Honeywell CN05 Series Bedienungsanleitung

CN05, CN10 SERIES

NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR

FLOATING AND TWO-POSITION CONTROL

PRODUCT DATA

GENERAL

This non-spring return direct-coupled damper actuator

provides floating and two-position control for:

• air dampers,

• VAV units,

• air handlers,

• ventilation flaps,

• louvers, and

• reliable control for air damper applications with up to 10

sq ft / 44 lb-in. (5 Nm) and 20 sq ft / 88 lb-in. (10 Nm)

(seal- less damper blades; air friction-dependent).

FEATURES

• Declutch for manual adjustment

• Adjustable mechanical end limits

• Removable access cover for direct wiring

• Mountable in any orientation

• Rotation direction and service/OFF switch

SPECIFICATIONS

Supply voltage

CN6105/CN6110 24 Vac/dc -15%/+20%, 50/60 Hz

CN4605/CN4610 230 Vac -15%/+20%, 50/60 Hz

Nominal voltage

CN6105/CN6110 24 Vac/dc, 50/60 Hz

CN4605/CN4610 230Vac, 50/60 Hz

All values stated hereinafter apply to operation under

nominal voltage conditions.

Power consumption

CN6105/CN6110 5 VA / 2 W

CN4605 22 VA / 2 W at 50 Hz

CN4610 25 VA / 2 W at 60 Hz

Ambient limits

Ambient operating limits -5...+140 °F (20...+60 °C)

Ambient storage limits -22...+176 °F (-30...+80 °C)

Relative humidity 5...95%, non-condensing

Safety

Protection standard IP54

Protection class II as per EN 60730-1

Overvoltage category II

Lifetime

Full strokes 60000

Repositions 1.5 million

Mounting

Round damper shaft 3/8 in…5/8 in.

Square damper shaft 1/4 in…1/2 in.; 45° steps

Shaft length min. 1-5/8 in.

End switches (when included)

Rating Class II

Triggering points 5° / 85°

Torque rating 44 lb-in. (5Nm) / 88 lb-in. (10 Nm)

Runtime for 90°

CN6105 90 sec (dc / 60 Hz ac)

CN6110 90 sec (dc / 50 Hz ac)

CN4605 65…110 s (60/50 Hz)

CN4610 65…140 s (60/50 Hz)

Rotation stroke 95° + 3°

Dimensions see “Dimensions” on page 6

Weight (without cables) 1 lbs.

Noise rating 35 dB(A) max. at 1 m

40 dB(A) for 230 Vac at

65 sec runtime

Certification

CN6105/CN6110 CE & UL

CN4605/CN4610 CE

CN0B-0544CH33 R0805B

PRODUCT IDENTIFICATION SYSTEM

C-Electrical Motor

N-Fail Safe Function (Non-Spring Return)

61-24V Floating Control + ON/OFF

75-24V Modulating Control + Floating + ON/OFF

46-230V ON/OFF

05-44 lb-in. (5 Nm)

10-88 lb-in. (10 Nm)

A-Standard Model

1-No Feedback

2-Voltage Feedback Signal

0-No Internal Auxiliary Switches

2-Two Internal Auxiliary Switches

XX-System Controlled Numbers

CN75 10 A20 XX

BASIC FEATURES

Fig. 1. Setting units and control elements

Legend for Fig. 1:

1) Universal shaft adapter

2) Mechanical end limits (manually adjustable)

3) Declutch button

4) Function selection switch

5) Removable access cover

6) Anti-rotation bracket

Contents of Package

The delivery package includes the actuator, parts 1 through 6

(see Fig. 1), plus two cable grommets and a spare cable

grommet.

RUN MODES

The function selection switch (see Fig. 2) can be used to place

the actuator into any one of two different modes:

• Service/Off; or

• the floating/2-position run mode (“Dir” for CCW-closing

dampers or “Rev” for CW-closing dampers).

Fig. 2. Function selection switch

Power-Off Behavior

If power is removed, the shaft adapter remains in position.

Service/Off

If the function selection switch is set to the “Service/Off”

position, then all rotary movement is cancelled, and all

control signals are ignored, thus allowing the actuator to be

manually operated safely.

Model Description

CN6105A1011 5Nm, 24Vac/Vdc, floating control, non-spring

return, no feedback and without aux. Switch

CN4605A1001 5Nm, 230Vac, floating control, non-spring

return, no feedback and without aux. Switch

CN6110A1003 10Nm, 24Vac/Vdc, floating control, non-spring

return, no feedback and without aux. Switch

CN6110A1201 10Nm, 24Vac/Vdc, floating control, non-spring

return, no feedback and with aux. Switch

CN4610A1001 10Nm, 230Vac, floating control, non-spring

return, no feedback and without aux. Switch

N05

N10 SERIES DAMPER ACTUATORS FOR FLOATING/

-POSITON CONTROL

CN0B-0544CH33 R0805B

Floating/2-Position Run Mode

If the function selection switch has been set to one of the two

floating/2-position control settings—and if the actuator is wired

correspondingly (see Fig. 7, Fig. 8, and Fig. 9)—then as soon as

operating power is applied, the shaft adapter will run according to

the control signals applied.

Table 1 describes the behavior (“stops,” rotates “CCW,” or

rotates “CW”) of the CN6105/CN6110 in dependence upon the

control signals (switch “open” or “24 Vac/dc”) applied to terminals

3 and 4, the function selection switch setting, and the manner in

which the actuator is wired (either for floating mode: see Fig. 7;

or for 2-position mode: see Fig. 8).

Table 1. Behavior of CN6105/CN6110

wiring control signal at switch setting

term 3 term 4 Dir Service/ Off Rev

float. open open stops stops stops

open 24Vac/dc CCW stops CW

24Vac/dc open CW stops CCW

2-pos. 24Vac/dc open CW stops CCW

24Vac/dc 24Vac/dc CCW stops CW

Table 2 describes the behavior (“stops,” rotates “CCW,” or

rotates “CW”) of the CN4605/CN4610 in dependence upon the

control signals (switch “open” or “230 Vac”) applied to terminals 1

and 3 and the function selection switch setting: only one manner

of wiring is permitted (see Fig. 9).

Table 2. Behavior of CN4605/CN4610

control signal at switch setting

term 1 term 3 Dir Service/ Off Rev

open open stops stops stops

open 230 Vac stops stops stops

230 Vac open CW stops CCW

230 Vac 230 Vac CCW stops CW

MANUAL ADJUSTMENT

IMPORTANT

To prevent equipment damage, before manual

adjustment, you must remove power or set the func-

tion selection switch to the “Service/Off” position.

After removing power or setting the function selection switch to

the “Service/Off” position, the gear train can be disengaged using

the declutch button, permitting the shaft adapter to be manually

rotated to any position.

Limitation of Rotation Stroke

Two adjustable mechanical end limits are provided to limit the

angle of rotation as desired (see Fig. 3). The mechanical end

limits must be securely fastened in place.

Fig.3. Mechanical end limits

To ensure tight closing of the dampers, the shaft adapter has a

total rotation stroke of 95°.

INTERNAL END SWITCHES

The internal end switches “A” and “B” are changeover switches

which are activated when the shaft adapter moves past a position

of 5° and 85°, respectively (see also Table 5).

Fig.4. Internal end switch triggering points

CN0B-0544CH33 R0805B

N05,

N10 SERIES DAMPER ACTUATORS FOR FLOATING/

-POSITON CONTROL

INSTALLATION

To avoid personal injury (electrical shock) and to

prevent equipment damage, before installation, you

must remove power.

These actuators are designed for single-point mounting.

Mounting Instructions

All information and steps are included in the Installation

Instructions supplied with each actuator.

Mounting Position

The actuators can be mounted in any position (IP54 is dependent

upon orientation; see Fig. 5). Choose a mounting pKosition

permitting easy access to cables and controls.

Fig. 5. Mounting for IP54

NOTE: Further, in order to guarantee IP54, only original

Honeywell grommets may be used.

Anti-Rotation Bracket and Screws

If the actuator is to be mounted directly on a damper shaft, use

the anti-rotation bracket and screws included in the delivery

package. The min. distance between the center of the damper

shaft and the middle of the anti-rotation bracket is 3.35 in.; a

max. of 4.25 in. is allowed (see also Fig 11).

Depending upon the specifics of your mounting site, the actuator

may shift in position slightly while tightening the screws at the top

of the shaft adapter. The anti-rotation bracket features a T-piece

with a 5-mm-long shank to accommodate for this movement. It is

important to ensure that this play is not impeded.

Universal Shaft Adapter

The universal shaft adapter can be used for shafts of various

diameters and shapes (round: 3/8...5/8 in. and square:

1/4...1/2 in.).

WIRING

To avoid personal injury (electrical shock) and to

prevent equipment damage, before wiring, you

must remove power.

Access Cover

IMPORTANT

Once the access cover has been removed, please

take care to avoid damaging any of the parts now

accessible.

The access cover can be unscrewed and removed in order to

gain access to the terminal block(s) and perform wiring.

Fig. 6. Access Cover

Wiring Diagrams

Fig. 7. CN6105/CN6110 (floating mode)

CN0B-0544CH33 R0805B

N05

N10 SERIES DAMPER ACTUATORS FOR FLOATING/

-POSITON CONTROL

Fig. 8. CN6105/CN6110 (2-position mode)

CCW

230V~

230V ~

> 3 mm!

Fig. 9. CN4605/CN4610 (2-position mode)

Fig. 10. End switches

NOTE: Both internal end switches must be connected to the

same power source.

Tables 3,4 and 5 summarize the information presented in the

preceding wiring diagrams.

Table 3. Signals at terminals for CN6105/CN6110

ter-

minal signal in floating signal in 2-pos. mode

2 common ~/- common ~/-

3 24 V ~/+

(control signal) 24 V ~/+

(control/ power signal)

4 24 V ~/+

(control signal) 24 V ~/+

(control signal/power)

NOTE: All cables connected to these terminals must be

equipped with spark suppression.

Table 4. Signals at terminals for CN4605/CN4610

terminal signal

1 L (230 V ~)

2 N (230 V ~)

3 control signal

NOTE: All cables connected to these terminals must be

equipped with spark suppression.

Table 5. Internal end switches (SSW2)

terminal type of switch

S1 common lead for switches A and B

S2 / S3

change-over switch A (S1/S2 opens and

S1/S3 closes when shaft adapter moves CW

past 5°; reverts to original state when shaft

adapter moves CCW past 5°).

S5 / S6

change-over switch B (S1/S5 opens and

S1/S6 closes when shaft adapter moves CW

past 85°; reverts to original state when shaft

adapter moves CCW past 85°).

CN0B-0544CH33 R0805B

N05,

N10 SERIES DAMPER ACTUATORS FOR FLOATING/

-POSITON CONTROL

DIMENSIONS

Fig. 11. Dimensions (in in.)

Automation and Control Solutions

Honeywell International Inc. Honeywell (Tianjin) Limited

1985 Douglas Drive North 66, BaiHe Road, TEDA

Golden Valley, MN 55422 Tianjin, 300457,P.R.C.

Printed in China. on recycled

paper containing at least 10%

post-consumer paper fibers.

N05

N10 SERIES DAMPER ACTUATORS FOR FLOATING/

-POSITON CONTROL

CN0B-0544CH33 R0805B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell DCP301 Bedienungsanleitung

Honeywell

Honeywell HVC0002 Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Honeywell

Honeywell UltraKey Touch HJC4000 Bedienungsanleitung

Honeywell

Honeywell UDC3300 Bedienungsanleitung

Honeywell

Honeywell ML6275 Bedienungsanleitung

Honeywell

Honeywell ML6420A3072 Bedienungsanleitung

Honeywell

Honeywell VS820 POWERPILE Benutzerhandbuch

Honeywell

Honeywell Spyder PUL1012S Bedienungsanleitung

Honeywell

Honeywell Lyric Betriebsanleitung

Honeywell

Honeywell touchpoint Pro Bedienungsanleitung

Honeywell

Honeywell Sieger System 57 Bedienungsanleitung

Honeywell

Honeywell Pressuretrol L404 Series Bedienungsanleitung

Honeywell

Honeywell Lyric LCP300-LC Produktinformationsblatt

Honeywell

Honeywell B Bedienungsanleitung

Honeywell

Honeywell SUPER TRADELINE L4064B Bedienungsanleitung

Honeywell

Honeywell MN6105VAV Bedienungsanleitung

Honeywell

Honeywell HercuLine 10260A Bedienungsanleitung

Honeywell

Honeywell ML6421 Bedienungsanleitung

Honeywell

Honeywell EDC 200 Series Bedienungsanleitung

Honeywell

Honeywell V7335A 2000 Series Bedienungsanleitung

Honeywell

Honeywell Pro-Watch 7000 Bedienungsanleitung

Honeywell

Honeywell L7124U Bedienungsanleitung

Honeywell

Honeywell T775 Series 2000 Benutzerhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch