HORNER VIM400 Montageanleitung
To obtain user manual updates, visit our web site at www.heapg.com.
1INTRODUCTION
The Video Capture Option (VIM400) allows four channels of NTSC or PAL video to be connected to an
SVGA OCS 451, 551, or 651. By using the Video Object in Cscape software, video can be displayed on
OCS screens in various sizes shown in Table 1.
The Video Object allows viewing video in a window, freezing the video, saving a single frame of the video
to Compact Flash, or viewing the video full screen with the full frame rate. A separate control register
allows ladder code to optionally freeze or save video snap-shots based on the machine state.
2SPECIFICATIONS
Table 1 –VIM400 Specifications
Colors Maximum 32,768
Video Inputs 4 Video Inputs (NTSC or PAL)
Video Objects Up to 4 Video Objects displayed per screen.
Each Video Object can be optionally set for the user to
dynamically select one of the four inputs.
Resolutions per Video
Object 4
Resolution
(Display Sizes)
•640 x 480 full screen
•640 x 480 pixel size
•320 x 240 pixel size
•160 x 120 pixel size
Signal Form NTSC, PAL
Image Input 1.0Vp-p, 75 ohms imbalance
UL
CE See Compliance Table at
http://www.heapg.com/Support/compliance.htm
08 October 2003 MAN0583-01
Video Capture Option for the
SVGA Color Touch OCS
HE500VIM400
Products Specifications and Installation Data
PAGE 208 OCT 2003 MAN0583-01
2INSTALLATION
The following installation information is provided for SVGA OCS451, OCS551, and OCS651.
2.1 Overview
Figure 1 –VIM400 Overview
2.2 Dimensions
(Unit: mm)
Figure 2 –VIM400
(Unit: mm)
Figure 3 –VIM400 Connector
To Video
Not Supported
MAN0583-01 08 OCT 2003 PAGE 3
2.3 Mounting Procedures
1. Turn off the power supply of the SGVA Color Touch OCS.
2. Remove the dust protection seal that is pasted on the back of the SVGA (CN6)
3. Mount the connector of the VIM400 to the SGVA Color Touch OCS (CN6).
Figure 4 –OCS451 (left) and OCS551 / OCS651 (right)
4. Fix the VIM400 to the SGVA OCS with 4 mounting screws.
Screw points Screw Size Torque
Holes for mounting the unit M3 2.7 –4.4 in-lb
(0.3 –0.5 N-m)
2.4 Communications Cable
A cable is required to connect the video, camera, etc. to the SVGA with a VIM400 module attached.
Figure 5 –BNC Jack and BNC Plug
PAGE 408 OCT 2003 MAN0583-01
3SAFETY
All applicable codes and standards need to be followed in the installation of this product.
4TECHNICAL ASSISTANCE
For assistance, contact Technical Support at the following locations:
North America:
(317) 916-4274
www.heapg.com
Europe:
(+) 353-21-4321-266
www.horner-apg.com
Inhaltsverzeichnis
Andere HORNER Steuereinheit Handbücher
HORNER
HORNER QX351 Series Bedienungsanleitung
HORNER
HORNER HE800FOX100 Montageanleitung
HORNER
HORNER SmartStack HE800JCM100 Bedienungsanleitung
HORNER
HORNER HEXHSQ Bedienungsanleitung
HORNER
HORNER SmartBlock HE579DAC107 Bedienungsanleitung
HORNER
HORNER X OCS Series Bedienungsanleitung
HORNER
HORNER HE800PCU100 Kurzanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
