Honeywell BSM Montageanleitung

K14864V3 9/10 Rev. A

BSM

Battery Sense Module

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The Honeywell Battery Sense Module is a control panel

accessory that is used to monitor and report the backup

battery status. Its features are:

Monitors and reports for one or two batteries.

Detects and reports low battery conditions.

Detects and reports if a battery is removed.

Provides deep discharge battery protection if AC

power is lost and the backup battery voltage falls

below a safety threshold of 9.5 to 10 volts.

Additional modules can be used for those control panels

that use additional batteries.

PACKAGE CONTENTS

The following items are included:

Battery Sense Module with bracket

Battery Harness (qty 2)

Summary of Connections label

SPECIFICATIONS

Physical: 3-1/8” L x 2-3/4” W x 3/4” H

(80mm x 70mm x 20mm)

Electrical:

Input Voltage: 12VDC nominal (from control panel)

Input Current: 20mA (max used by BSM)

Current Handling Capability: 2.3A maximum

(Control panel load must not exceed 2.3A.)

INSTALLATION

1. Select a suitable area in the control panel where

the mounting will not interfere with testing or

servicing of other components.

2. Clip the Battery Sense Module to the cabinet edge.

CONNECTIONS

1. Refer to the Connections Diagram on other side.

When connecting leads, support the module to

prevent stress on the circuit board.

2. Connect the module's power leads to the control

panel's 12VDC backup battery power terminals.

3. Connect backup battery A to the module. Then

connect backup battery B (if present) to the module.

4. If only one backup battery is being used, depress

the ENROLLMENT switch to toggle the Battery

Sense Module to sense only one battery.

ULC

When used with one battery and the total

load is greater than 1.5A, jumper the

Battery A terminals and the Battery B

terminals on the Battery Sense Module to

the backup battery.

5. For non-Honeywell control panels, connect the

ZONE OUT to an unused control panel zone. (Do

not use a fire zone.)

Note: For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT terminal on

the BSM. The Honeywell control panel will

automatically detect a low or missing battery

through the panel's battery cable.

6. Affix the supplied Summary of Connections label to

the inside of the control panel.

CONFIGURATION

1. Refer to the control panel's installation guide for

details on fault monitoring.

2. For non-Honeywell control panels, program the

connected zone for the Battery Sense Module to

detect an active high fault condition.

ZONE OUT

BAT

BSM-001-V0

B AT. A PANEL

B AT. B

DOCUMENTATION AND ONLINE SUPPORT

For the latest documentation and online support information, please go to:

http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY

For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ÊK14864V3cŠ

K14864V3 9/10 Rev. A

STATUS LEDs (A and B)

STEADY ON Battery is present and good.

BLINKING Battery is programmed to be

present, and is NOT present.

OFF Battery is NOT programmed to be

present.

ENROLLMENT Switch

Default condition is for 2

batteries.

Depress once for 1 battery.

To the control panel battery terminals.

To Battery A terminals.

To Battery B terminals.

To a non-Honeywell

control panel zone for

fault monitorin

Note:

For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT ter-

minal on the BSM. The Honeywell

control panel will automatically detect

a low or missing battery through the

panel's battery cable.

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell V5421C Bedienungsanleitung

Honeywell

Honeywell S4560A Bedienungsanleitung

Honeywell

Honeywell V5055A-E Bedienungsanleitung

Honeywell

Honeywell PEHA PHC Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell SM110 Bedienungsanleitung

Honeywell

Honeywell MCV2000AA Montageanleitung

Honeywell

Honeywell Prestige THX9421R02 Bedienungsanleitung

Honeywell

Honeywell Exi-/MaxLED T2 Bedienungsanleitung

Honeywell

Honeywell VQ400 Series Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT IDP-Control-6 Bedienungsanleitung

Honeywell

Honeywell SUPER TRADELINE VR8300A Bedienungsanleitung

Honeywell

Honeywell VF5000 Series Bedienungsanleitung

Honeywell

Honeywell VR8205 Bedienungsanleitung

Honeywell

Honeywell AlarmNet 7847i-E Montageanleitung

Honeywell

Honeywell SUPER TRADELINE S8610U Bedienungsanleitung

Honeywell

Honeywell SK-Mon-10 Bedienungsanleitung

Honeywell

Honeywell AlarmNet 7810iR Bedienungsanleitung

Honeywell

Honeywell TELEPHONE ACCESS MODULE W8735D Bedienungsanleitung

Honeywell

Honeywell PEHA 940 AMA Bedienungsanleitung

Honeywell

Honeywell DIAL-SET DS05C Bedienungsanleitung

Honeywell

Honeywell NOTIFIER FCM-1 Bedienungsanleitung

Honeywell

Honeywell LYNXDM-GSM Montageanleitung

Honeywell

Honeywell ADEMCO 4204 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung