Honeywell Dolphin 60s Bedienungsanleitung
Dolphin™60s
Quick Start Guide
60s-QS Rev A
7/13
Out of the Box
Verify that your carton contains the following items:
• Dolphin 60s mobile terminal
• Rechargeable 3.7V Li-ion Battery
• USB charge/communication cable
• Power adapter with regional plug adapters
• Quick Start Guide
• Compliance Regulatory Sheet
Note: If you ordered accessories for your terminal, verify that they
are also included with the order.
Be sure to keep the original packaging in case you need to return the
Dolphin terminal for service.
Front Panel
Front Speaker
Indicator LED
Touch Panel
Display
SCAN Key
Power/End Call
Key
Microphone
USB Charger
Navigation Keys
Volume Control
Buttons
Programmable
Button
I/O Connector
Headset
Connector
Reset Button
Send Key
Blue Modifier
Key
Red Modifier
Key
Back Panel
Laser/Scan Engine
Rear Speaker
Color Camera
Battery Door
MicroSD Memory
Card and SIM Card
Socket (under
battery)
Stylus Tether
Battery Door Latch
Lanyard Slot
Camera Flash
Keyboard
Numeric Keyboard
QWERTY Keyboard
Installing the Battery Pack
We recommend use of Honeywell peripherals, power cables, and power
adapters. Use of any non-Honeywell peripherals, cables, or power
adapters may cause damage not covered by the warranty.
Ensure all components are dry prior to mating terminals/batteries with
peripheral devices. Mating wet components may cause damage not
covered by the warranty.
Dolphin 60s model terminals are designed for use with battery part
number 60s-BATT-1 (Li-ion 3.7V, 12.358 watt hour) manufactured
for Honeywell International Inc.
The Dolphin 60s is shipped with the battery packaged separately
from the terminal. Perform the following steps to install the battery.
1. Slide the latch to unlock the battery door.
2. Open the battery door.
3. Insert the battery into the battery well with the contacts facing
the top of the unit.
4. Re-install the battery door.
5. Connect the terminal to one of the Dolphin 60s charging periph-
erals to charge the battery pack.
!
!
Removing the Battery Pack
Perform the following steps to remove the battery.
1. Slide the latch to unlock the battery door.
2. Open the battery door.
3. Remove the battery.
Charging the Dolphin 60s
Dolphin terminals ship with the battery significantly discharged of
power. Charge the battery pack with a Dolphin charging device for a
minimum of 6 hours before initial use.
Suspending/Resuming Terminal
To put the device into Suspend mode when the terminal is powered
on:
1. Press and release the Power key for approximately 4-5
seconds.
To resume from the Suspend mode, press and release the Power
key .
HomeBase Parts (Model D60s-HB)
HomeBase LED Indicators
AUX battery LED
Orange The auxiliary battery is charging.
Green The auxiliary battery has completed charging and is ready
for use.
Dock LED
Green The terminal is properly seated in the base.
AUX Battery
Well
Dock LED
USB Port
DC Power Jack
AC Power Cord
Power Adapter
Power Cable
AUX Battery
LED
USB Charge/Communication Cable
(Model USB-WALL-CHARGER-1)
The USB Charge/Communication cable provides two options for
charging the terminal. Use the cable in conjunction with the provided
power supply adapter and plug adapter to charge the terminal from a
power outlet or connect the cable to a high-power USB port to charge
from a host device.
Option 1: Charging from a power outlet
Use only a UL Listed power supply, which has been qualified by
Honeywell with an output rated at 5VDC and 1A with the device.
Option 2: Charging from a high-power USB port on a host device
Note: Charging the battery through a USB port takes more time than
direct AC adapter charging. USB charging will not take place
if the terminal is drawing more current than supplied by the
USB port.
Tap > Settings > System > Power to verify the battery is
charging.
Plug
Adapter
Power
Adapter
Charge/
Communication
Cable
Micro USB
Port
USB Door
Micro
USB Port
Charge/
Communication
Cable
Host Device
USB Port
USB
Door
Resetting the Terminal
There are three types of system resets: a soft reset, a hard reset, or
a factory reset. The soft and hard resets preserve all data stored in
the file system. Contact a Honeywell technical support
representative for more information on how to perform a factory
reset.
Soft Reset (Warm Boot)
A soft reset re-boots the device and preserves any objects created in
RAM. You would perform a soft reset when: the terminal fails to
respond, after installing some software applications, or after making
changes to certain settings, such as network cards.
1. Press and hold the Blue key and then Power key for
approximately 6-7 seconds.
2. When the reset is complete, the Home screen displays.
Hard Reset (Cold Boot)
A hard reset re-boots the device and closes any open applications
running in RAM at the time of reset.
1. Press and hold the Blue key and then Send key for
approximately 6-7 seconds.
2. When the reset is complete, the Home screen displays.
Andere Handbücher für Dolphin 60s
4
Inhaltsverzeichnis
Andere Honeywell Handheld Handbücher
Honeywell
Honeywell MX7 Tecton Bedienungsanleitung
Honeywell
Honeywell 26079 Bedienungsanleitung
Honeywell
Honeywell CT50 Bedienungsanleitung
Honeywell
Honeywell Dolphin CT40 Bedienungsanleitung
Honeywell
Honeywell 7600BP-112-B6EE - Hand Held Products Dolphin... Bedienungsanleitung
Honeywell
Honeywell CK75LAN Bedienungsanleitung
Honeywell
Honeywell Optimus 5100 Bedienungsanleitung
Honeywell
Honeywell Dolphin 99 EX Bedienungsanleitung
Honeywell
Honeywell Dolphin 6000 Bedienungsanleitung
Honeywell
Honeywell GMPT-401-C1D2 Bedienungsanleitung
Honeywell
Honeywell CT50 Bedienungsanleitung
Honeywell
Honeywell SP5700 Bedienungsanleitung
Honeywell
Honeywell MX8 Bedienungsanleitung
Honeywell
Honeywell CT50LON Bedienungsanleitung
Honeywell
Honeywell Dolphin CN85 Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA51 Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA51 Bedienungsanleitung
Honeywell
Honeywell Dolphin 75e Bedienungsanleitung
Honeywell
Honeywell Dolphin CT60 Bedienungsanleitung
Honeywell
Honeywell Dolphin 9900 Bedienungsanleitung
