Honeywell 43191680-105 Bedienungsanleitung

X-XX UL

INSTALLATION INSTRUCTIONS

43191680-1

AuxiliarySwi

tch

APPLICATION

The 43191680-105 Dual Auxiliary Switch provides two

independent, spdt switching functions. Switching points

are adjustable over the full length of the actuator stroke; for

example, the switch can be used to switch pumps at any

point or to provide remote indication of any specific stroke

position. These switches are used with valve actuators as

shown in Table 1. The switches are furnished factory wired

to the terminal block. Fig. 1 illustrates the parts furnished

with this switch and the wiring connections.

IMPORTANT

These switches are rated at 24 Vac maximum.

Table 1. Applicable Actuators for

43191680-105 Dual Auxiliary Switches.

Fig. 1. Auxiliary switch parts and wiring.

6 4 5 9 7 8

C8394

1 2 3 4 5 6

331122

S1 S2

INSTALLATION

When Installing this Product...

1Read these instructions carefully. Failure to follow

them could result in the equipment not operating

properly.

2Check the part numbers in the preceding section to

be sure that the product is suitable for your applica-

tion.

3The installer must be a trained, experienced service

technician.

4After completing installation, use these instructions

to check product operation.

CAUTION

Disconnect the power supply to the auxiliary

potentiometer and actuator before beginning

installation to prevent electrical shock or equip-

ment damage.

Mounting, Connecting, andAdjusting

1Remove actuator cover.

2Mount the auxiliary switch assembly and terminal

label on the actuator base. Make sure the two tabs

on the bottom of the switch assembly slip snugly into

the slots provided. See Fig. 2.

Fig. 2. Installing auxiliary switch assembly.

3Secure auxiliary switch assembly by pressing top

back until assembly snaps into place. See Fig. 3.

S1 S2

C8393

6 4 5 9 7 8

63-2524

Actuator Spring Action on

Power Failure

ML6425A Extends stem

ML6425B Retracts stem

ML7425A Extends stem

ML7425B Retracts stem

63-2524 2

43191680-105 AUXILIARY SWITCH

Fig. 3. Securing auxiliary switch assembly.

4Secure terminal block and terminal label with Phillips

head screws. See Fig. 4 .

Fig. 4. Securing terminal block and label.

CAUTION

The manual spring handle is under tension and

could turn quickly when lifted resulting in injury to

fingers pinched between the handle and plastic

casing. Maintain handle orientation while lifting and

remove fingers quickly when releasing.

5Remove manual spring handle retaining clip, if

necessary, and lift and release the handle. See

Fig. 5. The easiest way to perform this operation

safely is to:

a. Remove the retaining clip (shipping stop) and

discard.

b. Wedge a small, flat-bladed screwdriver under

the manual spring handle at the point marked

in Fig. 5 and pry up the handle.

Fig. 5. Removing spring retaining clip

and releasing manual spring handle.

6Adjust switching point for each switch. See Fig. 6.

a. Using manual spring handle on the actuator,

adjust the actuator shaft to the required

switching point for Switch S1.

NOTE: Turning the spring handle clockwise

extends the actuator shaft. When the

shaft gets to the required position,

press the handle down to hold the

shaft in position. Turning the spring

handle requires two hands, one to

turn the handle and the other to hold

it in place on each consecutive turn.

Observe the preceding caution and

release the handle only as noted in

the preceding Step 5.

b. Loosen the Phillips head set screw on the

cam for Switch S1, set the cam to the required

position, and tighten the set screw.

c. Repeat the preceding Steps 6a and 6b for

Switch S2.

C8395

S1 S2

C8396

S1 S2

4 MM

3 MM

M6629

63-2524

43191680-105 AUXILIARY SWITCH

Fig. 6. Adjusting switching points.

C8397

S1 S2

1 X MAX.

100

Wiring

Route field wiring in through the conduit opening in the

bottom of the actuator, connect to the switch assembly

terminal block according to the job drawings, and replace

the actuator cover. See Fig. 1 for terminal identification.

CAUTION

Disconnect the power supply to the auxiliary

switches and actuator before wiring to prevent

electrical shock or equipment damage.

All wiring must comply with local codes, regulations, and

ordinances.

CHECKOUT

Drive actuator shaft fully up and fully down and check the

function of the auxiliary switches in the control system.

63-2524 4

43191680-105 AUXILIARY SWITCH

Home and Building Control

Honeywell Limited-Honeywell Limitée

155 Gordon Baker Road

North York, Ontario

M2H 2C9

Helping You Control Your World®

63-2524 G.C. 1-97 Printed in U.S.A

Home and Building Control

Honeywell Inc.

Honeywell Plaza

P.O. Box 524

Minneapolis, MN 55408-0524

Andere Honeywell Schalten Handbücher

Honeywell

Honeywell GSS Series Bedienungsanleitung

Honeywell

Honeywell C6045D Bedienungsanleitung

Honeywell

Honeywell B Bedienungsanleitung

Honeywell

Honeywell 14CE101 Bedienungsanleitung

Honeywell

Honeywell MICRO SWITCH BX Series Bedienungsanleitung

Honeywell

Honeywell ADEMCO 270R Montageanleitung

Honeywell

Honeywell CX Series Kurzanleitung

Honeywell

Honeywell RPLS530A Bedienungsanleitung

Honeywell

Honeywell C6097 Bedienungsanleitung

Honeywell

Honeywell PEHA PHC Benutzerhandbuch

Honeywell

Honeywell Switches Bedienungsanleitung

Honeywell

Honeywell 968XTP Bedienungsanleitung

Honeywell

Honeywell MAXPRO-Net Montageanleitung

Honeywell

Honeywell RXSW100A3CULH Bedienungsanleitung

Honeywell

Honeywell DCM/SN DIFF Bedienungsanleitung

Honeywell

Honeywell Fema DCM-203-574 Series Bedienungsanleitung

Honeywell

Honeywell Krom Schroder DL A Series Bedienungsanleitung

Honeywell

Honeywell HDLS Series Service-Handbuch

Honeywell

Honeywell 50054911 Bedienungsanleitung

Honeywell

Honeywell Limitless WGLA Series Bedienungsanleitung

Honeywell

Honeywell C437D Bedienungsanleitung

Honeywell

Honeywell PK 80148 Bedienungsanleitung

Honeywell

Honeywell 272630D Bedienungsanleitung

Honeywell

Honeywell 88173 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch