Honeywell POWER PRESENTER RF Bedienungsanleitung

POWER PRESENTER RF

Instruction Manual

The POWER PRESENTER RF remote is a handy, compact presentation tool. It allows you to control slides

in any presentation or slide show software. The Power Presenter RF remote includes a built in laser pointer.

The kit includes: a remote with laser pointer (battery included), a receiver, a USB cable and a nylon

carrying case. The POWER PRESENTER RF uses radio frequency technology, so you don’t have to point

the remote at the receiver to control your slides. The maximum operating distance between the remote and

the receiver is 150 feet, depending upon operating environment.

System Requirements

The only system requirement is USB compatibility. The POWER PRESENTER RF is “plug and play”

compatible with MAC OS 8 or higher and Windows 98, NT, 2000, XP or higher.

Connecting the Receiver to the Computer

For maximum range, the receiver should be placed as far away as possible from any electronic devices.

Using a USB connection (MAC OS 8 or higher and Windows 98, NT, 2000 or higher)

1) Turn on your computer and let it fully boot-up.

2) Plug Type-A end of the USB cable into the USB port on your computer.

3) Plug Type-B end of the USB cable into the USB port on the receiver.

Note: The Type-A USB port on the receiver is used for connecting additional USB devices

To your computer through your Power Presenter receiver unit.

4) The computer should automatically recognize the receiver as a new

hardware after about 5 to 15 seconds, depending on the computer.

Follow the instructions for installing new hardware (you may need to

load the necessary USB driver from your operating system disk). Once

your computer has installed the receiver as new hardware it will not need

to run through the same steps again. Next time you plug the receiver into

the same computer, it will take about 5 to 10 seconds to recognize the receiver. During the 5 to 10 seconds

there may be little or no indication that the computer is communicating with the receiver.

Connecting Another USB Device

The USB Type-A, female port (rectangular shaped Usb female connector) on your POWER PRESENTER

RF receiver is connected to an internal USB hub port. This port will allow you to connect other USB

devices to your computer through your POWER PRESENTER RF receiver unit. To use this port, simply

connect a USB device with a Type-A, connector into the port.

Note:USB 2.0 devices will work at USB 1.1 speeds when connected to this port as the POWER

PRESENTER RF is a USB 1.1 compatible device.

Part # PPRF

Training the Remote to the Receiver

The remote has been trained into the receiver at the factory. The receiver can support up to 7 total remotes.

To train a new remote, or re-train an existing remote, into the receiver:

1) Press and release the program button on the receiver (the LED lights solid).

2) Press the advance button (the largest button) on the remote three times. On the third press, the LED will

turn off, indicating the remote has been successfully trained.

To delete all of the remotes from the receiver:

1) Press and hold the program button. The LED will light for 3 seconds then go out.

2) Release the program button.

Using the Remote

After connecting the receiver properly, simply start

your presentation or slide show software, put it in

slide show mode, and press the larger advance button

to advance the slides and the smaller reverse button to

go back to the previous slide. The advance button

mimics the page down button on the keyboard and the

reverse button mimics the page up button.

Press the smallest button to activate the laser pointer.

Changing the Remote Keystrokes

1) Turn on your computer and let it fully boot-up.

2) Plug the USB cable into the back of your computer.

3) Plug the other end of the USB port on the receiver.

4) Launch a text editing software application (i.e. word)

5) Open a blank document and display it on the front window of your monitor.

6) On the back of the Base/Receiver, press the Program Button three (3) times.

7) Keyboard commands will begin appearing on your open text window. When the command required for

your software appears, press the button on your remote that you wish to match to that keystroke.

a) For Power Point the normal commands are;

•Page Down- Top Button

•Page Up – Middle Button

•b (blank screen) – Top and Middle Buttons pressed together

b) For Media Shout the normal commands are;

•F10 – Top Button

•F9 – Middle Button

•F6 (blank screen) – Top and Middle Buttons pressed together

8) When a command is recognized, the LED on the Base/Receiver will flash and the scrolling text will

pause. The scrolling will continue until all three button command options (top, middle, both) are

programmed.

9) If you do not wish to use all three keystroke commands, simply unplug your Base/Receiver from the

cable to stop the process.

10) Close your text editing software application.

11) Test your remote to confirm the commands you have selected.

Changing the Battery in the Remote

1) There are two “alignment dots” on the back of the remote

case and one “alignment dot” on the battery cover. Insert a

quarter into the slot on the battery cover and turn counter

clockwise until the dot on the battery cover is lined up with

the LEFT dot on the remote case. The battery cover will release.

2) Pull the battery out of the holder. Dispose of the battery in

an environmentally proper manner.

3) Insert the new battery with the positive side facing you. The

lithium 3.0 volt battery number is CR2032.

4) Make sure that the “alignment dot” on the battery cover is lined

up with the LEFT “alignment dot” on the remote case as you replace

the battery cover. Then turn clockwise until the dot on the battery

It is recommended that you always carry a spare battery.

Product Specifications

Transmitter:

• Range: Up to 150 feet, depending upon operating environment

• Dimension: 2.6” (66mm)L x 1.5”(38mm)W x 0.5”(13mm)H

• Weight: 1 oz (24 g) with batteries

• Radio Frequency: 433 MHz

• Laser: Diode Laser, 5mW max output at 650NM, Class IIIa

• Power: CR2032 battery

• Battery life: 1 year under normal operation

Receiver:

• Interface: USB port

• Dimensions: 2.6”(66mm)L x 3.4” (86mm)W x 1.2” (31mm)H

• Weight: 2 oz (59g) excluding cable

Cables:

• 3ft USB cable (A/B)

General:

• Warranty: 1 year, limited

• Compliance: FCC part 15; Class B for U.S., Industry Canada RSS-210,

FDA 21 CFR 1040

Laser Pointer Information

Due to the potential of radiation exposure from the laser, the Food and Drug

Administration (FDA) requires that any user of this product report and return

a defective unit to the manufacturer. DO NOT point the laser light directly into

the eye area or attempt to open or disassemble this product for any reason.

Tampering with the laser product may be hazardous and will automatically

VOID the manufacturer’s warranty.

This product fully complies with FDA 21 CFR 1040.10 and 1040.11.

Troubleshooting

“I’m pressing the advance button but the slides are not advancing.”

1) Check the cable connections.

2) Verify that the LED on the remote comes on solid when the advance or reverse button is pushed and that

the laser pointer is at full brightness when the laser button is pushed. If not, replace the battery.

3) Verify that the transmitter has been trained to the receiver. Follow the instructions under “Training the

Remote to “the Receiver”.

4) If using USB, verify that the correct operating system driver is loaded on your computer. Try reloading

the driver, or try unplugging the receiver, waiting 10 seconds, and then plugging it back in.

“The LED on the remote flashes or does not turn on when I push the advance or reverse button, or

the laser pointer is dim or does not work when the laser button is pushed.”

1) The battery is dead. Replace the battery.

Limited Warranty

Street Smart Technologies, a Division of Honeywell Home and Building Control, (“Seller”), 13475

Danielson St. Suite#120, Poway California 92064, warrants its product to be in conformance with its own

plans and specifications and to be free from defects in material and workmanship under normal use and

service for 12 months from the date of original purchase.

Seller’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or

labor, any product that is proved not in compliance with Seller’s specifications or proves defective in

materials or workmanship under normal use and service. Seller shall have no obligation under this Limited

Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than

Street Smart Technologies. When returning a product, a Return Material Authorization number (RMA#) is

required and must be obtained from Street Smart Technologies. The RMA# must be clearly displayed on

the outside of the shipping carton and the product must be accompanied by documentation that explains the

problem and provides proof of date of purchase.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interferences that may cause undesired operation.

FCC ID: Transmitter: KFR-LSRTS Receiver: KRF-LSRRS

Federal Communications Commission (FCC) Statement

This equipment has been tested to FCC requirements and has been found acceptable for use.

The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in

strict accordance with the manufacturer’s instructions, may cause interference to radio and television

reception. It has been type tested and found to comply with the limits for a Class B computing device in

accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause interferences to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Reorient the receiving antenna until interference is reduced or eliminated

• Move the receiver away from the control/communicator.

• Move the antenna leads away from any wire runs to the control/communicator.

• Plug the control/communicator into a different outlet so that it and the receiver are on different branch

circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for

additional suggestions. The user or installer may find the following booklets prepared by the Federal

Communications Commission helpful:

“Interference Handbook” This booklet is available from the U.S. Government Printing Office, Washington,

DC 20402. The user shall not make any changes or modifications to the equipment unless authorized by the

installation instructions or User’s Manual. Unauthorized changes or modifications could void the user’s

authority to operate the equipment.

Honeywell

13475 Danielson St. Suite#120

Poway, CA 92064

(858) 513-6391

www.powerremote.com

Inhaltsverzeichnis

Andere Honeywell Digitaler Präsentator Handbücher

Honeywell

Honeywell POWER PRESENTER PLUS 64/128 Bedienungsanleitung

Beliebte Digitaler Präsentator Handbücher anderer Marken

Edirol

Edirol RG-100 Bedienungsanleitung

Hama

Hama Como Bedienungsanleitung

Dukane

Dukane AV-P1000 Bedienungsanleitung

Canon

Canon PR3 Bedienungsanleitung

VSON

VSON N81 Bedienungsanleitung

Samsung

Samsung UF-130DX Bedienungsanleitung

Targus

Targus Multimedia Bedienungsanleitung

Edirol

Edirol PR-50 Betriebsanleitung

x-pointer

x-pointer IMAGE POINTER XPM170Y Bedienungsanleitung

Acrobak

Acrobak BLP-305 Bedienungsanleitung

Targus

Targus Mac AMP11 Bedienungsanleitung

Edirol

Edirol PR-50 Bedienungsanleitung

Samsung

Samsung SDP-850 Bedienungsanleitung

Dukane

Dukane DV-P303A Bedienungsanleitung

RemotePoint

RemotePoint Presenter Global Bedienungsanleitung

Kensington

Kensington Wireless Presenter with Laser Pointer Betriebsanleitung

NEC

NEC DS1-MP10RX2 Betriebsanleitung

Logitech

Logitech R800 - Professional Presenter Presentation Remote... Bedienungsanleitung