Honeywell BC7000L1000 Handbuch

CONVERSION WIRING DIAGRAMS

FOR BC7000L1000

The diagrams and instructions contained in this booklet are for converting the following model

programmers to BC7000 Microcomputer Based Burner Control System.

TABLE OF CONTENTS Page

Section l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...2

Fireye C, D, and E-Series

Section II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...6

Fireye P-Series

Section III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Honeywell R4126, R4127, R4181

Section lV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Honeywell R4140, R4150 with 20 Terminal Subbase (120 V only)

Section V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...29

Honeywell R4150 with 13 or 15 Terminal Subbase

1. Installer must be a trained, experienced, flame safeguard control service technician.

2. Disconnect power supply before beginning installation to prevent electrical shock and

equipment damage.

3. All wiring must comply with applicable local electrical codes, ordinances, and regulations.

4. Voltage and frequency of the power supply and flame detector(s) connected to this control

must agree with those marked on the device.

5. Loads connected to the control terminals must not exceed those listed in the SPECIFI-

CATIONS section.

6. All external timers must be listed or component recognized by authorities having

jurisdiction, for the specific purpose for which they are used.

7. Perform all required checkout tests after installation is complete.

IMPORTANT

For on-off, gas-fired systems, some authorities having jurisdiction prohibit the wiring of any

limit or operating contacts in series with the main fuel valve(s).

P.G.

Rev. 6/89

Form Number 66-6002—4

©Honeywell Inc. 1989

SECTION I

FIREYE C, D, E-SERIES CONTROL

120 V ONLY

DIRECTIONS:

1. Disconnect all power to programmer.

2. Remove old programmer from subbase (trade-in to Honeywell Authorized Flame Safeguard

Distributor).

3. Mark all wires on subbase; i.e., wires connected to terminal “D” should be marked “D.”

Disconnect wires as they are marked.

4. Remove old subbase.

5. Mount Q520A subbase.

6. Connect wires to subbase per attached cross reference. Pay close attention to footnotes. For

example: To convert a Fireye 70D10 to a BC7000, the wire marked “P” would connect to

terminal #3 on the Q520. The wire marked “8” would connect to Q520 terminal #15.

7. The symbol “ “ designates a footnote. Study these footnotes carefully.

8. Plug in the BC7000. Make sure you select the proper amplifier, detector and program module

for the application.

E1214A

FIREYE 70D10/26CF6-5022/26 CU6-5065

EP160/EP161/EP170

BC7000L/PM720L2004 or 1030

E1215B

FIREYE 24CJ5 - 5010/5011/3010/3011

25CU6 5062/5063/RS-2E

70D30/26CF6 5020/5021/1010/1011

EP380/EP381/EP390

BC7000L/PM720M2002

E1216E

FIREYE 24CJ5 5015

70D20/26CF6 5023/25 CU65055

EP260/EP261/EP270

BC7000L/PM720G2005

SECTION II

FIREYE P-SERIES CONTROLS

120 V ONLY

DIRECTIONS:

Disconnect all power to programmer.

Remove old programmer from subbase (trade-in to Honeywell Authorized Flame Safeguard

Distributor).

Mark all wires on subbase; i.e., wires connected to terminal “D” should be marked “D.”

Disconnect wires as they are marked.

Remove old subbase.

Mount Q520A subbase.

Connect wires to subbase per attached cross reference. Pay close attention to footnotes. For

example: To convert a Fireye 26RJ81016 to a BC7000, the wire marked “B” would connect to

terminal #10 on the Q520. The wire marked “W” would connect to Q520 terminal #14.

The symbol “ “ designates a footnote. Study these footnotes carefully.

Plug in the BC7000. Make sure you select the proper amplifier, detector and program module

for the application.

E1221A

FIREYE 26RJ8 1016, 1016T

26RJ8 1012, 1012T, 6012, 6012T

BC7000L + PM720G2005

E1693

FIREYE 25RLJ84580

BC700L + PM720L1030

E1217B

FIREYE 25RU8 6560, 6570,6580

26RJ8 6060, 6070,6080, 6160 TO

BC7000L + PM720L1030

E1218A

FIREYE 29RF5 1001, 1009, 6009 TO BC7000L + PM720G2013

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell Centra Line HAWK 8000 Installations- und Betriebshandbuch

Honeywell

Honeywell S9201A1010 Bedienungsanleitung

Honeywell

Honeywell Pressuretrol P7810C Bedienungsanleitung

Honeywell

Honeywell MS4120F Bedienungsanleitung

Honeywell

Honeywell ML6194 Bedienungsanleitung

Honeywell

Honeywell Spyder PUL1012S Bedienungsanleitung

Honeywell

Honeywell ML6420A3072 Bedienungsanleitung

Honeywell

Honeywell DBC2000E10 Series Bedienungsanleitung

Honeywell

Honeywell VC6613AJ1000 Bedienungsanleitung

Honeywell

Honeywell HON 380 Bedienungsanleitung

Honeywell

Honeywell DC1010 Bedienungsanleitung

Honeywell

Honeywell CN34 Series Bedienungsanleitung

Honeywell

Honeywell L7124U Bedienungsanleitung

Honeywell

Honeywell Fire Sentry FS7-130-SX Bedienungsanleitung

Honeywell

Honeywell SHC Series Bedienungsanleitung

Honeywell

Honeywell HUPF Series Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell FR124 Bedienungsanleitung

Honeywell

Honeywell HC900 Betriebsanleitung

Honeywell

Honeywell LKS 160 Bedienungsanleitung

Honeywell

Honeywell S9360B Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Bedienungsanleitung

Honeywell

Honeywell HCE80 Betriebsanleitung

Honeywell

Honeywell Spyder 7 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch