Honeywell NS1 Bedienungsanleitung

TD1166 rev1003 1 - 8

NS1 Installation Guide

INTRODUCTION

Thank you for using NS1 for your access control application. NS1 is a powerful access control system

which can be used for single door access, as well as for connection to any type of on-line access control

system.

NS1 units can also be mounted in an RS485 network without the necessity of an external access control

system.

NS1 as a single door unit offers many possibilities such as:

•Access control

•Unlock option

•Day/Nightlock option (manual or automatic switching)

•Long range reader (up to 45cm)

•Optional use of PIN keypad

•Using an external relay (to prevent potential tampering)

•NS1 Manage software for stand-alone PC programming, event logging and user database

maintenance

REFERENCES

Master card usage is described in the NS1 User Guide (TD1168).

CONNECTIONS

The NS1 uses 12 wire E111235 AWM STYLE 2560 60°C 30V low voltage computer cable. The

connections are indicated below.

Wire Stand-alone Magstripe (ABA) Wiegand

Brown Extra Ground

Violet Relay out (O.C)

Black Ground

Red Power (+11.5 … +12.5V DC)

Yellow RS-485B in +

Blue RS-485B out -

White RS-485A in +

Pink RS-485A out -

Grey IO-1 Door contact input \ RDP output DATA 0

Green IO-2 Ext. Night lock/Rex input \ RCP output DATA 1

Grey/Pink IO-3 Forced entry output \ CLS output STROBE

Red/Blue IO-4 Night lock enabled output \ Access input \ LED

2 - 8 TD1166 rev1003

Figure 1 (below) gives a graphical representation of the connections.

Figure 1 NS1 Connections

Wire

White

Yellow

Pink

Blue

Grey

Green

Grey / Pink

Red / Blue

Violet

Brown

Red

Black

NOTES:

1. The relay output is a 1A / 30V open collector.

2. With the NS1 only DC locks can be used when

directly connected to the NS1.

larm system

Controller

Next reader or

Line Terminator

External Clock

Door contact

Lock or external rela

Power su

12V DC

TD1166 rev1003 3 - 8

NS1 OPERATING LEVELS

The NS1 Proximity Reader has two operating levels:

•Installer Level. On this level the NS1 can be configured by the Installer. This level is also used to do

typical Installer options.

•User Level. On this level typical user options can be set, such as adding and voiding user cards,

setting the door open time, etc.

This Quick Guide explains the most frequently used Installer settings that can be used to configure the

NS1. Please refer to the NS1 User Guide (TD1168) for user related settings.

The programming steps mentioned in this Quick Guide represent a limited number of programming

functions that can be performed by the Installer on an NS1. Please refer to the NS1 Master Manual

(TD0099) for all the possibilities.

NS1 LEDS

The NS1 is provided with seven LEDs which serve as status indicators. Figure 2 illustrates their function.

Figure 2 LED indicators NS1

PROGRAMMING DEVICE

123

789

A remote programmer can be used to configure the NS1 and do settings in the NS1 by

bringing it into the RF field of the NS1.

A programmed function may look like as follows:

The blank “n” in the function indicates an optional number.

An Installer Remote Programmer can set all functions of the NS1.

In this Quick Guide, configuring the NS1 Proximity Reader is described by means of a Remote

Programmer. However, there are other ways. Northern also offers the possibility of programming the NS1

Proximity Reader through the NS1 Manage PC software.

If you have to install this application, please refer to the installation instructions of the NS1 Manage

manual (TD0099).

Led 1 (yellow) Indicates that a card/remote programmer is within range of the NS1.

Led 2 (green) Indicates that access is granted or that the NS1 is in Unlock Mode.

Led 3 (red) Indicates that the door lock is closed.

Led 4 (red) Indicates that the NS1 is in Night Lock mode.

Led 5 (red) Indicates that the NS1 is in Add mode, and that cards are added.

Led 6 (red) Indicates that the NS1 is in Void mode, and that cards are voided.

Led 7 (red) Indicates that the NS1 is in Program mode.

4 - 8 TD1166 rev1003

CONFIGURING THE NS1

The following steps describe how to configure the NS1.

1. Wake up the NS1 from sleep mode.

When powering up the NS1 for the first time, the NS1 is in the Installer sleep mode.

This programmer will automatically become the Installer Remote Programmer. It is

recommended to identify the Remote Programmer as the Installer by labelling it such.

Figure 3 indicates how to wake up the NS1.

1. Power on. (NS1 is in

Installer Sleep mode.)

2. Present a Remote

Programmer in the RF

field of the NS1.

3. Normal operation of the

NS1 is resumed.

Figure 3 Waking up the NS1

2. Set the Lock Type (23*).

Different lock types can be set by entering the key sequence corresponding with the lock type.

See the following table for information.

Lock Type Key sequence Description

Normally open 23*0*

Normally closed 23*1*

The settings “normally open” and “normally closed” are used when a lock

is directly connected to the NS1.

Coded signal 23*2* Coded signal is used to trigger an external relay on the Connection Unit

(article NS1CU). The external relay offers a higher level of security.

The default value is 23*0*. To set another value, take the steps indicated in Figure 4.

1. Enter Program mode by

presenting Installer Remote

Programmer.

2. Enter the choice for the Lock Type, where

“n” is 1 or 2.

3. Normal operation of the

NS1 is resumed.

Figure 4 Setting Lock Type

TD1166 rev1003 5 - 8

3. Set Open Time-out (11*).

Whenever access is granted, the relay of the NS1 will be activated during a certain number of

seconds, called the Open Time-Out.

This period of time can be adjusted from 1 to 255 seconds. The default value is 2 sec, meaning

that after presenting the tag to the NS1 reader, you have 2 seconds to open the door. If you want

to use the default value, skip this step and proceed with the next.

To use a setting other than the default one, perform the steps indicated in Figure 5.

1. Enter Program Mode by

presenting Installer Remote

Programmer.

2. Enter Open Time-out period. 3. Normal operation of the

NS1 is resumed.

Figure 5 Setting Open Time-out Period

4. Set Close Time-out (12*).

The NS1 has a special timer that is intended to check whether the gate or door has been closed

within a specific period of time.

This period of time is adjustable from 0 to 255 seconds. The default value is “0”, meaning that the

function is disabled. If you want to use the default value, skip this step and proceed with the next.

I/O 1 of the NS1 should be connected to ground or to ground via the door switch when

using this option.

To use a setting other than the default one, perform the steps indicated in Figure 6.

1. Enter Program mode by

presenting Installer Remote

Programmer.

2. Enter Close Time-out period. 3. Normal operation of the

NS1 is resumed.

Figure 6 Setting the Close Time-out Period

6 - 8 TD1166 rev1003

5. Set Egress (20*).

Setting egress allows the connection of a push button mounted inside a building to grant passage

when exiting. When set, this option will disable the external Night Lock control which uses the

same I/O 2 input. Egress is low active, i.e. access is granted when I/O 2 is connected to GND for a

short while.

The default option is 20*0*, meaning that this function is disabled. If you want to use the default

value, skip this step and proceed with the next.

To use a setting other than the default one, perform the steps indicated in Figure 7.

1. Enter Program mode by

presenting the Installer

Remote Programmer.

2. Enter Egress option. 3. Normal operation of the

NS1 is resumed.

Figure 7 Setting Egress Option

6. Set NS1 from Installer level to User level.

To prevent tamper alarms, make sure the NS1 cover is in place. If for any reason you

need to go back to the installer level, just present the Installer Remote Programmer in

the RF field of the NS1 and enter 0*1*.

To set the User level, perform the steps indicated in Figure 8.

1. Enter Program mode by

presenting the Installer

Remote Programmer.

2. Press 0*0*. 3. The NS1 goes to User

Sleep mode. Switch the

power OFF.

Figure 8 Set User Level

TD1166 rev1003 7 - 8

SECURITY

For safety precautions the user is strongly advised to keep records of the functions and ID numbers of all

tags and the name of the users. In case of loss, the specific tags can be voided from memory by entering

the specific number using the Remote Programmer.

Privacy

The NS1 is provided with a ‘Protect mode’ by which any (Remote) programming attempt will be blocked,

except the user programmer.

Forced Entry

If a forced entry situation occurs, a continuous alarm will sound. If required, a burglar alarm can be

triggered. This option will only activate when a door contact is connected, and the Close Time-out is not

set to zero. The alarm can be deactivated by repeating the programming procedure for setting the Close

Time-out to zero. The NS1also has an anti-tamper switch and alarm.

Tamper Protection

The NS1 is equipped with an anti-tamper switch and alarm.And becauseit is both compact and it employs

RF technology, it can be mounted behind any material except metal, with a maximum thickness of 5 cm

(2”) for additional tamper protection.

8 - 8 TD1166 rev1003

Honeywell Access Systems

135 West Forest Hill Avenue

Oak Creek, WI 53154

PH: 414-766-1700 FAX: 414-766-1798

www.nciaccessworld.com

Inhaltsverzeichnis

Andere Honeywell Tor Handbücher

Honeywell

Honeywell Notifier 002-467 Bedienungsanleitung

Honeywell

Honeywell NFS-3030 Bedienungsanleitung

Honeywell

Honeywell RedLINK THM6000R1002 Bedienungsanleitung

Honeywell

Honeywell LGW1000 Bedienungsanleitung

Honeywell

Honeywell GW-1000-WE Bedienungsanleitung

Honeywell

Honeywell GENT VIG-BNG Bedienungs- und Wartungsanleitung

Honeywell

Honeywell CIU 888 Bedienungsanleitung

Honeywell

Honeywell CIU 888 Bedienungsanleitung

Honeywell

Honeywell LyricLCP300-L Installations- und Betriebsanleitung

Honeywell

Honeywell INNCOM PC-503 Bedienungsanleitung

Honeywell

Honeywell Experion PKS Bedienungsanleitung

Honeywell

Honeywell RedLINK THM6000R Bedienungsanleitung

Honeywell

Honeywell LCBS Connect Bedienungs- und Wartungsanleitung

Honeywell

Honeywell Notifier MODBUS-GW Bedienungsanleitung

Honeywell

Honeywell RFG100 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER ONYXWorks NFN Gateway Bedienungsanleitung

Honeywell

Honeywell RedLINK Bedienungsanleitung

Honeywell

Honeywell 5824 Technisches Handbuch

Honeywell

Honeywell W7006A Bedienungsanleitung

Honeywell

Honeywell HON-CGW-MBB Bedienungsanleitung

Honeywell

Honeywell NOTIFIER NFN-GW-PC-HNMF Bedienungsanleitung

Honeywell

Honeywell NOTIFIER NFN-GW-PC-W Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell PEHA 940/8 DALI-G Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung