Honeywell NEXH Bedienungsanleitung

- 1 -

ENG

INSTALLATION GUIDE BOOK

NEXH Camera

Explosion proof Security Camera

(FIXED HD IPType)

- 2 -

Important Safety Instructions

ENG

1. Install and use this system after reading these instruction thoroughly.

2. Keep these instructions.

3. Install in accordance with the manufacture’s instruction.

4. Take care of all Cautions and Warnings.

5. Use stainless steel hardware to fasten the mount to outdoor surfaces.

6. Only use replacement parts recommended by the manufacturer.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER(OR BACK).

NO USER SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PRERSONNEL

Explanationof Graphical Symbols.

This symbol is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient

magnitudeto constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important

operating and maintenance(Servicing)Instructions in the literature

accompanyingthe appliance.

TO REDUCE THE RISK OF IGNITION DO NOT OPEN WHEN AN EXPLOSIVE

GAS ATMOSPHERE MAY BE PRESENT

WARNING: To reduce the risk of ignition of hazardousatmospheres,conduit runs

must have a sealing fitting or cable gland connected within PT 3/4 inches of the

enclosure.

WARNING: To reduce the risk of ignition of Hazardous Atmospheres,

disconnectthe equipment from the supply circuit beforeopening.

- 3 -

Methods of Installation

Figure1.

Method of Installation

ENG

CameraHousing

only with Bracket

This system can be installed in a standard or inverted position or camera Housing only with

optionalbracket as below Figure1.

Wheninstalled for inverted operation,the origin of camera shall be reconfigured through the

Camera function.There is no need to be adjusted physically but sunshield bracket may not

be functionalat this case.

WARNING: Gross weight of this system is about 15kg. Use caution when lifting

and installing. It is recommended you to wear proper non-slip gloves be worn during

installation.

- 4 -

Install on the surface or on the wall with Mount bracket

To install this product, please refer to Figure2 and do the following steps.

1. Make sure the threads of the product and the threads of the supplied stainless steel bolts (Supplied) are

freeof dirt and debris.

2. Apply an amount of threadlocking compound(notsupplied) to the thread of the product and the thread of

the bolts.

3. Secure the product to the mountingsurface with the adjusted wrench and four stainless steel bolts and lock

washers. Tightenthe bolts to 150~300 kgf.cm(14Nm~29Nm)

Figure2.

Note : Figure2 shows the product being installed on a wall mount bracket which is an optional

product; NEXH-WL (not supplied) and if there is no need the wall mount bracket, just follow a

above step to install the product without wall mount bracket.

Methods of Installation

ENG

- 5 -

Methods of Installation

Figure3

Install Product to Mounting surface

PT 3/4 “-14

Seal Fitting

(Not Supplied)

Explosion proof

Flexible conduit

(Not Supplied)

PT 3/4”-14 Nipple

Fiber

Filler

Sealing

compou

Cables

Sealing Method

PT 3/4”-14 Thread

To install this product, please refer to Figure3 and do the following steps.

1. Make sure the threads of the supplied three M10X30mm stainless steel bolts and flat/springwashers are free

of dirt and debris.

2. Apply an amount of threadlocking compound(notsupplied) to the thread of the product and the thread of the

bolts.

3. Make sure the seal fittings(notsupplied) and the threaded hole of this system are free of the dirt and particles.

4. Assemble nipple,the threaded hole of this system, seal fittingand flexibleconduit(notsupplied) to be fasten

firmlyand then the cables must be passed through the seal fitting,Nipple and flexibleconduit.

Plus, the sealing fitting,flexibleconduit, Nipple should be acquired ATEX/IECEx Certification.

Note : Figure3 shows the product being installed on a surface with pedestalmount.

ENG

- 6 -

Figure5.

Base Schematic of Installation

1. Figure5is recommendedfor the base Schematicof Installation.

2. If you wish to consist of another method or other components, you must proceed to do after

conferringwith a manufacture.

Base Schematic

ENG

Power

POWER

AC110 or 220V

BNC

MAIN MONITOR

DATA1 DATA2

+ - -+ + -

REAR

FRONT

KEYBOARD CONTROLLER

HTX-5000

REAR

DATA 2 D ATA1 DC 12V

RS 485

1 DOME 2

IN OUT DVR RS 232C

ALARM/DVR

DC 12V

SLAVE

RS 485 +

Pump-

Pump+

RS 485

DVR

Check Valve

Pump

Motor

Input Power DC 12~24V

GND

LAN

Local Network

External Network

Monitoring PC

Router

Monitoring PC

Internet

Intranet

- 7 -

Configuration of Wire Harness

Figure4

Cable configuration

Cable Configuration

ENG

2m ±0.3m

Wire Color Function Description

Brown

Sky Blue

Green

Power Input

(AC 110V ~ 230V)

GND

LAN Cable Video & Network UTP

Power

LAN Cable

Configuration of Wire Harness

- 8 -

ENG

Key Feature and Introduction

The network camera supports the network service for a sensor image with progressive scan,

which can be monitored on a real-time screen regardless of distances and locations. By using its

dedicatedprogram, many users are able to have an access to the network camera at once or a

single user can monitor various network cameras at the same time. It also enables users to play,

store and retrieve a monitoring image by using a PC. All the settings and real-time monitoring

screens are also provided through an access to the web.

The network camera is fully featuredfor security surveillance and remote monitoring needs. It is

based on the DSP compression chip, and makes it available on the network as real-time, full

framerate Motion JPEG and H.264 video streams

The Highest level Ex Class : Ex d IIC T6 (IECEx, ATEX, CE, FCC, KC)

Corrosion resistant SUS 316 Construction

IP67 Protection

Built-in Wiperfunction

Integratedwith Waterjet : EXWJ400

Approx 15Kg of light weight

- 9 -

Key Feature and Introduction

•Brilliant video quality

The network camera offersthe highly efficientH.264 video compression, which drastically

reduces bandwidth and storage requirementswithout compromising image quality. Motion JPEG

is also supported for increased flexibility.

• Dual or Triple Streams

The network camera can deliver dual or triple video streams simultaneously at full frame rate in

all resolutions up to Full-HD (1920 x 1080p) using Motion H.264 and JPEG. This means that

several video streams can be configuredwith differentcompression formats, resolutions and

framerates for differentneeds.

• Image setting adjustment

The network camera also enables users to adjust image settings such as contrast, brightness

and saturation to improve images beforeencoding takes place.

• Intelligent video capabilities

The network camera includes intelligent capabilities such as VCA (Video Content Analysis). The

network camera’s external inputs and outputs can be connected to devices such as sensors and

relays, enabling the system to react to alarms and activate lights or open/close doors.

• Improved Security

The network camera logs all user access, and lists currently connectedusers. Also, its full frame

rate video can be provided over HTTPS.

• ONVIF Certificate

This is a global interface standard that makes it easier for end users, integrators, consultants,

and manufacturersto take advantageof the possibilities offeredby network video technology.

ONVIF enables interoperability between differentvendor products, increased flexibility, reduced

cost, and future-proofsystems.

• Micro-SD Recording support

The network camera also supports a Micro-SD memory slot forlocal recording with removable

storage.

• Audio support

The network camera also supports two-way audio.

ENG

- 10 -

Specifications

General Mechanical & Electrical

Models

Spec

NEXH3020HD-NET

Signal System

RJ45 (10/100 Base-T)

Ex. Class

Ex d IIC T6

Certifications

IECEx, ATEX, CE, FCC, KC

Front window

Fully tempered plate glass

Material

SUS 316

Protection Degree

IP 67

Input Voltage

100-230 V~, 50/60Hz

Power consumption

Max15W

Operating Temperature

-20°C ~ 60°C

Weight

Approx. 15 kg

ENG

Inhaltsverzeichnis

Andere Honeywell Digitalkamera Handbücher

Honeywell

Honeywell HPXD2 Bedienungsanleitung

Honeywell

Honeywell ExitView Bedienungs- und Wartungsanleitung

Honeywell

Honeywell HCC-745NTW/PTW Bedienungsanleitung

Honeywell

Honeywell Pentax Spotmatic IIa Bedienungsanleitung

Honeywell

Honeywell HD-SDC-3300P Bedienungsanleitung

Honeywell

Honeywell 2450Cm Series Bedienungsanleitung

Honeywell

Honeywell Pentax Spotmatic Bedienungsanleitung

Honeywell

Honeywell PERFORMANCE LITE 2MP SD Bedienungsanleitung

Honeywell

Honeywell 2450Cm Series Bedienungsanleitung

Honeywell

Honeywell VENTI Series Bedienungsanleitung

Honeywell

Honeywell NEXH Series Produkthandbuch

Honeywell

Honeywell Color Camera Bedienungsanleitung

Honeywell

Honeywell Pentax Spotmatic Bedienungsanleitung

Honeywell

Honeywell Spotmatic Iia Bedienungsanleitung

Honeywell

Honeywell 2450Cm Series Bedienungsanleitung

Honeywell

Honeywell Pentax Spotmatic II Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung