Honeywell OnCell 3150A-LTE-EU Bedienungsanleitung

➔

www.docuthek.com

D GB F NL I E Cert. version 09.18 · Edition 09.18 ·

Please read and keep in a safe place

Please read through these instructions

carefully before installing or operating. Following the

installation, pass the instructions on to the opera-

tor. This unit must be installed and commissioned

in accordance with the regulations and standards

in force. These instructions can also be found at

www.docuthek.com.

Explanation of symbols

• ,  ,  ,  ... = Action

▷= Instruction

Liability

We will not be held liable for damage resulting from

non-observance of the instructions and non-com-

pliant use.

Safety instructions

Information that is relevant for safety is indicated in

the instructions as follows:

DANGER

Indicates potentially fatal situations.

WARNING

Indicates possible danger to life and limb.

CAUTION

Indicates possible material damage.

All interventions may only be carried out by qualiﬁed

gas technicians. Electrical interventions may only be

carried out by qualiﬁed electricians.

Conversion, spare parts

All technical changes are prohibited. Only use OEM

spare parts.

32-00191-01

QUICK START GUIDE

Industrial Cellular Router

OnCell 50A-LTE-EU

Safety

Contents

Safety ................................. 1

Checking the usage ......................2

Configuration............................2

Installation ..............................3

Wiring .................................4

Specifications ........................... 7

Standards and Certifications ................8

Warranty ...............................8

32-00191-01

OnCell G3150A-LTE-EU · Edition 09.18 · GB

Checking the usage

The OnCell G3150A-LTE is a reliable, secure, LTE

gateway with state-of-the-art global LTE module. This

4G cellular gateway provides a more reliable connec-

tion to your Ethernet network for cellular applications.

To enhance industrial reliability, the OnCell G3150A-

LTE features isolated power inputs, which together

with high-level EMS and wide-temperature support

give the OnCell G3150A-LTE the highest level of de-

vice stability for any rugged environment. In addition,

with dual-SIM GuaranLink and dual power inputs, the

OnCell G3150A-LTE supports network redundancy

to ensure uninterrupted connectivity.

The OnCell G3150A-LTE also comes with a 3-in-1

serial port for serial over LTE cellular network com-

munication. Use the OnCell G3150A-LTE to collect

data and exchange data with serial/Ethernet devices.

Package Checklist

Moxa’s OnCell G3150A-LTE is shipped with the fol-

lowing items:

– 1 OnCell G3150A-LTE unit

– 2 2G/3G/4G antennas 2 dBi omni-directional with

SMA male connectors

– 1 DIN-rail mounting kit (mounted on OnCell)

– Quick installation guide (printed)

– Warranty card

▷

If any of these items is missing or damaged,

please contact your customer service repre-

sentative for assistance.

Panel Layout

GPS/GLONASS

SIM1

SIM2

RESET

Top Panel View

Front Panel View

Rear Panel View

Bottom Panel View

GPS/GLONASS

SIM1

SIM2

RESET

Top Panel View

Front Panel View

Rear Panel View

Bottom Panel View

GPS/GLONASS

SIM1

SIM2

RESET

Top Panel View

Front Panel View

Rear Panel View

Bottom Panel View

GPS antenna connector (female SMA)

Terminal block (top-down: PWR1 and PWR2,

1 digital relay and 2 digital inputs)

Grounding screw (M5)

42x2 MIMO antenna ports for LTE (female

SMA)

5RS-232 serial console (RJ45)

610/100 Base T(X) Ethernet port (RJ45)

7LED display

8DIN-rail mounting kit

9Reset button

0

Dual SIM–SIM1



Dual SIM–SIM2

Conﬁguration

▷

Before conﬁgurating the OnCell G3150A-LTE,

make sure that all items in the package checklist

are in the box.

▷In addition, you will need access to a notebook

computer or PC equipped with an Ethernet port.

▷

The OnCell G3150A-LTE has a default IP address

that you must use when connecting to the device

for the ﬁrst time.

Take the following steps to conﬁgure your OnCell

G3150A-LTE. For the location of the ports and sock-

ets, see page 2 (Checking the usage).

Step : Insert a SIM card and turn on the

OnCell G50A-LTE

 Use a screwdriver to loosen the screws and

remove the SIM card cover.

 Insert one or two 2G/3G/4G SIM cards (full-sized

SIM/1FF) into the SIM card slots located on the

bottom of the OnCell G3150A-LTE.

▷

If you are only using one SIM card, insert it in

the top slot (slot 1; the card in slot 1 is referred

to as SIM1).

▷By default, the SIM card in the slot 1 is treated

as the primary card. To change the default to

SIM2 (the card in slot 2), log in to the OnCell’s

web UI, and conﬁgure SIM2 as the primary card.

When the OnCell device is turned on, it boots up

based on the conﬁguration information stored

on the primary SIM card.

 Turn on the OnCell G3150A-LTE by connecting

a power terminal block to a DC power source

(12 to 48 VDC).

▷For details, see page 4 (Wiring).

4 Reattach the cover.

Step : Connect the OnCell G50A-LTE to a

notebook or PC

▷

Since the OnCell G3150A-LTE supports MDI/

MDI-X auto-sensing, you can use either a

straight-through cable or crossover cable to

connect the OnCell G3150A-LTE to a computer.

▷See the 10/100BaseT(X) Ethernet Port Connec-

tion section below for detailed instructions.

OnCell G3150A-LTE-EU · Edition 09.18 · GB

▷

If the LED indicator on the OnCell G3150A-LTE’s

LAN port lights up, it means a connection has

been established.

Step : Set up an IP address for the computer

4 Set an IP address on the same subnet as the

OnCell G3150A-LTE.

▷

Since the OnCell G3150A-LTE’s default IP ad-

dress is 192.168.127.254, and the subnet mask

is 255.255.255.0, you should set the IP address

of the computer to 192.168.127.xxx and subnet

mask to 255.255.255.0.

Step 4: Use the web-based manager to

conﬁgure the OnCell G50A-LTE

5 Open your computer’s web browser and type

http://192.168.127.254 in the address ﬁeld to

access the homepage of the web-based man-

agement system.

▷

Before the homepage opens, you will need to

enter the username and password.

6 For ﬁrst-time conﬁguration, enter the default

username and password given below:

Username: admin

Password: moxa

7 Click on the Login button.

ATTENTION

For security reasons, we strongly recommend

changing the password. To change the password,

select Maintenance ➜Username/Password, and

then follow the on-screen instructions.

▷You must either click the Save Conﬁguration or

the Restart button for the conﬁguration changes

to take effect.

Installation

WARNING

– This equipment is intended to be used in a Re-

stricted Access Location, such as a dedicated

computer room, where access can only be gained

by SERVICE PERSONS or by USERS who have

been instructed about the fact that the metal

chassis of the equipment is extremely hot and

may cause burns.

– Service persons or users should pay special atten-

tion and take special precautions before handling

this equipment.

– Only authorized, well-trained professionals should

be allowed to access the restricted access loca-

tion. Access should be controlled by the authority

responsible for the location with lock and key or

a security identity system.

– External metal parts are hot!! Pay special at-

tention or use special protection before handling

this equipment.

ATTENTION

– The OnCell G3150A-LTE is NOT a portable mobile

device and should be located at least 20 cm away

from the human body.

– The OnCell G3150A-LTE is NOT designed for

the general public. A well-trained technician is

required to deploy the OnCell G3150A-LTE units

and safely establish a wireless network.

– For EXPLOSION-PROOF applications, the OnCell

G3150A-LTE is designed and certiﬁed to meet

ATEX and IECEx requirements. You should mount

the device in a suitable enclosure rated at least

IP54, in accordance with IEC/EN 60079-15 stand

ard, so that it is accessible only by the use of a

tool. The device is not intended for use in an area

with pollution degree rating > 2 in accordance

with EN 60664-1.

– When you install the OnCell G3150A-LTE in an

enclosure, the antennas must also be installed

in such a way that they are inside the enclosure.

External antenna deployment is allowed only if

the antennas are certiﬁed for ATEX Zone 2 use

or conﬁrm to IECEx standards.

DIN-Rail Mounting

▷DIN-Rail Kit Dimensions:

Unit = mm (inch)

48.4

(1.91)

15.0

(0.59)

22.7

(0.89)

12.5 (0.49)

25.0 (0.98)

▷The OnCell G3150A-LTE comes with a DIN-rail

kit attached to the back panel.

▷

Mount the OnCell G3150A-LTE on corrosion-free

mounting rails that meet the EN 60715 standard.

 Insert the upper lip of the DIN rail into the top

hook of the DIN-rail mounting kit :

OnCell G3150A-LTE-EU · Edition 09.18 · GB

 Press the OnCell G3150A-LTE towards the DIN

rail until it snaps into place:

▷

To remove the OnCell G3150A-LTE from the DIN

rail, reverse steps and above.

Wall Mounting (optional)

▷Wall-Mounting Kit Dimensions:

Unit = mm (inch)

67.0 (2.64)

36.0 (1.42)

20.0

(0.79)

6.0 (0.24)

10.0

(0.39) 20.0

(0.79)

8.0

(0.32)

▷For some applications, it may be more conveni-

ent to mount the OnCell G3150A-LTE to a wall:

 Remove the aluminum DIN-rail attachment plate

from the OnCell G3150A-LTE

 Then attach the wall-mounting plates with M3

screws.

▷Mounting the OnCell G3150A-LTE to a wall re-

quires 4 screws.

 Use the OnCell G3150A-LTE device, with wall

mount plates attached as a guide, to mark the

correct locations of the 4 screws.

▷

The heads of the screws should be less than 6.0

mm in diameter, and the shafts should be less

than 3.5 mm in diameter.

< 6 mm

< 3.5 mm

▷

Test the screw head and shank size by insert

ing the screws into one of the keyhole shaped

apertures of the wall-mounting plates before

attaching the plates to the wall.

4 Once the screws are ﬁxed into the wall, insert

the four screw heads through the large opening

of the keyhole-shaped apertures.

5 Then slide the OnCell G3150A-LTE downwards.

6 Tighten the four screws for added stability.

Wiring

WARNING

Safety First!

Be sure to disconnect the power cord before install-

ing and/or wiring your Moxa OnCell G3150A-LTE.

EXPLOSION HAZARD!

Do not disconnect equipment unless you have

removed the power source to the equipment or

the area is known to be non-hazardous.

▷

Use separate paths to route wiring for power

and devices.

▷

If power wiring and device wiring paths must

cross, make sure the wires are perpendicular

at the intersection point.

▷

Do not run signal or communications wiring and

power wiring in the same wire conduit. To avoid

interference, wires with different signal charac-

teristics should be routed separately.

OnCell G3150A-LTE-EU · Edition 09.18 · GB

▷

You can use the type of signal transmitted

through a wire to determine which wires should

be kept separate. The rule of thumb is that wir-

ing with similar electrical characteristics can be

bundled together.

▷Keep input wiring and output wiring separate.

▷It is strongly advised that you label wiring to all

devices in the system when necessary.

ATTENTION

– This product is intended to be supplied by a Listed

Power Unit marked “Class 2” or “LPS” and rated

O/P: 9.6 W (12 V/0.78 A to 48 V/0.2 A).

– Make sure that the external power adapter (in-

cludes power cords and plug assemblies) pro-

vided with the unit is certiﬁed and suitable for use

in your country.

– Use the antennas correctly!

Wide-band (2G/3G/4G) antennas are needed

when the OnCell G3150A-LTE operates. Make

sure that your antenna installation is within a safety

area, which is covered by a lightning protection

or surge arrest system.

WARNING

Do not locate the antenna near overhead power

lines or other electric light or power circuits, or

where it can come into contact with such circuits.

When installing the antenna, take extreme care not

to come into contact with such circuits, because

they may cause serious injury or death when there

is a surge. For instructions on proper installation

and grounding of the antenna, refer to national and

local codes (for example, U.S.: NFPA 70, National

Electrical Code, Article 810, and Canada: Canadian

Electrical Code, Section 54).

Grounding the Moxa OnCell G50A-LTE

▷

Grounding and wire routing help limit the ef-

fects of noise due to electromagnetic interfer-

ence (EMI). Run the ground connection from the

ground screw to the grounding surface prior to

connecting devices.

▷

The minimum cross-sectional area of the ground-

ing conductor should be equal to that of the

input cable.

ATTENTION

This product is intended to be mounted on a well-

grounded mounting surface, such as a metal panel.

The potential difference between the two ground

potentials must be zero. If the potential difference

is NOT zero, the product could be permanently

damaged.

Connecting the Power Input

▷

Input Terminal Block (J3) is suitable for 12-28

AWG (3.31-0.0804 mm2) wire size, torque value

4.5 lb-in (0.51 Nm).

Pinouts for the Power Inputs and Relay

Output

V1+

V1-

V2+

V2-

COM 1

COM 2

Pin Name Usage

1V1+ DC Power Input 1

2V1-

3V2+ DC Power Input 2

4V2-

5Relay Output

7I1 Digital Input

8COM 1 Digital Input GND

9I2 Digital Input

10 COM 2 Digital Input GND

Wiring the Redundant Power Inputs

ATTENTION

Before connecting the OnCell G3150A-LTE to the

DC power inputs, make sure that the DC power

source voltage is stable.

▷The top two pairs of contacts of the 10-contact

terminal block connector located on the top

panel of the OnCell G3150A-LTE are used as

the two DC inputs.

V1+

V1-

V2+

V2-

V1+

V1-

V2+

V2-

Top

Front

 Insert the negative/positive DC wires into the V-/

V+ terminals.

 To keep the DC wires from pulling loose, use a

small ﬂat-blade screwdriver to tighten the wire-

clamp screws on the front of the terminal block

connector.

 Insert the plastic terminal block connector prongs

into the terminal block receptor, which is located

on the top panel of the OnCell G3150A-LTE.

Wiring the Relay Contact

▷

The OnCell G3150A-LTE has one relay output,

which consists of the two contacts of the terminal

block on the OnCell G3150A-LTE’s top panel.

▷

For detailed electrical requirement, see page

7 (Speciﬁcations).

OnCell G3150A-LTE-EU · Edition 09.18 · GB

▷

The relay contacts are used to indicate user-

conﬁgured events. The two wires attached to

the relay contacts form an open circuit when

a user-conﬁgured event is triggered. If a user-

conﬁgured event does not occur, the relay circuit

will be closed.

Wiring the Digital Inputs

▷The OnCell G3150A-LTE has two sets of digital

inputs—DI1 and DI2.

▷

Each DI comprises of two contacts on the 6-pin

terminal block connector located on the top

panel of the OnCell G3150A-LTE.

▷For detailed information on isolated digital input

deﬁnition, see page 7 (Speciﬁcations).

Communication Connections

0/00BaseT(X) Ethernet Port Connection

▷The 10/100BaseT(X) ports located on the front

panel of the OnCell G3150A-LTE are used to

connect to Ethernet-enabled devices.

▷

Pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports:

MDI Port

Pinouts

MDI-X Port

Pinouts 8-Pin RJ45

Pin Signal Pin Signal

1Tx+ 1Rx+

1 2 3 4 5 6 7 8

2Tx- 2Rx-

3Rx+ 3Tx+

4Rx- 6Tx-

Serial DB9 Connection

▷

The OnCell G3150A-LTE has one DB9 male port

that supports RS-232, RS-485-4W, RS-485-2W,

and RS-422:

Pin assignments DB9 Male

Connector

Pin RS- RS-4/

485-4w

RS-

485-w

1DCD TxD-(A) –

1 5

6 9

2RxD TxD+(B) –

3TxD RxD+(B) Data+(B)

4DTR RxD-(B) Data-(A)

5GND GND GND

6DSR

7TRS

8CTS

9 – – Tx-

RS- Console Connection

▷

The OnCell G3150A-LTE has one RS-232 (8-pin

RJ45) console port located on the front panel.

▷

Use either an RJ45-to-DB9 or RJ45-to-DB25

cable to connect the Moxa OnCell G3150A-LTE’s

console port to your PC’s COM port.

▷

You may then use a console terminal program to

access the OnCell G3150A-LTE for conﬁguring

the console conﬁguration.

Console Pinouts for 0-Pin or 8-Pin RJ45

0-Pin Description 8-Pin

1 –

1 2 3 4 5 6 7 8

2DSR 1

3RTS 2

4GND 3

5TxD 4

6RxD 5

7 – 6

8CTS 7

9DTR 8

10 –

▷

The pin numbers for both 8-pin and 10-pin RJ45

connectors (and ports) are typically not labeled

on the connector (or port).

LED Indicators

▷

The front panel of the Moxa OnCell G3150A-LTE

contains several LED indicators.

Function of LEDs

Type Color State Description

Signal

(1 LED)

Green Blinking

The number of blinks indicates

the cellular signal level (once the

device is connected to a cellular

network with an IP address.)

Interval between two blinks:

200 ms

Gap: 2 seconds

No. of

Blinks

Cellular

RSSI

RSSI Ran-

ge (dBm)

10 < SNR

≤ 12

113 <

RSSI ≤

-89

12 <

SNR ≤

-89 < RSSI

≤ -73

22 <

SNR ≤

-73 < RSSI

≤ -51

The Cellular RSSI value is based

on the OnCell device signal

strength returned by the AT+

CSQ AT command. You can

also refer to the equivalent signal

RSSI Range (dBm) provided in

the table above.

PWR1/

PWR2

Green On DC power source active

Off Power is off

Ready Green On

System startup is complete and

the system is in operation

Blinking

(slow at

1-sec

intervals)

The OnCell device has been lo-

cated by the

Wireless Search Utility.

Off

Power is off, or device is boo-

ting up.

Fault Red On

Device is booting up, or IP

address conﬂict.

Blinking

(slow at

1-sec

intervals)

Cannot get an IP address from

the DHCP

server

Off

Power is off or no error condition

exists.

OnCell G3150A-LTE-EU · Edition 09.18 · GB

Function of LEDs

Type Color State Description

2G/3G Amber Blinking

(slow at

500-ms

intervals)

GSM/GPRS/EDGE is connected.

On UMTS/HSPA is connected.

Off GSM/GPRS/EDGE/UMTS/

HSPA is

disconnected.

4G Amber On LTE is connected

Off LTE is disconnected.

SIM1 Amber On/Off SIM 1 is active or inactive

Blinking

SIM 1 is not inserted or PIN code

is incorrect

SIM2 Amber On/Off SIM 2 is active or inactive

Blinking

SIM 2 is not inserted or PIN code

is incorrect

GPS Green On GPS signal has been located

Blinking Locating GPS signal or

less than four satellites have

been located.

Off

GPS signal has not been located

TX Rx Amber On

The serial port is transmitting

data

Off No data is being transmitted or

received

through the serial port

Speciﬁcations

Cellular Speciﬁcation

Standards: GSM/GPRS/EDGE/UMTS/HSPA/LTE.

Band Options:

OnCell G3150A-LTE-EU:

B1 (2100 MHz)/B3 (1800 MHz)/B7 (2600 MHz)/B8

(900 MHz)/B20 (800 MHz),

UMTS/HSPA 2100/1900/850/800/900 MHz,

OnCell G3150A-LTE-US:

B2 (1900 MHz)/B4 (AWS)/B5 (850 MHz)/ B13 (700

MHz)/B17 (700 MHz)/B25 (1900 MHz),

UMTS/HSPA 2100/1900/AWS/850/900 MHz,

Universal quad-band GSM/GPRS/EDGE/1800/1900

MHz.

LTE Data Rate:

Category 3 Downlink: 100 Mbps (20 MHz bandwidth),

50 Mbps (10 MHz bandwidth) Uplink: 50 Mbps (20

MHz bandwidth), 25 Mbps (10 MHz bandwidth).

HSPA Data Rate:

Downlink: Up to 42 Mbps (category 24) Uplink: Up

to 5.76 Mbps (category 6).

GPRS Data Rate:

Downlink/Uplink: 85.6 kbps DL, 42.8 kbps UL.

Interface

Cellular Antenna Connectors:

2 SMA (female), MIMO for LTE, antenna diversity

for WCDMA.

SIM Slots: Dual SIM card support, full-sized SIM (1FF).

GNSS:

1 SMA (female), GPS: 1575.42 MHz, GLONASS:

1602 MHz.

Ethernet:

1, 10/100 Mbps auto negotiation speed, F/H duplex

mode and auto MDI/MDI-X connection (RJ45-type).

Serial Console Port:

1, RS-232 (RJ45-type).

Serial Port:

1, RS-232, RS-485-4W , RS-485-2W, RS-422 (DB9

male).

Serial Communication Parameters:

Data Bits: 5,6,7,8,

Stop Bits: 1,1.5, 2 (when parity = None),

Parity: None, Even, Odd, Space, Mark,

Baudrate: 75 bps to 921.6 kbps.

LED Indicators:

PWR1, PWR2, READY, FAULT, CELLULAR SIGNAL,

SIM1, SIM2, 2G/3G, 4G, GPS, TX/RX.

Alarm Contact: 1 relay output with current carrying

capacity of 1 A @ 24 VDC.

Digital Inputs:

2 electrically isolated inputs:

+13 to +30 V for state “1”,

+3 to -30 V for state “0”,

Max. input current: 8 mA.

Ground Screw: M5.

Reset Button: Power reset/factory default reset.

Software Speciﬁcation

Network Protocol:

ICMP, TCP/IP, UDP, DHCP, Telnet, DNS, SNMP, HTTP,

HTTPS, SMTP, SNTP, ARP.

Routing/Firewall:

NAT, port forwarding, IP/MAC/port ﬁltering.

VPN:

Max. Tunnel Number: 5 (Responder/Initiator)

IPsec (DES, 3DES, AES, MD5, SHA-1, DH2, DH5),

PSK/X.509/RSA,

GRE over IPsec,

Open VPN,

NAT-T, PFS, DPD.

Management Options:

Remote SMS Control, SNMPv1/v2c/v3, Web/Telnet/

Serial Console.

Others: DDNS.

Software Speciﬁcations (Moxa Proprietary)

GuaranLink: Dual SIM 4-tiers heart-beat for reliable

and persistent cellular connectivity.

OnCell Central Manager: Large scale centralized de-

vice management over private cellular IP addresses.

Search Utility:

Simple device conﬁguration and management utility.

Physical Characteristics

Housing: Aluminum, providing IP30 protection.

Mounting:

DIN rail (default) or wall mount (optional).

Input Terminal Block (J3):

Suitable for 12-28 AWG (3.31-0.0804 mm2) wire size,

torque value 4.5 lb-in (0.51 Nm). The minimum cross-

sectional area of the grounding conductor should be

equal to that of the input cable.

Weight: 492 g (1.08 lb).

OnCell G3150A-LTE-EU · Edition 09.18 · GB

For More Information

The Honeywell Thermal Solutions family of products includes

Honeywell Combustion Safety, Eclipse, Exothermics, Hauck,

Kromschröder and Maxon. To learn more about our products, visit

www.ThermalSolutions.honeywell.com or contact your Honeywell

Sales Engineer.

Elster GmbH

Strotheweg 1, D-49504 Lotte

T +49 541 1214-0

[email protected], www.kromschroeder.de

Elster is part of Honeywell

Honeywell Thermal Solutions – Support Line

T ++1 888-516-9282

[email protected]

Original operating manual

Dimensions:

141.8

(5.58)

126.0

(4.96)

107.5

(4.23)

117.9

(4.64)

30.0

(1.18)

Installation:

DIN-rail mounting, wall mounting (with optional kit).

Environmental Limits

Operating Temperature:

Standard Models: 0 to 55°C (32 to 131°F),

Wide Temp. Models: -30 to 70°C (-22 to 158°F).

Storage Temperature: -40 to 85°C (-40 to 185°F).

Ambient Relative Humidity:

5 to 95% (30°C, non-condensing).

Power Requirements

Input Voltage:

12 to 48 VDC, redundant dual DC power inputs.

Connector: 4-pin removable terminal block.

Power Consumption:

9.6 W (12 V/0.78 A to 48 V/0.2 A).

Reverse Polarity Protection: Present.

Reliability

MTBF: > 528,596 hours.

Standards and Certiﬁcations

Safety

OnCell G3150A-LTE-US: UL 60950-1.

EMI

OnCell G3150A-LTE-US: FCC Part 15 Subpart B.

EMS

OnCell G3150A-LTE-EU: EN 61000-6-2/-4.

Radio

OnCell G3150A-LTE-US:

FCC ID N7NMC7355,

OnCell G3150A-LTE-EU:

EN 301 489-1, EN 301 489-7, EN 301 511/4.

ATEX Zone  Certiﬁcation Information

Demko 16 ATEX 1812X,

II 3 G Ex nA IIC T5 Gc,

Ambient Range:

-30°C ≤Tamb ≤ +70°C.

IECEx UL 16.0166X

Hazardous Location Standards

EN 60079-0:2012+A11:2013 / IEC 60079-0

6th Edition,

EN 60079-15: 2010 / IEC 60079-15 4th Edition.

ATTENTION

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference re-

ceived, including interference that may cause un-

desired operation.

Warranty

Warranty Period: 5 years.

Details:

See www.moxa.com/support/warranty.aspx.

Inhaltsverzeichnis

Andere Honeywell WLAN-Router Handbücher

Honeywell

Honeywell 315-508 Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung

Draytek

Draytek Vigor2120 Series Bedienungsanleitung

Sitecom

Sitecom WLR-4000 Bedienungsanleitung