Honeywell ADEMCO VISTA 10P Bedienungsanleitung

SYSTEM

ENHANCEMENT

MODULE

Honeywell/ADEMCO VISTA®

INSTALLATION GUIDE

INSTALL WIZARD AVAILABLE AT 

DUAL PATH

EQUIPMENT

TOOLS AND SUPPLIES NEEDED

• Small blade screwdriver and Phillips screwdriver

• Drill and bits for screws and/or wall anchors

• Four-conductor, 22-gauge or larger stranded wire

• Alpha keypad

OVERVIEW

The System Enhancement Module (SEM) can be used with

Honeywell/ADEMCO VISTA-10P, VISTA-15P, and VISTA-20P panels to

enable wireless reporting of alarms and other system events over the

wireless cellular network and optional broadband Ethernet. The SEM

is intended to be used as the primary communication path for all alarm

signaling to the central monitoring station. The wireless alarm signaling

and routing service is operated by Alarm.com. The SEM also features

integrated support for Alarm.com’s home automation services with

built-in Z-Wave capabilities.

Alarm.com strongly recommends installing an alpha keypad with at least 32

zones to ensure the “Communication Failure” trouble condition is displayed to

the user. See FAQs for more information.













TABLE OF CONTENTS

Step 1: Verify Panel Compatibility ....................................4

Step 2: Create an Account ..................................................5

Step 3: Enable Keypad Address.........................................6

Step 4: Disconnect Power from Panel .............................7

Step 5: Mount the SEM........................................................8

Step 6: Wire the SEM to the VISTA Panel.......................9

Step 7: Power Up the Panel.................................................10

Add & Delete Z-Wave Devices...................................................11

Touchscreen Keypads...................................................................14

Panel Settings................................................................................15

LEDs ................................................................................................. 16

FAQs .................................................................................................19

Troubleshooting............................................................................. 21

 ................................................................................22

Regulatory Information ..............................................................23

SEM Quick Tips..............................................................................24

STEP 1: VERIFY PANEL COMPATIBILITY

The SEM is compatible with Honeywell/ADEMCO VISTA-10P, -15P, and

-20P panels and the equivalents below, dating back to 2005. The date

will be printed on the chip inside the panel as shown below.

Honeywell/ADEMCO

VISTA-10P

Honeywell/ADEMCO VISTA-10PSIA

First Alert FA130CP

First Alert FA130CPSIA

Honeywell/ADEMCO

VISTA-15P

Honeywell/ADEMCO VISTA-15PSIA

First Alert FA148CP

First Alert FA148CPSIA

Honeywell/ADEMCO

VISTA-20P

Honeywell/ADEMCO VISTA-20PSIA

First Alert FA168CPS

First Alert FA168CPSSIA

Please see the Alarm.com Partner Portal Knowledge Base

(www.alarm.com/dealer) for the most up to date list of compatible panels.

TOUCHSCREEN KEYPADS

Touchscreen keypad compatibility details can be found on page 14.

Some system changes will not be processed by Alarm.com

unless the touchscreen keypad is used in Console Mode.

The SEM is not compatible with POTS. The SEM should

be the only communication path for alarm signaling to

the central station.

STEP 2: CREATE AN ACCOUNT



We recommend creating the account at least 24 hours prior to installation.

This will ensure that the SEM is activated prior to installation. To create an

account go to the Alarm.com Partner Portal or MobileTech and log in. You

will need the following information to create the account:

• Customer Address

• Customer Phone Number

• Customer Email Address

• Preferred Login Name for the Customer

• Alarm.com Module Serial Number

• Existing Panel Installer Code

During Step 4 of the “Create New Customer” process, you will be prompted

to enter the current Installer Code on the panel. Alarm.com will use this

code to access panel programming and read information stored on the

panel.

At the end of the “Create New Customer” process, you will be able

to print or email a Welcome Letter for the customer, which includes

STEP 3: ENABLE KEYPAD ADDRESS

ENABLING KEYPAD 8 DEVICE ADDRESS 23

The SEM communicates with the VISTA panel as if it is a keypad.

By default, the SEM will use Keypad 8 Device Address 23 to

communicate. Address 23 must be enabled via panel programming.

To do this, enter programming and select *196 + [1] + *99 at the keypad.

IF ADDRESS 23 IS ALREADY IN USE

In most cases, Address 23 will be available. If another keypad is already



keypad address. You can do this by using the DIP switches on the SEM,

as pictured below.

1. Identify an available keypad address.

2. Using the chart below, change the DIP switches on

the SEM to match the corresponding keypad address.

3. Enable the address by entering the corresponding

VISTA programming command at the panel.

If the correct keypad address is not enabled, repeated

reports of Panel Malfunction will be shown in the Event

History on the Partner Portal or MobileTech once the

SEM is powered on and connects to the network.

Keypad

Address

DIP Switch

Setting

VISTA

Programming Menu

17 None—all OFF *190

18 Switch 4 ON, others OFF *191

19 Switch 3 ON, others OFF *192

20 Switch 3 and 4 ON, others OFF *193

21 Switch 2 ON, others OFF *194

22 Switch 2 and 4 ON, others OFF *195

23 Switch 2 and 3 ON, others OFF *196

STEP 4: DISCONNECT POWER FROM PANEL



panel is disarmed. Next, remove panel AC Power and disconnect the

backup battery.

This is necessary to prevent damaging the panel

or module while making wiring connections.

STEP 5: MOUNT THE SEM

You must be free of static electricity before handling electronic

components. Touch a grounded metal surface before touching

the circuit board.

Press down on the bottom tabs of the enclosure cover to remove it

and set it aside.

Carefully remove the SEM circuit board by depressing the interior

bottom tab.

Place the SEM back plate on the wall at the desired mounting

location and mark the three mounting holes as shown below.

Set the back plate aside and drill holes at the mounting locations.

Use wall anchors where studs are not present and secure the back

plate to the wall with the enclosed screws.

Insert the SEM circuit board back into the back plate.

STEP 6: WIRE THE SEM TO THE VISTA PANEL

Verify panel AC Power is removed and

the backup battery is disconnected.

• Connect panel terminal 4 (GND) to SEM GND.

• Connect panel terminal 6 (GREEN: DATA IN FROM KEYPAD)

to GREEN (OUT).

• Connect panel terminal 7 (YELLOW: KEYPAD DATA OUT)

to YELLOW (IN).

• Use the included red cable with the two prong battery connector

to connect the battery to both the SEM and the panel. For a power-

limited circuit, ensure the fuse is inside the VISTA panel.

Once wiring is complete, route the antenna(s) outside of the enclosure,

away from the SEM, and replace the enclosure cover. Please note that

the antenna(s) should be routed through the second and third channel

openings at the top of the enclosure (see zoom view below).

12V Battery

VISTA Panel

GND

5+12V

GREEN (DATA IN)

YELLOW (DATA OUT)

SEM

+12V

YELLOW (IN)

GREEN (OUT)

GND

CDMA/HSPA

Modules

LTE Modules

The zone scan will automatically begin after the panel is powered up.

On the keypad you will see a series of disarms and programming setting

changes before seeing “MODEM COMM” on the screen.

STEP 7: POWER UP THE PANEL

Connect the backup battery and restore AC power to the panel.

For the SEM to interact with the existing zones on the system, it must

read them from the VISTA panel. The SEM will do a “zone scan” to read

this information.

Additionally, the SEM will automatically set the panel settings needed

for the SEM to communicate. These settings can be found on page 15.

ZONE SCAN

~3 minutes

Do not touch the panel or keypad.

When the zone scan is complete the keypad will display the home screen.

This process will take less than 3 minutes.

Now that the zone scan is complete, the Equipment list should be updated

on the Partner Portal and the Installer and Master User codes should be

synced with the SEM.

ZONE SCAN

COMPLETE

Ready to Arm

If you do not see the MODEM COMM message appear on the

keypad during zone scan and instead notice the keypad scrolling

through each zone individually, the SEM is using an alternate



leave programming before interacting with the panel. Resync

the panel master code with the SEM by changing the Master

Code at the panel or through the Customer Website.



For Broadband Ethernet,

connect the provided Ethernet

Dongle to the connector on the SEM.

Connect the Ethernet cable to the

provided Ethernet Dongle.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitssystem Handbücher

Honeywell

Honeywell LYNX Touch L5210 Series Installationshandbuch

Honeywell

Honeywell Code Encryptor II Bedienungsanleitung

Honeywell

Honeywell WAVE2EX - Ademco Two Tone Siren Montageanleitung

Honeywell

Honeywell ADEMCO VISTA-12A Montageanleitung

Honeywell

Honeywell Galaxy Flex V3 Series Benutzerhandbuch

Honeywell

Honeywell ADEMCO VISTA-40 Montageanleitung

Honeywell

Honeywell LYNX Touch Series Montageanleitung

Honeywell

Honeywell ADEMCO VISTA-15PSIA Montageanleitung

Honeywell

Honeywell SEF8MS Bedienungsanleitung

Honeywell

Honeywell SF340F Bedienungsanleitung

Honeywell

Honeywell ADEMCO LYNXR-I Security System Bedienungsanleitung

Honeywell

Honeywell ADEMCO VISTA-20PSIA Bedienungsanleitung

Honeywell

Honeywell First Alert FA130CP Bedienungsanleitung

Honeywell

Honeywell FBII OMNI 600 Bedienungsanleitung

Honeywell

Honeywell TCPA1BS Bedienungsanleitung

Honeywell

Honeywell ADEMCO VISTA-12A Bedienungsanleitung

Honeywell

Honeywell VISTA-250FBPT Montageanleitung

Honeywell

Honeywell LYNX Touch L7000 Series Bedienungsanleitung

Honeywell

Honeywell Vista 21IP Bedienungsanleitung

Honeywell

Honeywell X-618 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5809 Montageanleitung

Honeywell

Honeywell ADEMCO VISTA-10P Betriebsanleitung

Honeywell

Honeywell VISTA-21iP Montageanleitung

Honeywell

Honeywell Lyric SIXSIREN Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung