MAN0925-01-EN Specifications / Installation
________________________________________________________________________________________________________________________________________
2/3/2010 Page 5 of 5 # 1018
5. Safety
When found on the product, the following symbols specify:
Warning: Electrical
Shock Hazard. Warning: Consult
user documentation.
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D
or Non-hazardous locations only
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless
power has been switched off or the area is known to be non-hazardous.
AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTOR
L'EQUIPMENT, COUPER LE COURANT OU S'ASSURER QUE
L'EMPLACEMENT EST DESIGNE NON DANGEREUX.
WARNING: To avoid the risk of electric shock or burns, always connect the
safety (or earth) ground before making any other connections.
WARNING: To reduce the risk of fire, electrical shock, or physical injury it is
strongly recommended to fuse the voltage measurement inputs. Be sure to
locate fuses as close to the source as possible.
WARNING: Replace fuse with the same type and rating to provide protection
against risk of fire and shock hazards.
WARNING: In the event of repeated failure, do not replace the fuse again as a
repeated failure indicates a defective condition that will not clear by replacing
the fuse.
WARNING – EXPLOSION HAZARD – Substitution of components may impair
suitability for Class I, Division 2
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE
COMPOSANTS PEUT RENDRE CE MATERIAL INACCEPTABLE POUR LES
EMPLACEMENTS DE CLASSE 1, DIVISION 2
WARNING - The USB parts are for operational maintenance only. Do not leave
permanently connected unless area is known to be non-hazardous.
WARNING – EXPLOSION HAZARD - BATTERIES MUST ONLY BE
CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS
AVERTISSEMENT - RISQUE D'EXPLOSION - AFIN D'EVITER TOUT
RISQUE D'EXPLOSION, S'ASSURER QUE L'EMPLACEMENT EST DESIGNE
NON DANGEREUX AVANT DE CHANGER LA BATTERIE
WARNING - Battery May Explode If Mistreated. Do Not Recharge, Disassemble
or Dispose Of In Fire
WARNING: Only qualified electrical personnel familiar with the construction
and operation of this equipment and the hazards involved should install, adjust,
operate, or service this equipment. Read and understand this manual and other
applicable manuals in their entirety before proceeding. Failure to observe this
precaution could result in severe bodily injury or loss of life.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Radiated Emission Compliance: For compliance requirement, a ferrite
(Horner P/N FBD006 supplied with the unit) needs to be placed on the AC/DC
line with one loop.
All applicable codes and standards need to be followed in the installation of this
product.
Adhere to the following safety precautions whenever any type of connection is
made to the module:
Connect the safety (earth) ground on the power connector first before making
any other connections.
When connecting to electric circuits or pulse-initiating equipment, open their
related breakers.
Do not make connections to live power lines.
Make connections to the module first; then connect to the circuit to be
monitored.
Route power wires in a safe manner in accordance with good practice and local
codes.
Wear proper personal protective equipment including safety glasses and
insulated gloves when making connections to power circuits.
Ensure hands, shoes, and floors are dry before making any connection to a
power line.
Make sure the unit is turned OFF before making connection to terminals.
Make sure all circuits are de-energized before making connections.
Before each use, inspect all cables for breaks or cracks in the insulation.
Replace immediately if defective.
•Use Copper Conductors in Field Wiring Only, 60/75°C
For assistance and Manual updates, contact Technical Support at the following
locations:
North America:
Tel: 317-916-4274
Fax: 317-639-4279
Web: www.heapg.com
Email: techsppt@heapg.com
Europe:
Tel: +353-21-4321-266
Fax: +353-21-4321-826
Web: www.horner-apg.com
Email: techsupport@horner-apg.com
No part of this publication may be reproduced without the prior agreement and
written permission of Horner APG, Inc. Information in this document is subject to
change without notice.
