Honeywell FIRE-LITE ALARMS SLC-3LS Technisches Handbuch

One Fire-Lite Place

Northford, CT 06472-1653 USA

203-484-7161 • FAX 203-484-7118

www.firelite.com

SLC-3LS Loop Expander Module

Product Installation Document

PN LS10195-000FL-E:A 6/7/2023 ECN: 00022081

1 Description

The SLC-3LS Loop Expander Module is an optional card that provides the ES-1000X Series Fire Alarm Control Panels with additional SLC commu-

nication loops. An additional 318 devices can be wired to each SLC-3LS card. A maximum of two SLC3-LS cards may be installed on the FACP,

offering a total of 3 SLC loops and 954 points in the system.

2 Installation

The IPOTS-COM Communicator Module, not supplied with the ES-1000XI, must be mounted on the FACP last, at the top of the stack of accessory

cards. Additional SLC-3LS cards mount below the IPOTS-COM Communicator. Refer to P/N LS10184-000GE-E for instructions on installing the

IPOTS-COM Communicator, if necessary.

Refer to Figure 1 and Figure 2 below.

1. Disconnect the ribbon cable from J1 on the IPOTS-COM.

2. Remove the four screws on the right side of the board that are used to attach the IPOTS-COM board to the chassis (or, on the ES-1000XI, to the

PCB itself) and place it on static-safe workspace.

3. Disconnect and remove the 8” (20 cm) wire cable from J4 on the pre-installed SLC-3LS card and J5 on the main board.

WARNING: STATIC SENSITIVE COMPONENTS

WEAR A PROPER GROUNDING WRIST STRAP AND WORK ON A STATIC-SAFE WORKSPACE TO PROTECT

ELECTRONIC ASSEMBLIES.

Remove screws

pre-installed

SLC-3LS card

IPOTS-COM

Remove 8” (20cm) cable

Disconnect ribbon cable

Figure 1 ES-1000X Assembly

2SLC-3LS Installation Document — P/N LS10195-000FL-E:A 6/7/2023

4. Install the 4” (10 cm) wire cable from the kit into J5 on the main board.

5. Install the new SLC-3LS card onto the standoffs.

6. Connect the 4” (10 cm) wire cable from step 4 into J4 (upper position) on the new SLC-3LS.

7. Connect the 8” (20 cm) cable removed in step 3 to J3 (lower position) on the new SLC-3LS and J4 (upper position) on the pre-installed SLC-3LS.

8. Install the four standoffs from the kit into the new SLC-3LS.

9. Align the IPOTS-COM over the standoffs and secure with the screws removed in step 2.

10. Reconnect the ribbon cable into J1 of the IPOTS-COM.

11. If a third loop expander module is required in the system, mount it below the IPOTS-COM using the 4” (10 cm) cables to connect the loop cards

on the right and the 8” (20 cm) cable to the pre-installed loop card on the left.

pre-installed

SLC-3LS card

Replace with 4” (10 cm) cable

from kit of new SLC-3LS

Figure 2 ES-1000X Assembly

align over standoffs and

add new standoffs

align over standoffs

and add new standoffs

Install 8” (20 cm) cable

to J4 on pre-installed

SLC-3LS card

Install 4” (10 cm) cable

to FACP connector J5

Figure 3 New SLC-3LS Card

J4 IN

J3 OUT

SLC-3LS Installation Document — P/N LS10195-000FL-E:A 6/7/2023 3

3 Wiring/Configuring the SLC-3LS

Connect the SLC wiring and devices to the terminal block on the SLC Expander Module. SLC loops can be wired as Class A, Class B, or

Class X (DCLA, DCLB, or DCLC for Canadian applications).All SLC connections are supervised and power-limited. Refer to the SLC Wiring

Manual #51309 for wiring information.

There are three switches on the SLC-3LS.

• Ground fault disable: disable ground fault detection for troubleshooting purposes only.

• SLC address: 16 position switch for addressing the loop card only. Note that “0” is not a valid address.

• RS-485 termination: enable/disable this switch for the last loop card installed for better functionality.

SLC

Out

Optional Class A (DCLA)

return wiring

ground fault disable

SLC address

RS-485 termination

+ + - -

Figure 4 SLC-3LS Switches

Inhaltsverzeichnis

Andere Honeywell Extender Handbücher

Honeywell

Honeywell CBU146 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4208U Montageanleitung

Honeywell

Honeywell WREX Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4229 Bedienungsanleitung

Honeywell

Honeywell PIT Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4297 Montageanleitung

Honeywell

Honeywell INTEVIO RK-ZONE8 Merkblatt

Honeywell

Honeywell 4219 Bedienungsanleitung

Honeywell

Honeywell HPF602ULADA Bedienungsanleitung

Honeywell

Honeywell HPFF8 Bedienungsanleitung

Honeywell

Honeywell IB2 Gebrauchsanweisung

Honeywell

Honeywell 6815 Technisches Handbuch

Honeywell

Honeywell Silent Knight EVS-CE4 Technisches Handbuch

Honeywell

Honeywell 6815 Technisches Handbuch

Honeywell

Honeywell HPFF12 Bedienungsanleitung

Honeywell

Honeywell IB2 Gebrauchsanweisung

Honeywell

Honeywell HPFF12 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER PSE-6 Bedienungsanleitung

Honeywell

Honeywell 4219 - Ademco 8 Zone Expander Montageanleitung

Honeywell

Honeywell Farenhyt ECS-CE4 Technisches Handbuch

Honeywell

Honeywell HPF902ULADA Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung