Honeywell IH25 Bedienungsanleitung

Quick Start Guide

IH25

UHF RFID Reader

IH25-EN-QSG REV A

Mobile Terminal Socket

Power Button

UHF Antenna

Trigger Button

Type C Port

Charging Contacts

MODE Button

Status Indicators

Battery Cover

Release Screws

MODE

Introduction

The IH25 UHF RFID Reader provides Ultra High Frequency (UHF)

Radio Frequency Identiﬁcation (RFID) connected to a mobile

terminal. The unit can read and write to bar code, QR code and

UHF RFID tags.

Install the battery before using the reader for the ﬁrst time.

1. To access the battery compartment, remove the battery cover

screws and then the battery cover.

2. Insert the battery into the battery compartment with the tape at

the bottom.

3. Attach the battery cover and tighten the screws. Note that the

torque should be 3.5kg.f.

Battery Installation and Remove

To uninstall the battery, remove the battery cover screws and

then the battery cover. Pull the tape on the battery to pull the

battery out.

Tape

MODE

3.8V 4000 mAh

Tape

Before using the reader for the ﬁrst time, ensure the battery is fully

charged.

To charge the reader, use the USB cable, the USB cable + AC

charge adapter or a docking station.

Solid amber: Charging

Solid green: Fully charged

USB Charge

AC Charge

Charging

MODE

Honeywell

Power

12V

Use the one slot or four-slot docking station to charge IH25 and

the mobile terminal. Note: when charging, make sure the

charging indicator is always on.

MODE

Honeywell

Power

12V

Docking Station Charge

1. Insert the mobile terminal into the case and press it down.

Note: When installing the bracket, pay attention to the angle and

strength so as not to damage the product.

2. Turn on power to the reader and the mobile terminal.

Use the mobile terminal to scan the QR code on the label

attached at the bottom of the reader’s main body.

code

Fitting Device Case and Attaching Device

3. Check the stud on the bottom of the case and the socket on

the reader are clean and free from dirt or debris.

4. Align the stud with the socket, ensuring that it is parallel, and

press the two parts together ﬁrmly until they click into place.

1. Turn on power to the reader and it beeps one time.

2. Press and hold the MODE button for at least 3 seconds to

switch to RFID mode. The RFID indicator is on and then off after 5

seconds.

3. Press the trigger button to read tags.

RFID tags can be read when they are in range. The range (typical

0.2ft—20ft) at which a tag can be read depends on the tag type

and size and the number of tags in the ﬁeld.

Reading RFID Tags

MODE

MODE Button and Status Indicators

Press the MODE button to light on the current mode light.

Release the button within 3 seconds, the mode light is off.

Press and hold the MODE button for at least 3 seconds to

switch between 1D/2D and RFID mode and the current

mode light is on.

Release the button, the current mode light is off.

Solid amber: Charging

Solid green: Fully charged

Red ﬂash/ Green and amber ﬂash alternately: Charge error

Solid red: Battery low warning (<20% capacity remaining.)

Blue slow ﬂash: Bluetooth disconnected (two beeps

when disconnect from PDA)

Solid blue: Bluetooth connected (one beep when

connected successfully)

Important Safeguards

We recommend the use of Honeywell accessories and power

adapters. Use of any non-Honeywell accessories or power

adapters may cause damage not covered by the warranty.

We recommend use of Honeywell Li-ion battery packs. Use

of any non-Honeywell battery may result in damage not

covered by the warranty.

Ensure all components are dry prior to mating the unit and

batteries with peripheral devices. Mating wet components

may cause damage not covered by the warranty.

Ensure all components are dry prior to placing the battery in

the unit. Mating wet components may cause damage not

covered by the warranty.

Andere Handbücher für IH25

Inhaltsverzeichnis

Andere Honeywell RFID-System Handbücher

Honeywell

Honeywell IH25 Bedienungsanleitung

Honeywell

Honeywell Connected Home SPR-S8EZS Bedienungsanleitung

Honeywell

Honeywell IH45 Bedienungsanleitung

Honeywell

Honeywell IM11-PRT Bedienungsanleitung

Honeywell

Honeywell IH25 Bedienungsanleitung

Honeywell

Honeywell 026366.00 Bedienungsanleitung

Honeywell

Honeywell Home SPR-S8EZS Bedienungsanleitung

Honeywell

Honeywell IH40 Bedienungsanleitung

Honeywell

Honeywell IF1C Bedienungsanleitung

Honeywell

Honeywell ARC-X Bedienungsanleitung

Beliebte RFID-System Handbücher anderer Marken

Chainway

Chainway R1 Bedienungsanleitung

IFM

IFM DTC600 Bedienungsanleitung

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Bedienungsanleitung

RHOMBUS

RHOMBUS DR20 Bedienungsanleitung

Sirit

Sirit IDentity 6204 Bedienungsanleitung

SOREX

SOREX FLEX Bedienungsanleitung

Omron

Omron V780-HMD68-EIP-KR Bedienungsanleitung

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Gebrauchsanweisung

Shuttle

Shuttle BR06 Gebrauchsanweisung

Digilock

Digilock Curve Keypad Basic Bedienungsanleitung

Atid

Atid AT870 Bedienungsanleitung

Chacon

Chacon 34958 Bedienungsanleitung

Paxton

Paxton PROXIMITY architectural reader Bedienungsanleitung

CipherLab

CipherLab 1800 series Bedienungsanleitung

Brady

Brady FR22 Bedienungsanleitung

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Bedienungsanleitung

Unitech

Unitech RH767 Bedienungsanleitung

Elatec

Elatec TCPConv Bedienungsanleitung