Honeywell RT10W Bedienungsanleitung
RT10W
Rugged Tablet with Windows 10 IoT
Quick Start Guide
RT10W-EN-QS-01 Rev B
7/20
1
Out of the Box
Make sure that your shipping box contains these items:
• RT10W rugged tablet
(Model RT10WL00 or RT10WL10)
• Rechargeable 7.7 VDC Li-polymer battery
• Power supply (power cord sold separately)
•Stylus
• Product Documentation
If you ordered accessories for your tablet, verify that they are
also included with the order. Be sure to keep the original
packaging in case you need to return the tablet for service.
Note: RT10WL00 models do not include a WWAN radio.
Memory Card Specifications
Honeywell recommends the use of Single Level Cell (SLC)
industrial-grade microSD™ or microSDXC™ memory cards with
RT10 tablets for maximum performance and durability. Contact
a Honeywell sales representative for additional information on
qualified memory card options.
2
Tablet Features
Microphone
Touch
Screen
Menu Button
Fn1 Button Power Button
Front Camera
Kensington Lock Port
Bar Code Scanner
(model dependent)
I/O
Cover
Light Sensor and
LED Indicators:
-RF communication
-Disk activity
-Battery
-Power
I/O Panel
(I/O cover open)
Power Jack
Audio Jack
USB-A Port
MicroSD Card Slot
USB-C Port Micro HDMI Port
3
Camera Flash
Micro SIM Card
Cover/Slot
Speaker
Battery
Speaker
Docking
Connector
Battery
Lock
Battery
Release
Stylus
Rear Camera
Fn2
Button
Volume/
Brightness
Button
Extension Port
(cover not shown)
Laser Safety Label Location
(model dependent)
4
Install a Micro SIM Card
Only RT10WL10 (WWAN) models support micro SIM card use
for cellular phone features.
Do not squeeze or disconnect cables when removing
or inserting the 3G/LTE module.
12
34
56
5
Note: Always power off the tablet before attempting to install or
remove a card.
Install a microSD Card (Optional)
Note: Format the microSD card before initial use.
7
9
8
10
6
Note: Always power off the tablet before attempting to install or
remove a card.
Install the Battery
The RT10W ships with a Li-poly 7.7 VDC, 45.43 watt-hour
battery manufactured for Honeywell International Inc.
12
2
4
3
1
7
Charge the Tablet
The RT10 rugged tablet ships with a partially charged battery.
Charge the battery for a minimum of 6 hours.
We recommend using AC power when you start the tablet for the
first time.
We recommend use of Honeywell Li-poly or Li-ion
battery packs. Use of any non-Honeywell battery may
result in damage not covered by the warranty.
Ensure all components are dry prior to placing the
battery in the computer. Mating wet components may
cause damage not covered by the warranty.
We recommend the use of Honeywell accessories and
power adapters. Use of any non-Honeywell
accessories or power adapters may cause damage not
covered by the warranty.
Ensure all components are dry prior to mating the
computers and batteries with peripheral devices.
Mating wet components may cause damage not
covered by the warranty.
12
8
Set Up the Tablet for the First Time
The first time you power on the tablet, a Welcome screen
appears. Once setup is complete, the Welcome screen no longer
displays on startup.
1. Press and hold the Power button for approximately
3 seconds until the blue LED power indicator lights up.
2. Using your finger or the stylus, select your region and then
touch Yes.
3. Follow the on-screen prompts to finish setting up the tablet.
Turn the Power On or Off
To turn the tablet on:
•PressandholdthePower button for approximately 3 seconds
until the blue LED power indicator lights up.
To turn the tablet off:
1. Touch .
2. Touch .
If a power interruption occurs during Windows set
up, access the Recovery menu by pressing the Fn1
button.
Do not press the power button repeatedly.
Do not attempt to connect or disconnect the AC
adapter or press the tablet’s screen, buttons or
external keyboard/mouse until the Disk Activity
indicator turns off.
9
3. Touch Shut down.
Battery Replacement
Hot Swap
The RT10W Tablet has an internal backup battery that is
charged with the main battery. This battery cannot be removed
and requires adequate power for main battery hot swapping.
When the backup battery is fully charged, the tablet can sustain
up to 5 minutes of runtime for battery hot-swapping.
1. Press the Menu button or double-tap to open the Hottab
app.
2. Touch Setting to check the power level of the backup
battery.
3. If the backup battery level is at least medium, remove the
main battery. Otherwise, charge the tablet until the backup
battery level is medium or higher before removing the main
battery.
4. Insert a new, fully charged battery into the battery
compartment.
Sleep Mode
Sleep mode automatically turns the touch panel display off and
locks the tablet to save battery power when the tablet is inactive
for a programmed period of time.
Charge the built-in backup battery every two months
to maintain battery health and prevent possible
issues from battery over-discharge.
Andere Handbücher für RT10W
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Honeywell Tablette Handbücher
Honeywell
Honeywell ScanPal EDA71 Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA71 Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA10A Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA71 Bedienungsanleitung
Honeywell
Honeywell EDA70-3 Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA70 Bedienungsanleitung
Honeywell
Honeywell ScanPal EDA71 Bedienungsanleitung
Honeywell
Honeywell RT10A Bedienungsanleitung
Honeywell
Honeywell RT10W Bedienungsanleitung
Honeywell
Honeywell RT10A Bedienungsanleitung
