Honeywell Pro-Watch 7000 Bedienungsanleitung
Install Guide
Pro-Watch 7000
Intelligent Controller and System
PW7K1IC
Copyright© 2020 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their
respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this
document at any time without prior notice.
Pro-Watch® is a trademark of Honeywell, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at www.honeywellintegrated.com for information
about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at www.honey- wellintegrated.com to
post your comments.
Discover | Customer Portal
Self-Service Product Support and Learning Management System
https://honeywelldiscovertraining.com/login/discover/default.asp
YouTube | Honeywell Help and Support
https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured
PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 3
TABLE OF CONTENTS
Notices.......................................................................................................................................... 5
Warnings and Cautions......................................................................................................... 5
UL/ULC Warnings................................................................................................................... 6
CE + WEEE Marking................................................................................................................ 8
Damage During Shipment ................................................................................................... 9
Electro Static Discharge ....................................................................................................... 9
Disclaimer – Product Liability; Mutual Indemnification....................................... 10
Unpacking Procedure ......................................................................................................... 10
Shipping Instructions ......................................................................................................... 11
Limited Warranty .................................................................................................................. 11
Confidentiality ....................................................................................................................... 12
Compliance ............................................................................................................................. 12
Recommended testing and maintenance .................................................................. 12
Chapter 1 - ..................................................................... Product Overview13
PW-7000 and PW-6000........................................................................................................... 13
Port Settings.................................................................................................................................. 13
Other................................................................................................................................................. 15
Chapter 2 - Setting Up PW-7000 Hardware ............................................ 17
Setting the Jumpers................................................................................................................... 17
Setting the DIP Switches.......................................................................................................... 17
Bulk Erase Configuration Memory ................................................................................ 19
Bulk Erase ...................................................................................................................................... 19
Technical Specifications........................................................................................................... 20
Status LEDs................................................................................................................................... 20
Initialization ............................................................................................................................ 21
4 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1
Run Time Supplying Power to the PW-7000 Interface ..........................................22
Wiring ...............................................................................................................................................22
Supplying Power to the PW-7000 Interface .....................................................................23
Communications Wiring...........................................................................................................23
Cabinet Tamper and Power Failure Input Wiring............................................................24
Memory and Real Time Clock Backup Battery.................................................................25
Chapter 3 - System Configuration.............................................................. 27
Connecting to ACDSM for the First Time...........................................................................27
Login Page......................................................................................................................................28
Home Page .....................................................................................................................................28
Network Settings..........................................................................................................................28
Dynamic IP Configuration Method ................................................................................29
Static IP Configuration Method ......................................................................................30
Host Communication.................................................................................................................30
IP Server Connection Type ................................................................................................31
IP Client Connection Type .................................................................................................32
Device Information......................................................................................................................33
User Configuration......................................................................................................................33
Adding a User..........................................................................................................................34
Editing a User .........................................................................................................................35
Deleting a User.......................................................................................................................35
Restore Default Screen..............................................................................................................35
Apply Setting Screen ..................................................................................................................36
Log Out ............................................................................................................................................36
Chapter 4 - Reader Module........................................................................... 37
Reader Wiring .........................................................................................................................39
Input Wiring.............................................................................................................................39
Control Output Wiring.........................................................................................................40
PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 5
Notices
Wiring methods shall be in accordance with the National Electrical Code (ANSI/
NFPA70), Canadian Electrical Code, Part I (CSA C22.1) Safety Standard for Electri-
cal Installations, local codes, and the authorities having jurisdiction.
Warnings and Cautions
Note: See the Remote Enclosure Installation Manuals PW5K2ENC1/PW5K2ENC2 or
PW5K1ENC3 (not evaluated by UL) for installation instructions.
Before Installation
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply (see Technical Specifications beginning
on page 20).
Do not apply power to the system until after the installation has been completed.
Personal injury or death can occur, and the equipment can be damaged beyond
repair, if this precaution is not observed.
Fire Safety and Liability Notice (Not Evaluated by UL for fire, life safety, or burglary
application)
These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other
barrier. Use of egress buttons, for example, may be illegal in some cities. In most
Caution: Disconnect power before servicing.
Caution: ATTENTION: Débranchez l'alimentation électrique avant
l'entretien.
Warning: Before installation, TURN OFF the external circuit breaker
which supplies power to the system.
Warning: AVERTISSEMENT: Avant de procéder à l'installation,
DESENCLENCHER le disjoncteur via lequel le système est
alimenté.
Warning: Never connect card readers to any critical entry, exit door,
barrier, elevator or gate without providing an alternative exit in
accordance with all the fire and life safety codes pertinent to
the installation.
Warning: AVERTISSEMENT: Ne jamais connecter de lecteur de carte en
un point critique (porte de sortie, barrière, ascenseur ou
portillon) sans proposer une autre sortie, ce afin de respecter la
règlementation en vigueur en matière d'incendie et de
protection des vies humaines, afférente à l'installation.
6 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1
applications, single action exit without prior knowledge of what to do is a life safety
requirement. Always make certain that any required approvals are obtained in writ-
ing. DO NOT ACCEPT VERBAL APPROVALS SINCE THEY ARE NOT VALID.
Honeywell Integrated Security never recommends using the PW-7000 or related
products for use as a primary warning or monitoring system. Primary warning or
monitoring systems should always meet the local fire and safety code require-
ments.
Failure to test a system regularly could make the installer liable for damages to the
end user if a problem occurs.
Earth Grounding
Use Suppressors
UL/ULC Warnings
The following applies to installations that require UL or ULC compliance:
Only UL/ULC Listed readers with standard Wiegand data output communication
format (protocol) have been evaluated for use with this system.
This product is intended to be installed indoors, within the protected premises.
Access Control System, Model PW7000, and Controller, Model PW7K1IC meet the
requirements for CAN/ULC-S319-05 Equipment Class 1. This product's compli-
ance to ULC-S319, Electronic Access Control Systems, will be considered invali-
dated through the use of any add-on, expansion, memory or other module
manufactured or supplied by the manufacturer or manufacturer's representative,
unless specifically evaluated by ULC.
All unused conduit holes must be properly plated or incorporate a Listed plug to fill
any voids.
All interconnecting devices must be UL/ULC Listed.
Shielded cable shall be employed for all Input/Output wiring.
Warning: The earth ground is connected at the factory and should not be
removed.
Warning: AVERTISSEMENT: La prise de terre est reliée à l'usine et ne doit
pas être retirée
Warning: Use suppressors on all door strikes. Use S-4 suppressors for
installation. Honeywell Integrated Security, Inc. recommends
only DC strikes.
Warning: AVERTISSEMENT: Employer des suppresseurs de surtensions
transitoires (S-4) sur toutes les gâches de porte. Honeywell
Integrated Security recommande l'utilisation exclusive de
gâches électriques à courant continu.
PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 7
Refer to the following Installation manuals for installation, connection, program-
ming, and operation instructions of the following sub-assemblies:
Note: Not Evaluated by UL for fire, life safety, or burglary applications.
Note: The earth ground is connected at the factory and should not be removed.
Do Not Connect To A Receptacle Controlled By A Switch.
Replacement 3 volt lithium coin cell must be one of the following:
Rayovac: BR2325 or BR2335-B
All interconnecting wire must be UL/ULC Listed, rated and suitable for the use.
The battery leads and primary AC main power wiring is non-power limited. This wir-
ing must be separated from all other wiring by at least 0.25" and cannot be
installed in the same conduit as any other power limited wiring.
The system must be configured to activate an alarm or trouble signal. Failure to do
so will not allow the access function to operate in the event of a tamper.
Note: The following applies to installations that require UL or ULC compliance:
• Only UL/ULC Listed readers with standard Wiegand data output
communication format (protocol) have been evaluated for use with this system.
• This product is intended to be installed indoors, within the protected premises.
• Access Control System, Model PRO4200, and Controller, Model PRO42IC meet
the requirements for CAN/ULC-S319-05 Equipment Class 1.
• This product's compliance to ULC-S319, Electronic Access Control Systems, will
be considered invalidated through the use of any add-on, expansion, memory or
other module manufactured or supplied by the manufacturer or manufacturer's
representative, unless specifically evaluated by ULC.
• All unused conduit holes must be properly plated or incorporate a Listed plug to
fill any voids.
Assembly Number Installation Manual Part Number
PW7K1IC 800-25673
PW7K1R2 800-25676
PW7K1IN 800-25674
PW7KOUT 800-25675
PW6K1IC 800-00005V3
PW6K1R2 800-01951V4
PW6K1IN 800-01952V1
PW6K1OUT 800-01953V1
PW5K2ENC1 and PW5K2ENC2 800-06952
PW5K1ENC3 800-06955V1
PW5K2ENC5 800-08421
PW6K2E2PS 800-08279V3
8 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1
Note: Total current draw for all included assemblies shall not exceed 4A, including input
rating and output load current.
• Suitable for S319, Class I
• Suitable for the following UL293/UL294 Performance Levels:
• Endurance: IV
• Standby: I
• Line Security: I
• Attack: I
• Suitable panic or exit hardware shall be employed for fail secure applications.
For UL293 applications, the Sys Fault contacts of the power supply and the door
held, door forced shall be monitored by suitable audible device.
CE + WEEE Marking
Description of the used symbol.
CE -Standard -Logo. This product complies with
the harmonized Regulation of the EU
WEEE symbol.It indicates this product is to be
recycling and not been thrown in the dustbin
PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 9
Damage During Shipment
Electro Static Discharge
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
installation and user guides, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
Note: This document and the data in it shall not be duplicated, used or disclosed to others
for procurement or manufacturing, except as authorized by and with the written
permission of Honeywell Integrated Security, Inc. The information contained in this
document or in the product itself is the exclusive property and trade secrets of
Honeywell Integrated Security, Inc. Copyright laws of the United States protect all
information in this document or in the software product itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell
Integrated Security, Inc. Software Agreement. Please request a copy from Honeywell
Integrated Security, Inc. (http://www.honeywellintegrated.com/index.html), and
review the agreement carefully.
Caution: IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM
MUST BE FILED WITH THE COMMERCIAL CARRIER
RESPONSIBLE FOR THE DAMAGE.
Caution: ATTENTION: SI L'EQUIPEMENT A SUBI DES DOMMAGES LORS
DE SON TRANSPORT, ADRESSER UNE RECLAMATION AU
TRANSPORTEUR RESPONSABLE.
Caution: Electro-static discharge (ESD) can damage CMOS integrated
circuits and modules. To prevent damage always follow these
procedures:
• Use static shield packaging and containers to transport all electronic
components, including completed reader assemblies.
• Handle all ESD sensitive components at an approved static-
controlled workstation. These workstations consist of a desk mat,
floor mat and an ESD wrist strap. Workstations are available from
various vendors.
Caution: ATTENTION: Des décharges électrostatiques peuvent
endommager les modules et circuits intégrés CMOS.
10 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1
Disclaimer – Product Liability; Mutual Indemnification
If a Customer receives a claim that a Product or any component thereof has caused
personal injury or damage to the property of others, Customer shall immediately
notify Honeywell Integrated Security in writing of all such claims. Honeywell Inte-
grated Security shall defend or settle such claims and shall indemnify and hold
Customer harmless for any costs or damages including reasonable attorneys’ fees
which Customer may be required to pay as a result of the defective Product or the
negligence of Honeywell Integrated Security, its agents, or its employees.
Customer shall hold harmless and indemnify Honeywell Integrated Security from
and against all claims, demands, losses and liability arising out of damage to prop-
erty or injury to persons occasioned by or in connection with the acts or omissions
of Customer and its agents and employees, and from and against all claims,
demands, losses and liability for costs of fees, including reasonable attorneys’ fees,
in connection therewith.
Unpacking Procedure
All containers should be opened and unpacked carefully in order to prevent dam-
age to the contents.
Follow these steps to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all the packing materials. They may be used again for reshipment
of the equipment, if needed.
2. Inspect the contents to see if anything is missing. If you notice any missing
items, contact the order entry department at 1-800-323-4576 Option-1.
3. Visually check the contents. If you see any damage, do the following:
a. If shipping has caused damage to the unit, a claim must be filed with the
commercial carrier.
b. If any other defect is apparent, call for a return authorization.
Caution: If any damage to the shipment is noticed before unpacking, a
claim must be filed with the commercial carrier.
Caution: ATTENTION: SI L'EQUIPEMENT A SUBI DES DOMMAGES LORS
DE SON TRANSPORT, ADRESSER UNE RECLAMATION AU
TRANSPORTEUR RESPONSABLE.
Andere Handbücher für Pro-Watch 7000
4
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Honeywell Controller Handbücher
Honeywell
Honeywell CUL6438SR-CV1 Bedienungsanleitung
Honeywell
Honeywell UDC 2300 Bedienungsanleitung
Honeywell
Honeywell DC1000 SERIES Bedienungsanleitung
Honeywell
Honeywell ML6161E Bedienungsanleitung
Honeywell
Honeywell HR 10 F Bedienungsanleitung
Honeywell
Honeywell CentraLine LYNX BACnet CLLYUB1012S Bedienungsanleitung
Honeywell
Honeywell MO953 Series Montageanleitung
Honeywell
Honeywell CP-UL1012S Bedienungsanleitung
Honeywell
Honeywell HCE80 Betriebsanleitung
Honeywell
Honeywell UDC2500 Bedienungsanleitung
Honeywell
Honeywell MT4-024 Bedienungsanleitung
Honeywell
Honeywell L7224A Bedienungsanleitung
Honeywell
Honeywell CENTRA LINE MERLIN NX Series Bedienungsanleitung
Honeywell
Honeywell Electronic Aquastat L7148F Bedienungsanleitung
Honeywell
Honeywell SEC-H-602 Bedienungsanleitung
Honeywell
Honeywell CENTRALINE EAGLE Bedienungsanleitung
Honeywell
Honeywell HCE80R Bedienungsanleitung
Honeywell
Honeywell HW-AV-LTE-M Bedienungsanleitung
Honeywell
Honeywell MIWI350 Betriebsanleitung
Honeywell
Honeywell HJK7000 UltraKey Plus Bedienungsanleitung
