Honeywell DC1010 Bedienungsanleitung

DC1010/1020

1030/1040

Rev 4

Instruction Manual

(Input Conversion)

Contents

1. Input Change (TC & Linear  RTD) ......................................................................................3

2. Wiring Distinction between TC& Linear .....................................................................................4

3. Linear Input H/W Setting .........................................................................................................5

4. To view the ANL1, ANH1 parameters. .......................................................................................7

4-1. Unlock the protection.....................................................................................................7

4-2. Show the parameters.....................................................................................................7

4-3. Calibration ....................................................................................................................8

4-4. Procedure of Calibration.................................................................................................9

1. Input Change (TC & Linear  RTD)

To change the input type from TC to RTD or RTD to TC，Move a jumper.

For Linear type, it’s same as that of TC.

1) DC1010

2) DC1020/DC1030/1040

* No Calibration or Adjustment Required

While Input Conversion between TC & RTD.

RTD

2. Wiring Distinction between TC& Linear

1) DC1010

Set Input Code in Level 3

for TC or Linear Input after Profer Wiring

2) DC1030

Set Input Code in Level 3

for TC or Linear Input after Profer Wiring

3) DC1020/1040

Set Input Code in Level 3

for TC or Linear Input after Profer Wiring

Input Wiring

Linear

Input Wiring

Linear

Input Wiring

3. Linear Input H/W Setting

For jumper, please see ‘1. Input Changes’section.

1) DC1010

Input Type

Input Code

R1 to R5

S1 to S5

AN 4

AN 5

Jumper

Status

0~20 mA

R3 = 100 

R5 = 2.4 

S3 & S5

Short

4~20 mA

0~1 V

R1 = 2 K

R4 = 100 

S1 & S4

Short

0~5 V

1~5 V

R2 = 10 K

S2 & S4

Short

0~10 V

2~10 V

R3 = 22 K

S3 & S4

Short

0~100mV

20~100mV

S3 & S4

Short

2) DC1030

Input Type

Input Code

R1 to R5

S1 to S5

AN 4

AN 5

Jumper

Status

0~20 mA

R3 = 100 

R5 = 2.4 

S3 & S5

Short

4~20 mA

0~1 V

R1 = 2 K

R4 = 100 

S1 & S4

Short

0~5 V

1~5 V

R2 = 10 K

S2 & S4

Short

0~10 V

2~10 V

R3 = 22 K

S3 & S4

Short

0~100mV

20~100mV

S3 & S4

Short

3) DC1020/1040

Input Type

Input Code

R1 to R5

S1 to S5

AN 4

AN 5

Jumper

Status

0~20 mA

R3 = 100 

R5 = 2.4 

S3 & S5

Short

4~20 mA

0~1 V

R1 = 2 K

R4 = 100 

S1 & S4

Short

0~5 V

1~5 V

R2 = 10 K

S2 & S4

Short

0~10 V

2~10 V

R3 = 22 K

S3 & S4

Short

0~100mV

20~100mV

S3 & S4

Short

Input Type

Input Code

AN 1

AN 2

AN 3

AN 4

AN 5

-10~10mV

0~10mV

0~20mV

0~50mV

10~50mV

4. Calibration Procedure

Check if it shows the ANL1 and ANH1 on CONFIGURATION2. (Go to step 4-3.)

If the parameters are not shown, go to below steps.

4-1. Unlock the protection

Go to ‘LCK’ parameter on CONFIGURATION 1.

(1-1) Press the SET key for 5 seconds. It will show P1 on CONFIGURATION 1.

(1-2) Press the SET key until it will show LCK parameter.

(1-3) Input ‘1111’ to LCK parameter by using up/down and shift key.

(1-4) Press the SET and shift key for 5 seconds at ‘step (1-3)’. It shows ‘SET1’ of Step (2-1).

4-2. Show the parameters

Modify parameter of ‘CONFIGURATION 3’

(2-1) Press the SET key just one time until it will shows ‘SET2’.

(2-2) Change the first value of left side to 1. (SET2.2 = 1)

5seconds

Step (1-4)

Step (2-3)

5seconds

SET2.1

SET2.2

SET2.3

SET2.4

In case of RSP(Input2), SET2.4=1.(It shows ANL2, ANH2.)

(2-3) Press the SET and shift key for 5 seconds and return to OPERATION.

4-3. How to Calibrate

(3-1) Preparation of sources

- DC Current source : DC 0~20mA or 4~20mA

- DC voltage source : DC 0~1V, 0~5V, 0~10V, 1~5V, 2~10V

(3-2) Press the SET and shift key for 5 seconds, it will show ‘INP1’ of Configuration2.

Set INP1 to ‘AN5’ in case of DC 4~20mA.(Refer to INPUT CODE of ‘Linear input H/W setting’)

(3-3) Press the SET key just one time to show ANL1 parameter.

(3-4) Connect input source with INP1 terminals according to wiring diagram.

(3-5) Adjust the calibration values for Lower side(ANL1) and Upper side(ANH1).

In case of RSP(Input2), execute the calibration for each ANL2, ANH2.

(3-6) Refer to procedures as followings.

4-4. Procedure of Calibration

(Range of PV : 0~3000, Input : 4~20mA)

Set ‘INP1 = AN5’

‘SET 2.2 = 1’

(To activate the steps of ANL1 &

ANH1 )

Set INP1(Level 3), 4~20mA : AN5

(Refer to ‘3. Linear Input H/W

Setting’)

Define LSPL & USPL in Level 3

Assuming LSPL = 0, USPL = 3000

Input ‘Lower Limit signal’

In case of 4~20mA, input 4mA

Set ‘DP=0000’

DP : Decimal Point

Set Decimal point place

Go to ‘ANL1’ step in Level 3

Press ‘ ’ key, adjust ‘ANL1’

Adjust SP, until ‘PV=LSPL’

(In case of this, PV=0)

Press ‘ ’ key, adjust ‘ANH1’

Go to ‘ANH1’ step in Level 3

Input ‘Upper Limit signal’

In case of 4~20mA, input 20mA

Adjust SP, until ‘PV=USPL’

(In case of this, PV=3000)

Check, ‘OK’ ?

Check LSPL, USPL if right value

(Input Lower/Upper Limit signal, Check)

In case of Linear input model,

The default is ‘SET2.2 = 1’

END

Yes

Andere Handbücher für DC1010

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell LYNX Touch L5200 Series Bedienungsanleitung

Honeywell

Honeywell S8701 Bedienungsanleitung

Honeywell

Honeywell L7124U Bedienungsanleitung

Honeywell

Honeywell ML4195E Bedienungsanleitung

Honeywell

Honeywell HVC0001 Bedienungsanleitung

Honeywell

Honeywell UDC3500 Bedienungsanleitung

Honeywell

Honeywell TPPL Modbus TCP Montageanleitung

Honeywell

Honeywell S9360A Bedienungsanleitung

Honeywell

Honeywell Elster Jeavons J125 Bedienungsanleitung

Honeywell

Honeywell THR0924 Bedienungsanleitung

Honeywell

Honeywell UDC3300 Bedienungsanleitung

Honeywell

Honeywell DC1010 Kurzanleitung

Honeywell

Honeywell NOTIFIER NFXI-RM6 Bedienungsanleitung

Honeywell

Honeywell IAQ Poin Bedienungsanleitung

Honeywell

Honeywell V4055A Bedienungsanleitung

Honeywell

Honeywell MS4104F1010 Bedienungsanleitung

Honeywell

Honeywell RP920A Service-Handbuch

Honeywell

Honeywell P906C Bedienungsanleitung

Honeywell

Honeywell Spyder 5 WEB-RxxN Series Bedienungsanleitung

Honeywell

Honeywell ESYS S4965A3025 Bedienungs- und Montageanleitung

Honeywell

Honeywell KromSchroder IC 40 Handbuch

Honeywell

Honeywell V800 Bedienungsanleitung

Honeywell

Honeywell MP909E Datenblatt

Honeywell

Honeywell Centraline LION Installations- und Betriebshandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung