the

active waypoint. (The ARC radial is also displayed on the NAV 4 page.)

13. Two nm from the FAF inbound and in LEG, the KLN 94 will go into APR

ACTV (or APR) and the D-bar scaling will begin changing from ±1.0 nm

to ±0.3 nm.

-3-

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 6

-4-

14. APR ARM to APR ACTV (or TERM to APR) is automatic provided all

of the following are satisfied:

a) In APR ARM (normally automatic).

b) In LEG mode!

c) FAF is the active waypoint!

d) Within 2 nm of the FAF.

e) Outside the FAF.

f) Inbound to the FAF.

g) RAIM is available. (For early prediction go to AUX 3 page.)

15. RAIM availability is mandatory for approach operation.

16. APR ACTV (or APR) mode is mandatory for approach opertion.

17. DIRECT-TO operation between the FAF and MAP cancels approach

ACTV (or APR). Fly the missed approach in APR ARM (or TERM).

18. Flagged navigation inside the FAF due to a RAIM problem may usually

be restored by pressing the Pbutton to change from ACTV to ARM

(or APR to TERM). A message is provided as a reminder. Fly the

missed approach procedure.

19. Instrument approaches using the KLN 94 may be essentially automat-

ic starting 30 nm out (with manual baro setting update) or it may

require judicious selection of the OBS and LEG modes.

PAGE MESSAGES

Messages that could appear during approach operations. Refer to the

Pilot's Guide for a complete list of messages.

XXXXX Deleted

From FPL 0 -- A pre-existing waypoint was deleted from FPL 0 because the

same waypoint was in the Approach/DP/STAR just loaded into FPL 0.

APR ACTV Annunicator

Fail -- Indicates an external annunciator drive circuit failure. Discontinue

approach operation unless already on final approach inside the FAF.

Adj Nav Crs to XXX°-- Manually adjust the mechanical HSI or CDI to the

indicated value.

APR ARM Annunicator

Fail -- Indicates an external annunciator drive circuit failure. Discontinue

approach operation unless APR ACTV is annunciated.

Arm GPS Approach -- Manually arm approach mode. (A reminder given 3

nm from the FAF if the approach mode was disarmed manually with an

optional GPS approach arm switch.)

Bad Satellite Geometry

And RAIM Not Available -- Can appear in approach ACTV (or APR) mode

only. Integrity monitoring is lost and satellite geometry is degraded. Can be

followed by a NAV flag.

MAP

FAF

70°

2 nm

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 7

PAGE MESSAGES Continued

Bad Satellite Geometry

See EPE on AUX 1 page -- Integrity monitoring is lost and the estimated

position error is greater than allowed for the current phase of flight. Cross

check the position with other on-board equipment every 15 minutes.

Check APR ACTV

Annunciator -- Indicates an overcurrent condition in the external annuncia-

tor circuit. Discontinue approach operation unless already on final approach

inside the FAF.

Check APR ARM

Annunciator -- Indicates an overcurrent condition in the external annuncia-

tor circuit. Discontinue approach operation unless APR ACTV (or APR) is

annunciated.

Enable Turn

Anticipation For

GPS Approach -- Turn anticipation has been disabled on the SET 10 page.

For proper approach operation, it should be enabled on the SET 10 page.

GPS Course is XXX° -- Displays the new desired track when GPS is not

displayed on the primary indicator.

If Required Select OBS -- Use OBS mode for holding patterns or proce-

dure turns. Appears 4 nm from a waypoint that normally would require the

OBS mode.

If Using Procedure

Turn Reduce Speed

To Remain Within

Protected Area -- The aircraft’s flight path may extend beyond the protect-

ed airspace for the procedure turn if the aircraft’s present ground speed is

maintained (ORS 02 and higher).

Press ALT To Set Baro -- A reminder given 30 nm from the destination air-

port to update the barometric setting.

Press PROC Button Now For Navigation -- After a NAV flag in approach

ACTV (or APR) mode, press Pbutton to restore navigation for the

missed approach. (Integrity monitoring is less critical in approach ARM (or

TERM) mode so navigation may be restored.)

RAIM Not Available

APR Mode Inhibited

Predict RAIM on AUX 3 --RAIM is predicted to not be available at either the

FAF or the MAP. Determine when RAIM will be available on the AUX 3

page. Integrity monitoring is required for approach operation.

RAIM Not Available

Cross Check Position --Integrity monitoring is absent. Compare the GPS

position with other on-board navigation equipment.

-5-

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 8

PAGE MESSAGES Continued

RAIM Position Error

Cross Check Position--RAIM has detected a problem with a satellite.

Compare the GPS position with other on-board navigation equipment.

Redundant WPTs in FPL

Edit Enroute WPTs

As Necessary--Examine the active flight plan and remove those way-

points that occur both in the en route and the approach or DP/STAR sec-

tions of the flight plan.

SCRATCHPAD MESSAGES

Messages that could appear during approach operations. Refer to the

Pilot's Guide for a complete list of messages.

CRS

XXX°--When in OBS mode, manually adjust the HSI or CDI course pointer

to the prescribed value to provide direct-to navigation.

Fpl Is

Full--The KLN 94 cannot add any more waypoints to the flight plan.

Invalid

Add--You cannot add waypoints to the approach sequence.

Invalid

Del--You cannot delete waypoints from the approach sequence.

No Appr

at Apt -- An airport has been entered on the PROC 2 page that does not

have an approach in the database.

No Apr In Fpl --No approach has been loaded into the flight plan when

the APR ARM button is pressed.

No Intcpt --The aircraft's actual track does not intersect with the DME arc.

Alter course so that the actual track does intercept the arc.

D Base Expire --A reminder that the database is out of date.

NAV 4 (MOVING MAP) PAGE TIPS

• To display the NAV 4 page when on any other page, pressRor M.

• To scan through waypoints in scanning window, pull out and turn the

right inner knob. Active flight plan waypoints are displayed in green.

Non-flight plan waypoints are displayed in white. With desired waypoint

displayed in scanning window, press Dand Fto go direct-to the

selected waypoint OR press Fto display the waypoint page for the

selected waypoint (ORS 02 and higher).

-6-

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 1

• To temporarily declutter the map, press Eonce to deselect land

data, press Ea second time to declutter aero data. To restore,

press Eagain or leave the NAV 4 page and return to it.

• To configure what information is displayed on the map, press the M

button, select Setup Aero Data? or Setup Land Date Menu? and

press the Fbutton to bring up the appropriate Setup page (SET 7

for aero data and SET 8 for land data). The range selected on these

SET pages is the maximum range scale that the selected item will be

displayed on the map.

• To change the map orientation, press the Mbutton, move the cursor

over item 3 and turn the right inner knob to select the desired orienta-

tion:

N↑= North up

TK↑= Actual track up (when groundspeed > 2 kts)

HDG↑= Heading up (if heading supplied to the KLN 94)

DTK↑= Desired track up

• To change the map scale factor:

1. Press theRbutton. The top half increases the map scale and the

bottom half decreases the map scale. The scale is displayed in the

bottom left part of the map.

2. For terminal area operations select AUTO scale factor by pressing

theRbutton for 2 seconds.

• To change the navigation information shown in the lower left corner of

the display:

1. Press the Bbutton.

2. Use the right outer knob to move the cursor to line 4 or line 5 in the

the lower left corner.

3. For line 4, use the right inner knob to select between actual track

(TK), bearing, radial, or groundspeed.

4. For line 5, use the right inner knob to select between groundspeed,

ETE, crosstrack correction, or VNAV status.

-7-

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 2

Honeywell International Inc.

Business & General Aviation

23500 West 105th Street

Olathe, Kansas 66061

FAX (913) 712-1302

TELEPHONE (913) 712-0400

Rev 2 3/2001 006-18228-0000 N

SUMMARY OF OPERATION

• Emergency Nearest Airport Search - Press Gthen F.

• Operation of right knobs - Cursor on

• Press Bbutton. With the cursor on, outer knob controls cursor

location and inner knob selects the character.

• With the inner knob in, make selection character by character.

• With inner knob out, make selection by scanning through the data-

base alphabetically.

• Operation of right knobs - Cursor off

• Outer knob selects page type (APT, VOR, etc.)

• Inner knob selects specific page (APT 1, APT 2, etc.)

• Direct To operation

• Press Donce. Enter desired wpt using right concentric knobs,

press Fto view wpt info, press Fto confirm.

• Alternatively, highlight desired wpt in flight plan, then press D,

then press Fto confirm.

• To center D-bar. With non-wpt page displayed press Dthen F.

• To cancel direct to operation press D, then E, then F.

KLN 94 BUTTONS

CDisplays the message page

HChanges between Leg and OBS navigation modes

ADisplays the altitude pages, ALT 1 and ALT 2

GSelects the nearest APT, VOR, NDB, INT, USR, SUA, FSS, or CTR

DInitiates a direct-to operation

ECancels operations

FApproves an operation

PInitiates the selection of or the changing of an approach, DP, or

STAR. Activates vectors-to-final.

RIf on the NAV 4 (map) page, changes the map range scale. If on

any other page, brings up the NAV 4 page.

MIf on the NAV 4 (map) page, brings up the map menu for configuring

map. If on any other page, brings up the NAV 4 page.

KLN 94 Quick Ref R2 4/3/02 1:55 PM Page 3

Inhaltsverzeichnis

Andere Honeywell Auto-Navigationssystem Handbücher

Honeywell

Honeywell BENDIX/KING KCS55 Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Pioneer

Pioneer MZ360500EX Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Pioneer

Pioneer AVIC-Z920DAB Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung

Mazda

Mazda 107006AN Bedienungsanleitung