Honeywell DR4300 Series Leitfaden

Form 44-45-33-37B Page 1 of 3

Models DR4200, DR4300, and

DR4500 Recorders

Replacement Instruction

Chart Motor Kit (30756113-501)

Document Number Form: 44-45-33-37B

Effective: 12/98

Supersedes: 3/98

Kit Contents This Chart Motor Replacement Kit contains the following parts:

Description Quantity Used On

•Chart Motor 1 All models

•Chart Hub Kit 1 All models

•Tie Wraps 4 All models

•Screws, Plastite #4 x .313 2 Newer models without

brass inserts

•Screw/Lockwasher #4 x .25 2 Older models with

brass inserts

Summary Enclosed is a new chart motor assembly with parts required to replace the

chart motor in a DR4200, DR4300, or DR4500 recorder. Use the

following procedures, as appropriate, to replace the existing chart motor

assembly.

WARNING Never access components inside the case, or remove or

install any connectors, with power applied.

Continued next page

Kit Instruction, continued

Page 2 of 3 Form 44-45-33-37B

Component Location Refer to Figure 1 for the component locations and Table 1 for the

for DR4200/DR4300 installation procedure.

Screws 24240

Figure 1 – Component Location

DR4200/DR4300 Follow the procedure in Table 1 to replace the existing chart motor

Procedure assembly in your recorder.

Table 1 –

Chart Motor Assembly Replacement for DR4200/DR4300 Recorders

Step Action

1Open the chart door and swing the chart plate out.

2 Remove chart hub (front of chart plate) and chart motor (rear

of chart plate) by removing screws. Cut tie wraps securing

leads to chart plate (if applicable). Discard motor and hub;

save screws.

3 Use new tie wraps to re-bundle new motor leads.

4 Refer to Chart Hub instruction sheet (steps 3-6) for

remaining steps.

Kit Instruction, continued

Form 44-45-33-37B Page 3 of 3

Component Location Refer to Figure 2 for the component locations and Table 2 for the

for DR4500 installation procedure.

Chart

Hub

Chart Motor

Spring

24241

Figure 2 – Component Location

DR4500 Procedure Follow the procedure in Table 2 to replace the existing chart motor

assembly in your recorder.

Table 2 – Chart Motor Assembly Replacement for DR4500 Recorder

Step Action

1Open the chart door and swing the chart plate out.

2Remove chart hub and motor assembly by removing screws

and cutting tie wraps. Discard hub and motor, but save

screws.

3 Use new tie wraps to re-secure wires.

4 Refer to Chart Hub replacement instructions (steps 3-6) for

remaining steps.

Andere Handbücher für DR4300 Series

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Diktiergerät Handbücher

Honeywell

Honeywell DPR180 Bedienungsanleitung

Honeywell

Honeywell DR4300 Series Bedienungsanleitung

Honeywell

Honeywell DR4500A Handbuch

Honeywell

Honeywell X Series Bedienungsanleitung

Honeywell

Honeywell X Series Bedienungsanleitung

Honeywell

Honeywell DR4300 Series Leitfaden

Honeywell

Honeywell DR Graphic Bedienungsanleitung

Honeywell

Honeywell DR4500A Handbuch

Honeywell

Honeywell DR4500A Bedienungsanleitung

Honeywell

Honeywell X Series Bedienungsanleitung

Honeywell

Honeywell DR4300 Series Bedienungsanleitung

Honeywell

Honeywell ERX 350 Bedienungsanleitung

Beliebte Diktiergerät Handbücher anderer Marken

Sony

Sony ICD-UX533F Bedienungsanleitung

RCA

RCA VR5230 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Benutzerhandbuch

Sony

Sony TCM-400DV Bedienungsanleitung

LogTag

LogTag TREL30-16 Bedienungsanleitung

SVAT

SVAT CVP800 Bedienungsanleitung

Marantz

Marantz PMD620 Bedienungsanleitung

Zoom

Zoom H4next Bedienungsanleitung

Roland

Roland BR-900CD Bedienungsanleitung

JVC

JVC ProHD GY-HMZ1U Bedienungs- und Wartungshandbuch

Panasonic

Panasonic PQT8531-P Bedienungsanleitung

Sanyo

Sanyo TRC-6400 Bedienungsanleitung

Tascam

Tascam DR-07 Bedienungsanleitung

Olympus

Olympus DW-90 Bedienungsanleitung

Sanyo

Sanyo ICR-B150 Bedienungsanleitung

Korg

Korg D4 Bedienungsanleitung

Sony

Sony ICD-SX46 - Ic Recorder Bedienungsanleitung

Olympus

Olympus DIGITAL VOICE RECORDER WS-200S Montageanleitung