Honeywell INTELLIGUARD 9000 Bedienungsanleitung

INTELLIGUARD

9000™

USER’S GUIDE

INTELLIGUARD 9000™

SECURITY SYSTEM

NOTICE

The Canadian Department of Communications label identifies certified

equipment. These certification means that the equipment meets certain

telecommunications network protective, operational and safety requirements.

The Department does not guarantee the equipment will operate to the user’s

satisfaction.

Before installing this equipment, users should ensure that it is permissible to

be connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection.

In some cases, the company’s inside wiring associated with a single line

individual service may be extended by means of certified connector assembly

(telephone extension cord). The customer should be aware that compliance

with the above conditions may not prevent degradation of service in some

situations.

Repairs to certified equipment should be made by ;an authorized Canadian

maintenance facility designated by the supplier.Any repairs or alterations

made by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines and internal metallic water

pipe system, if present, are connected together. This precaution may be

particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but

should contact the appropriate electrical inspection authority, or electrician, as

appropriate.

The Load Number (LN) assigned to each ;terminal device denotes the

percentage of the total load to be connected to the telephone loop which is

used by the device, or prevent overloading. The termination on a loop may

consist of any combination of devices subject only to the requirement that the

total of the Load Numbers of all the devices does not exceed 100.

The Load Number of this unit is 3 .

WARNING: This equipment generates, uses and can radiate radio grequency energy, and if not

installed and used in accordance with the Instructions Manual, may cause interference with radio

communication. It has been tested and found to comply with the limits for a Class A computing

device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference, in which case, users at their own

expense will be required to take whatever measures may be required to correct the interference.Any

unauthorized modification of this equipment may result in the revocation of the owner’s authority to

continue its operation.

This User’s Guide applies to Intelliguard 9000 and Intelliguard 4900

systems.

Welcome

Customized Security atYour Service .................................................. 5, 6

Control Center

Quick User Guide ................................................................................... 7

Area Keypad

Quick Reference Guide........................................................................... 9

Control Center Command

Arming

Using Help to find anArea ................................................................... 11

Arm anArea with a Code ..................................................................... 12

Arm SeveralAreas with a Code ............................................................ 13

Disarming

Disarm an Area with a Code ................................................................. 15

Disarm SeveralAreas with a Code ........................................................ 16

Disarm an Area with two Codes............................................................ 17

Testing

Testing Hold-upActuators .................................................................... 19

Testing of all Actuators ......................................................................... 20

Viewing

View Arm Status................................................................................... 21

View Alarm Status ................................................................................ 22

View Area Status .................................................................................. 23

View Point Status.................................................................................. 24

View System Events ............................................................................. 25

Resetting Detectors

Reset Detectors..................................................................................... 27

Bypassing a Point

Bypass a Point ...................................................................................... 29

UnBypassing a Point

Unbypass Point..................................................................................... 31

Late Closing

Schedule a Late Closing ....................................................................... 33

Force Arming

TABLE OF CONTENTS

(continued on page 4)

ForceArm of a Defective Area.............................................................. 35

PartialArming

Arm an Area’s Perimeter Points, Excluding Interior Points ................... 37

ID Number Management

Add New ID Number ......................................................................39, 40

Delete ID Number ................................................................................ 41

Authority Levels ................................................................................... 42

Modify ID Number..........................................................................43, 44

Code Entry

Code Entry ........................................................................................... 45

Enter New Code ................................................................................... 46

Modify Code ........................................................................................ 47

Reference Guide

Service ................................................................................................. 49

Definitions and Abbreviations ............................................................... 51

Message Description........................................................................52, 53

Customized Security atYour Service

Your Intelliguard 9000™ is a very powerful security system that is equally

practical, since it is customized to your business and security needs, even

as they change.

This brief survey of the Intelliguard 9000™ structure and basic operation

will familiarize you with the key words used (in bold). We recommend

that you read it first, to understand this and how your system operates.

Area Controlled Security

Your facility may be divided in as many as eight different security areas.

An area may be your warehouse, your production area, or even a given

office. Each area has its own arming schedule and authorized users.

Several special areas may also be defined in your system:

• The linked areas; an area can be linked to another security area so it

automatically turns off when the first area disarms.

• The master area arms and disarms the slave areas.

Individual Points of Protection

When you arm an area, a series of detectors or detection points such as

door contacts, motion, and heat detectors are activated. The type of risks

against which you want to protect yourself, determines what combination

of detectors to use in each area.

User Friendly Control Centers andArea Keypads

Control centers and area keypads can be installed in strategic places in

order for you to communicate with the system.You may arm and disarm

an area using the keypad.

Up to four control centers can be connected to one Intelliguard 9000™

control unit to allow system operation from several different locations in

the facility. The display of the control center assists you with each

command, indicating precisely the origin of an authorized entry, an alarm

or a problem.

Up to eight area keypads may also be connected, with each keypad

controlling a single area. A quick reference guide may be pulled from the

WELCOME

top of the area keypad to help you review each operation.

Menus Structure of the Control Center

With the Intelliguard 9000™ you perform different commands as easily as choos-

ing plates from a menu. In fact, there are Quick command keys as well as two menu

keys on the Intelliguard 9000™ control centers. For frequently used functions such

as arm, disarm and test, these Quick command keys make your life easier. The

other system functions are available using the mode or option keys. The control

center guides you through the chosen menu to the function you need.

Passcode Access withAuthority Levels

All system users, received a user passcode with assigned authority level.Your

passcode identifies you as an authorized system user, while the authority level

determines which areas you are allowed to access and the commands and changes

you may perform.

Your passcode is divided in two parts. The two-digit ID which is assigned to you by

the system administrator is the first part. The second is the CODE, a personal and

secret four-digit number you must enter on the keypad each time you access the

system.

Some operations require two codes if greater security is desired.

Security through Honeywell Monitoring

Honeywell monitoring provides a complete supervision of your system, 24 hours a

day, by qualified professionals. Each alarm transmits a signal to the Honeywell

Customer Service Center. When an emergency situation occurs, the efficiency and

know-how of the monitoring station personnel may be the difference between a

minor incident and important losses.

Using this Guide

Not that you have an idea of what the Intelliguard 9000™ is all about, you are

ready to learn how to use it daily. Each section in this Guide describes a series of

commands, such as those used to arm or disarm the system. The Guide walks you

through the command structure, explaining what to do at each step, what you see on

the control center display as well as the area keypad, and what happens in the

system.You will soon realize how easy it is to operate the Intelliguard 9000™.

However, Honeywell recommends that you keep this Guide nearby.

CONTROL

CENTER

CONTROL CENTER

1. Quick User Guide

ARM

DISARM

HELP ACCESS TO:

CUSTOMER SUPPORT

PHONE NO. ADDITIONAL

LOG OR AREA INFORMATION

DISPLAY

SCROLL UP

CANCEL

SCROLL DOWN

MODE ACCESS TO:

SYSTEM STATUS

RESET DETECTOR (HU)

EVENT LOG

RESET LOG

CONFIGURATION

ARM PARTIAL

REPRINT LOG

TEST ACCESS TO:

HOLD-UP TEST

CHIME

WALK TEST

OPTIONS ACCESS TO:

BYPASS A POINT

UNBYPASS A POINT

ID. MANAGEMENT

CHANGE CODE

SCHEDULES

TIME CHANGE M16338

CONTROL

CENTER

1. Quick User Guide

AREA KEYPAD

QUICK REFERENCE

ID-CODE

POINT STATUS

AREA STATUS

ARM & FUNCTIONS

(DISARM)

RED

YELLOW

GREEN

FLASHING

OFF

GREEN

RED

FLASHING

= Enter [ID]

= Enter [CODE]

=Valid

= Enter 2d

[ID] [CODE]

= See point

status

= Ready to arm

= Armed

= Exit delay

OFF

FLASHING

= Ready

= Not Ready

= Alarm

memory

= Arm

= Reset detedtors

= Force arm

= Arm partial

= Change code

[New code twice]

= Reset alarm

memory

Enter [ID] [CODE] followed by

- Maximum 10 seconds between key entries

M16339

AREA KEYPAD

Andere Handbücher für INTELLIGUARD 9000

Inhaltsverzeichnis

Andere Honeywell Sicherheitssystem Handbücher

Honeywell

Honeywell L5200 Series Montageanleitung

Honeywell

Honeywell VISTA-21iP Betriebsanleitung

Honeywell

Honeywell 013002 Bedienungsanleitung

Honeywell

Honeywell MAXPRO MPIP2000U Series Montageanleitung

Honeywell

Honeywell Galaxy 8 Bedienungsanleitung

Honeywell

Honeywell SF340F Bedienungsanleitung

Honeywell

Honeywell Activ8 COLOUR Bedienungsanleitung

Honeywell

Honeywell Code Encryptor II Bedienungsanleitung

Honeywell

Honeywell OMNI-408 Bedienungsanleitung

Honeywell

Honeywell Home SI800MS Bedienungsanleitung

Honeywell

Honeywell VISTA-20PSeries Bedienungsanleitung

Honeywell

Honeywell L5200 Series Betriebsanleitung

Honeywell

Honeywell LYNX Touch L5210 Series Bedienungsanleitung

Honeywell

Honeywell LYNX Touch L5210 Series Montageanleitung

Honeywell

Honeywell Esser 804950 Bedienungsanleitung

Honeywell

Honeywell Galaxy Dimension Gebrauchsanweisung

Honeywell

Honeywell X-618 Bedienungsanleitung

Honeywell

Honeywell ADEMCO Vista-12C Montageanleitung

Honeywell

Honeywell Fire-Lite Alarms W-BG12LX(A) Bedienungsanleitung

Honeywell

Honeywell ADEMCO 6150V Bedienungsanleitung

Honeywell

Honeywell ADEMCO VISTA SERIES Montageanleitung

Honeywell

Honeywell Galaxy 3-48C Betriebsanleitung

Honeywell

Honeywell ADEMCO LYNXR-I Security System Bedienungsanleitung

Honeywell

Honeywell VISTA-21iP Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung