Honeywell NOTIFIER ASY-01-044-NIM Bedienungsanleitung

1 Product Overview

This Installation sheet describes how to mount and connect:

A Network Interface Module (NIM) to a Fire Panel

The Network Interface Module stores data received from the Networks Cards. The stored data is accessed by the

AFP-2800 and presented to the operator.

NOTE: The Network Card is supplied separately.

WARNING:

Remove all power sources to equipment while connecting the components.

Leave the external, main power breaker OFF until installation of the components are

complete.

2 Installation

1. Unplug from the PSI board:

a. The 27 Volt PSU Power Supply Cable running from the PSI board - see Connection Schematic.

b. The 4 - Way Power Cable running from the Termination board - see Connection Schematic.

c. The Battery Power Supply - see Connection Schematic.

d. The 10 - Way Ribbon Cable running to the Termination board - see Connection Schematic.

9 Columbia Way

Baulkham Hills, NSW 2153

PH 02-9894-1444 • FAX 02-9894-4193

www.notifier.com

ASY-01-044 - NIM

Product Installation Sheet

DOC

061

ECN12

0032

/201

Rev:

1.0

2. Remove the 4 M3 x 8mm screws connecting the PSI mounting bracket to the Loop Interface Module

(LIM)

Figure 2-1: Removal of the M3 x 30mm Spacers, and the M3 x 20mm Spacers

NOTE: Do not remove the M3 Screws connecting the PSI Mounting Bracket to the PSI board.

3. Replace the existing M3 x 20mm Spacers and the M3 x 30mm Spacers with 4 M3 x 25mm Spacers

(#11171)

Figure 2-2: Mounting NIM to LIM with M3 x 25mm Spacers

4. Replace the 40 - Way Ribbon Cable connected to the LIM ‘IN’ Port with the 100mm 40 - Way Ribbon

Cable (#10202) - see Connection Schematic.

5. Connect:

a. The 100mm 40-Way Ribbon Cable (#10202) to the NIM ‘OUT’ Port

b. The 40-Way Ribbon Cable (#10200) to the Termination Board from the NIM ‘IN’ Port - see

Connection Schematic.

c. The C30 3-Way Wafer Cable (#10206) to the NIM 24V – 0V – 5V Port

d. The loose end of the C30 3-Way Wafer Cable (#10206) to the Top Power Port on the

Termination Board - see Connection Schematic.

e. The NUP Cable (#11637) to the NIM NUP Port - see Connection Schematic.

f. The loose end of the NUP Cable to the Network Card NUP Port.

6. Set the NIM Dip-switches to:

1 2 3 4

ON ON OFF OFF

Table 1: NIM Dip-switch Settings

7. Position the NIM (#11628) over the M3 x 25mm Spacers (#11171).

8. Secure the NIM at the top (#11628) with 2 additional M3 x 25mm Spacers (#11171)

9. Secure the bottom of the NIM with the 2 M3 x 15mm Spacers (#11828)

10. Position the PSI board assembly over the M3 x 25mm Spacers (#11171) and the M3 x 15mm Spacers

(#11828)

11. Secure the PSI mounting bracket to the bottom Spacers with 2 M3 x 8mm Screws (#2316)

12. Screw the top part of the PSI board to the top spacers with 2 M3 x 8mm Screws (#2316)

Figure 2-3: Mounting PSI board to NIM

3 Connection Schematic

Figure 3-1: NIM, LIM and PSI Schematic

4 Components

Part No. Description Qty

2316 Screw Sems - Pan Philip Zinc, M3 X 8mm w/Flat Small

S/Washer 6

10200 Cable-Assembly, C24 - 40 Way X 440mm 1

10202 Cable-Assembly, C26 - 40 Way X 100mm 1

10206 Cable-Assembly, C30 - 3 Way X 330mm 1

11171 M3 tapped spacer x 25mm - M/F, hexagonal, nickel finish 6

11628 Network Interface Mod. (NIM) - IFS-725A 1

11637 NUP Cable - 5 Way, 780mm Long 1

11828 M3 tapped spacer x 15mm - M/F, hexagonal, nickel finish 2

DOC-03-061 NIM Installation Sheet 1

Table 2: NIM, LIM and PSI Components

5 Supplemental Documentation

For information on... Refer to... Doc No.

Programming and Operating a NIM AFP-2800-2802 Manual DOC-01-010

Table 3: Supplemental Documentation

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell V1810 Alwa-Kombi-4 Bedienungsanleitung

Honeywell

Honeywell SOMAT39 Bedienungsanleitung

Honeywell

Honeywell D06F Bedienungsanleitung

Honeywell

Honeywell V4295A,S Bedienungsanleitung

Honeywell

Honeywell CF3680 Bedienungsanleitung

Honeywell

Honeywell R7140G Bedienungsanleitung

Honeywell

Honeywell TELEPHONE ACCESS MODULE W8735D Bedienungsanleitung

Honeywell

Honeywell DCCC6500 Bedienungsanleitung

Honeywell

Honeywell BA295I Bedienungsanleitung

Honeywell

Honeywell AlarmNet GSMBR Montageanleitung

Honeywell

Honeywell WV8840B Bedienungsanleitung

Honeywell

Honeywell MDC108200 Bedienungsanleitung

Honeywell

Honeywell RV284 Bedienungsanleitung

Honeywell

Honeywell S4567A 1001 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4229 Montageanleitung

Honeywell

Honeywell L6190A Bedienungsanleitung

Honeywell

Honeywell L4017 Bedienungsanleitung

Honeywell

Honeywell Galaxy 2 Series Bedienungsanleitung

Honeywell

Honeywell Braukmann T100A Bedienungsanleitung

Honeywell

Honeywell VE4000 Series Bedienungsanleitung

Honeywell

Honeywell L4068 Bedienungsanleitung

Honeywell

Honeywell Silent knight 5895XL Betriebsanleitung

Honeywell

Honeywell Satronic DMG 973 Bedienungsanleitung

Honeywell

Honeywell EIM Installationsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung