Honeywell Fire-lite FFT Bedienungsanleitung

FFT

Fire Fighter Telephone Module

Product Installation Drawing

Document 52246 RevA 1/16/08 ECN 07-873

CAUTION! Make sure to observe all of the following precautions:

• Remove all power (AC and DC) before installing or removing any modules since damage to components

may occur if power remains applied.

• Circuit boards contain static-sensitive components. Always ground yourself with a proper wrist strap

before handling any boards so that static charges are removed from the body. Use static suppressive

packaging to protect electronic assemblies.

FFTReplacement

1. Make certain thatAC and DC power have been removed from the panel.

2. Unplug the terminal block connectors from TB1, TB2 and TB3 located on the top edge of the defective FFT board

(label to ensure reinstallation in correct positions).

3. Unplug the panel telephone handset from Phone Jack J1 located on bottom center of the defective FFT board.

4. Remove two mounting screws which hold the defective FFT board to the mounting bracket standoffs and set aside.

5. Carefully lift the defective FFT board from the slot in the bottom of the mounting bracket.

6. Remove the ribbon cable connectors from J2 on the right side of the board and J3 on the back of the defective FFT

board.

7. Connect cable between J2 on the new FFTboard and P5 on Zone Split Audio Panel main circuit board as illustrated

below.

8. If telephone call-ins are to be annunciated on the ZPM, connect cable between J3 on the FFT and P4 on the back

of the ZPM(K) module. Note that the J3 and P4 ribbon cable connectors are keyed to prevent incorrect

installation. Refer to following illustration for connector locations.

The FFTFire Fighter Telephone Module provides supervision,

annunciation and control for local and remote telephone handsets as

well as an optional remote microphone.

Audio Panel with Zone Split

Make certain that the ribbon cable is

installedwith thered stripeoriented

asillustrated below.

red stripe

Document 52246 RevA ECN 07-873 1/16/08

Standoff Standoff

Slot

Mounting Bracket

FFT

Terminal Block Connectors

J2 (on side)

TB1TB2TB3

J3 (on back)

RibbonCable

Connectors

SW1 J1

9. Insert the bottom of the new FFT board in the slot located in the bottom right of the mounting bracket as indi-

cated in illustration below.

10. Secure the module to the mounting bracket standoffs with the two mounting screws.

11. Wire the terminal blocks TB1,TB2 and TB3 as described in the illustration below. Plug the terminal block

connectors which were disconnected in step 2 into TB1, TB2 andTB3 located on the top edge of the FFT.

12. Plug the panel telephone handset into Phone Jack J1 on bottom center of FFT.

13. Set switch SW1 to correct position. SW1 positioned to the left (as illustrated below) indicates that the remote

microphone is installed. SW1 positioned to the right indicates that a remote microphone is not installed.

14. Set switch SW2 to correct position. SW2 positioned up (as illustrated below) indicates that the audio wiring to

the Remote Page Jack is configured for 2-wire Class B.

15. ReapplyAC and DC power

16. Program the host FACPfor proper operation with the Audio Panel

17. Test the panel for proper operation.

SW2

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell TS131 Bedienungsanleitung

Honeywell

Honeywell IntelliDoX Bedienungsanleitung

Honeywell

Honeywell KT73 Bedienungsanleitung

Honeywell

Honeywell RV280 Bedienungsanleitung

Honeywell

Honeywell DIAL-SET DS05C Bedienungsanleitung

Honeywell

Honeywell MDC108200 Bedienungsanleitung

Honeywell

Honeywell R7120D Bedienungsanleitung

Honeywell

Honeywell BA295STN-11/2C Bedienungsanleitung

Honeywell

Honeywell AlarmNet 7847i-E Montageanleitung

Honeywell

Honeywell ADEMCO VA8201 Montageanleitung

Honeywell

Honeywell CIPer 30 Bedienungsanleitung

Honeywell

Honeywell TM300 Bedienungsanleitung

Honeywell

Honeywell VCZA Series Bedienungsanleitung

Honeywell

Honeywell SM152 AA Series Bedienungsanleitung

Honeywell

Honeywell V4730B Bedienungsanleitung

Honeywell

Honeywell DR 300 Bedienungsanleitung

Honeywell

Honeywell Braukmann BV300 Bedienungsanleitung

Honeywell

Honeywell MDC108200 Bedienungsanleitung

Honeywell

Honeywell C7110C1040 Bedienungsanleitung

Honeywell

Honeywell TRADELINE VR8345M Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell RV283P Bedienungsanleitung

Honeywell

Honeywell TC810E1040 Bedienungsanleitung

Honeywell

Honeywell PW6K1R1E Bedienerhandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung