Hornady Security RAPiD SAFE Bedienungsanleitung

Item No. 98150

586064 11/2014

Owner’s Manual

RAPiD®

SAFE

Fold out for mounting template

This is a California-approved rearms safety device

that meets the requirements of California Penal

Code Section 12088 and the regulations issued

thereunder.

This product has been tested and certied to conform to ASTM

F2456, Youth Resistant Firearms Container.

P.O. Box 1848, Grand Island, Nebraska 68802-1848

308-382-1390 • 800-338-3220 • Fax: 308-382-5761

www.hornady.com • Hornady.com/contact_us

ALIGN TEMPLATE WITH FRONT KEYPAD EDGE

Align corner

of template to

the front right

corner of safe.

Important Information

• RFID Tag refers to the chip in any of the RFID “keys” included with the

RAPiD®safe (bracelets, key fob or card).

• For trouble-free operation of your RAPiD®safe, please read and understand

all instructions before use.

• Questions? Call our tech line at 800-338-3220.

• Never store loaded ﬁrearms in the RAPiD®safe. Follow local laws for

ﬁrearm storage.

READ THIS FIRST

Warning: NEVER store a loaded ﬁrearm in the Hornady®Security™RAPiD®

safe under any circumstances. The risks associated with storage of a loaded

ﬁrearm include, but are not limited to, unintentional discharge upon insertion

or removal of the ﬁrearm. Unintentional discharge may result in bullet and safe

fragments dispersing in multiple directions, which may cause serious injury or

death. Hornady®Security™is not liable for any misuse of the RAPiD®safe.

Warning: No safe is entirely secure. The RAPiD®safe is only as secure as your

maintenance of the combination code, keys, and RFID tags. You are solely

responsible for maintaining your combination code, keys, and RFID tags. Never

write down your combination code. Keep your keys and RFID tags in a secure

location at all times. Store your RAPiD®safe in a secure location away from

your keys and RFID tags. Hornady®Security™is not liable for unauthorized

access, including damage to, or loss of property, or personal injury. Again,

NEVER store a loaded ﬁrearm in your Hornady®RAPiD®safe, as this may result

in unauthorized access to the loaded ﬁrearm.

Warning: Except as expressly provided in the RAPiD®Safe Limited Warranty,

Hornady®Security™is not liable for any expense or damage associated with

your inability to open the RAPiD®safe. Electronic systems may fail. Verify that

the keys furnished operate the lock. Keep your keys in a secure location at all

times. For your security, Hornady®Security™WILL NOT send replacement keys.

Warning: Hornady®Security™is not liable for any loss, theft, or damage to

personal property. The RAPiD®safe is not intended to protect the contents

from ﬁre, water, humidity, or other environmental conditions. Do not, under

any circumstances, return the RAPiD®safe to Hornady®Security™with any

personal property inside.

Mounting Template

Exterior: 15½"x9"x3½"

Interior: 11"x8"x3"

Weight: 15.65 lbs

Power: 12V 1.0A

Table of Contents

Warnings and Important Information....................................................... Page 2

Items Included.......................................................................................... Page 3

Setup and Operation ................................................................................. Page 4

Warranty.................................................................................................... Page 9

Product Registration and Service ............................................................ Page 10

Frequently Asked Questions ..................................................................... Page 10

Mounting Template.................................................................................... Page 11

Items included with your RAPiD®Safe

1. RAPiD®Safe

2. Wall Power Supply (including 220 Volt Adapter for European Usage)

3. Three (3) RFID Bracelet Tags (One of each size: M, L, XL)

4. One (1) RFID Card Tag

5. One (1) RFID Key Fob Tag

6. Two (2) Circular (Barrel) Keys

7. Security Cable

Not Pictured:

• Owner’s Manual

• Warranty Card

• Hornady®Decal Magnet

Program Buttons

Latch in Home

Position

RAPiD®Safe Setup and Operation

Congratulations on purchasing the technologically advanced RAPiD®safe. You have taken a

signiﬁcant step in securing the safety of your handgun.

To achieve the best experience with your RAPiD®safe, please read all instructions carefully,

and understand its operation.

After the RAPiD®safe has been taken out of the box, please check to be sure the circular

(barrel) key ﬁts and unlocks your RAPiD®safe (See page 7 for Manual Lock information).

Contact Hornady®at 800-338-3220 if the key does not work.

Combination Code

Your safe’s factory preset combination code is 1-2-3-4-ENTER.

Opening and Closing RAPiD®Safe

Open your safe by plugging the unit into an

electrical outlet. Enter the factory preset

code: 1-2-3-4-ENTER.

Close the safe by pressing the lid down until

its bolts are engaged.

NOTE: NEVER close the safe until the latch

motor has returned to home position.

Changing the Combination Code

To create a new 4, 5, or 6 digit code:

1. Open your RAPiD®safe.

2. Locate the three small program buttons

on its inside right corner.

3. Press the top white button.

4. When the amber status light on the front

keypad blinks, the system is ready to

receive your code.

5. Key in your preferred 4 to 6 digit code,

and press ENTER.

6. The keypad will blink twice, indicating your code has been correctly saved.

7. WITH THE LID OPEN, test the code. If the motor does not run, repeat steps 2 through 7.

NOTE: Keypad is equipped with an anti-tamper feature that disables the keypad for

2 minutes upon 5 consecutive incorrect keypad code entries. This feature does not disable

normal opening function using RFID Tag.

Choose the two RFID entry methods (tags)

you prefer, and program them for use.

Program Buttons

RFID Tags

Your RAPiD®safe includes ﬁve (5) different

RFID tags, including:

• 3 Bracelets (M, L, XL)

• 1 Key Fob

• 1 Card

The safe’s system can only store up to two (2)

different tags at a time. Only two tags can be

programmed for use. The remaining three tags

will be inert, but can be circulated as one of

the programmed tags if you choose to use

them later, i.e., you can program two bracelets,

or one bracelet and the card, but no more than

two tags may be programmed for use at any

given time.

How To Change Your RFID Tags

The RAPiD®safe can store up to 2 tags.

To program these tags:

1. Open your RAPiD®safe.

2. Locate the three small program buttons on

the inside right corner.

3. Press the middle (black) button to program

your FIRST RFID tag. Choose one of the ﬁve

tags listed above.

4. When the amber status light on the keypad

blinks, the system is ready for your RFID tag.

5. Place the RFID tag approximately 1/2" over

the RFID reader (H logo) that is located on

the front panel of the safe.

6. Wait for the status light to display green.

7. Remove the tag from the RFID reader on the

front panel of the safe.

8. WITH THE LID OPEN, test the tag by placing

it approximately 1/2" over the RFID reader. If

you do not hear and see the motor activate,

repeat steps 2 through 8.

9. The second RFID tag can be programmed

by pushing the third, lowest (black) button

inside the box and following the steps above.

On/Off Switch

Backlit Reader

Battery Power Mode

When the RAPiD®safe is unplugged, and is operating on battery power, you must press

the ENTER key to activate system.

Pressing the ENTER key causes the system to achieve ready status. This includes RFID tag

reading and keypad operation.

For example: To open your safe with an RFID tag, while the system is running on

battery power, ﬁrst press the ENTER key to bring it to ready status. Place your RFID tag

approximately 1/2" over the RFID reader to open the safe.

To open your safe with your keypad code, ﬁrst press the ENTER key to bring it to ready

status. Enter your code on the keypad followed by ENTER, to open the safe.

Backlit Reader

Your safe’s backlit reader remains on

while the system is plugged into an

electrical outlet, unless you switch it off.

The backlit reader will switch off when the

system times out for 20 seconds under

battery power only.

To turn the light off (when using electrical

power), open the safe, and locate the

on/off switch next to the white program

button.

Keypad Status Light Codes

When the light

displays: It means:

Solid Red The system is

powered and ready.

Blinking Amber The system is ready to

program.

Solid Amber

The battery is low.

Replace batteries

immediately.

Solid Green The system is

unlocking.

Manual Lock

Side-Locking Tab

Status Light

Manual Lock

The mechanical key lock is located under the keypad panel. To manually unlock the RAPiD®

safe, carefully remove the keypad panel by pushing the locking tab toward the “H” and then

lifting up, carefully protecting the attached wires. Press the safe lid down while turning the

key to unlock the unit.

Left-Hand/Right-Hand

Feature

To reverse the keypad panel for opposite

hand usage, press the side-locking tab

and reverse the keypad panel, carefully

protecting the attached wires.

Batteries

For backup or mobile use, your safe requires

eight AA batteries (not included). To install

or replace batteries, carefully remove the

keypad panel and battery case cover. Only

use new alkaline AA batteries. Verify the

battery pack is plugged in. Replace all

batteries at the same time.

NOTE: The RAPiD®safe is not designed to

operate on a 9V battery.

NOTE: Solid Amber status light indicates

low battery. Batteries should be replaced

immediately.

NOTE: Replace batteries every 12 months.

Cable

Locked Lever

Unlocked Lever

RAPiD

Sleeve

RAPiD

Safe

without Sleeve

Security Cable

The RAPiD®safe includes a security cable, that

can be looped around a stationary object. With the

safe cover open, place the lug end of the cable

into the security cable slot and close the lid.

Removing & Reinstalling

the RAPiD®Sleeve

The RAPiD®sleeve accommodates most

5-inch pistols, and 4-inch barreled

revolvers. Removing the RAPiD®sleeve can

accommodate larger handguns or other

valuables.

To remove the sleeve, lift the levers located

on each side of the sleeve, and pull it out.

Reinstalling the sleeve is just as simple.

Make sure the levers are up and push the

sleeve in place, aligning the notches with

the bar. Press the levers down to lock the

sleeve in place. Remove and reinstall the

sleeve a few times to become familiar

with the process.

RAPiD®Safe Limited Warranty

Hornady®Security™warrants the RAPiD®safe will, in normal use and service, be free from

defects in workmanship or materials for one (1) year from date of purchase.

This Limited Warranty does not cover any of the following:

(a) Damage, deterioration, or malfunction resulting from accident, negligence,

misuse, improper installation, or lack of maintenance;

(b) Any defects not discovered and reported to Hornady®Security™during the

one (1) year warranty period;

This Limited Warranty is not transferable and is enforceable by the original owner only. In

the event that Hornady®Security™receives notice from the original purchase of a warranty

claim in conformity herewith, Hornady®Security™will promptly undertake an investigation

of such claim. If the warranty claim is covered by the Limited Warranty, Hornady®Security,

™

will, in its sole discretion, repair the defect(s) or replace RAPiD®safe at the expense of

Hornady®Security.

™

Disclaimer of Implied Warranties. EXCEPT AS IS OTHERWISE EXPRESSLY SET

FORTH IN THE ABOVE LIMITED WARRANTY, HORNADY®SECURITY™MAKES NO OTHER

REPRESENTATIONS OR WARRANTIES OF ANY KIND, WHETHER EXPRESSED OR IMPLIED,

BY OPERATION OF LAW OR OTHERWISE WITH RESPECT TO THE RAPiD®SAFE OR ANY

COMPONENT PART THEREOF, INCLUDING WITHOUT LIMITATION ANY REPRESENTATION

OR WARRANTY WITH RESPECT TO MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR

PURPOSE OR USE.

Limitation on Liability. THE OBLIGATION OF HORNADY®SECURITY™TO REPAIR OR

REPLACE AS PROVIDED ABOVE SHALL BE THE SOLE AND ONLY REMEDY RESPECTING ANY

DEFECT IN THE RAPiD®SAFE, OR ANY COMPONENT PART THEREOF. IN THE EVENT THAT

THE FOREGOING REMEDY FAILS OF ITS ESSENTIAL PURPOSE, THE LIABILITY OF HORNADY®

SECURITY™TO PURCHASER SHALL NOT, IN ANY EVENT, EXCEED THE ACTUAL PURCHASE

PRICE OF THE NON-CONFORMING GOODS; AND

Limitation on the Nature of Damages. HORNADY®SECURITY™SHALL NOT, UNDER ANY

CIRCUMSTANCES, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,

INDIRECT, INCIDENTAL, CONSEQUENTIAL, LIQUIDATED OR PUNITIVE DAMAGES OF ANY

NAME, NATURE OR DESCRIPTION. HORNADY®SECURITY™IS NOT RESPONSIBLE FOR

DAMAGE TO OR THEFT OF THE RAPiD®SAFE, OR ITS CONTENTS.

Product Registration and Service

You must register your RAPiD®safe in order to obtain Warranty Service. Simply complete

and return the enclosed product registration card or submit through our website by going to

hornady.com/warranties

To Receive Warranty Service

In order to report a warranty claim, call Hornady®Security™at 800-338-3220 to request a

return authorization number. Returns will not be accepted without prior return authorization

by Hornady®Security.™When a return authorization number has been obtained, be sure all

contents have been removed from the RAPiD®safe before sending it for service. Hornady®

Security™is not liable for any loss, theft, or damage to personal property.

Post-Warranty Service Information

For issues concerning service after the Limited Warranty expires, contact Hornady®Security™

at 800-338-3220.

Frequently Asked Questions

I’ve lost my keys. Can I get a replacement?

For security reasons, Hornady®WILL NOT provide replacement barrel keys for the RAPiD®safe.

Consult a locksmith if needed.

Where can I ﬁnd the serial number?

The serial number is located under the keypad panel.

How long does my access code need to be?

Your code must be 4-to-6 digits long.

How long should the batteries last?

Quality batteries should last approximately 12 months, depending on use.

What size handgun will the RAPiD®safe accommodate?

The RAPiD®sleeve accommodates most 5-inch pistols, and 4-inch barreled revolvers.

Removing the RAPiD®sleeve allows more space for larger handguns.

How do I return my RAPiD® safe for warranty work?

Call Hornady®at 800-338-3220 and one of our technicians will assist you.

Why isn’t my RFID tag (bracelet, key fob, card) opening the safe?

• Be sure the RFID tag is programmed to your safe. The RAPiD®safe allows two (2)

RFID tags to be programmed for use.

• Check the power source. If the unit is plugged into an electrical outlet, the red

LED light should be on. If the unit is on battery power, press any keypad button

(to bring the system to ready) before placing the RFID tag on the reader.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hornady Security Sicher Handbücher

Hornady Security

Hornady Security 95432 Bedienungsanleitung

Hornady Security

Hornady Security BIOMETRiC SAFE 98110 Bedienungsanleitung

Hornady Security

Hornady Security TriPoint 98152 Bedienungsanleitung

Hornady Security

Hornady Security RAPID 97436 Bedienungsanleitung

Hornady Security

Hornady Security 95407 Bedienungsanleitung

Hornady Security

Hornady Security TRIPOINT LOCK BOX Bedienungsanleitung

Beliebte Sicher Handbücher anderer Marken

Squire

Squire Stronghold Keysafe Bedienungsanleitung

Phoenix

Phoenix FS0352C Produktinformationsblatt

Phoenix

Phoenix KS0030E Series Bedienungsanleitung

Vaultek

Vaultek 10 Series Technisches Datenblatt

Arregui

Arregui CLASS Bedienungsanleitung

Beaumont

Beaumont SMART KEYBOX Bedienungsanleitung

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Bedienungsanleitung

Hornady

Hornady SnapSafe Trunk Safe II Bedienungsanleitung

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Bedienungsanleitung

Honeywell

Honeywell 5912 Bedienungsanleitung

Phoenix

Phoenix FS1280F Bedienungsanleitung

Phoenix

Phoenix SS0992K Produktinformationsblatt

Technomax

Technomax Trony Series Handbuch

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Bedienungsanleitung

RICHTER CZECH

RICHTER CZECH LA Bedienungsanleitung

Olymp

Olymp GOsafe 110 Bedienungsanleitung

Phoenix

Phoenix SS0100E Produktinformationsblatt

Clarke

Clarke Strong-Arm CS1000K Bedienungsanleitung