Hotpoint 22 Series Bedienungsanleitung

www.Hotpoint.com

Refrigerators

Top-Freezer

200D2461P002 39-60294 08-03 JR

Models 22, 25

Owner’s Manual &

Installation Instructions

Safety Instructions

Adapter Plugs . . . . . . . . . . . . . . . . . . . .3

Connect Electricity . . . . . . . . . . . . . . . .3

Extension Cords . . . . . . . . . . . . . . . . . .2

Proper Disposal . . . . . . . . . . . . . . . . . .2

Safety Precautions . . . . . . . . . . . . . . . .2

Operating Instructions

Additional Features . . . . . . . . . . . . . . .7

Automatic Icemaker . . . . . . . . . . . . . . .8

Controls . . . . . . . . . . . . . . . . . . . . . . . .4

Crispers and Pans . . . . . . . . . . . . . . .7, 8

Shelves and Bins . . . . . . . . . . . . . . . .5, 6

Care and Cleaning

Care and Cleaning . . . . . . . . . . . . . . . .9

Replacing the Light Bulbs . . . . . . . . .10

Installation Instructions

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . .11

Reversing the Door Swing . . . . . .16–20

Water Line Installation . . . . . . . .12–16

Troubleshooting Tips . . . . . . . . .21–23

Normal Operating Sounds . . . . . . . .21

Consumer Support

Consumer Support . . . . . . .Back Cover

Warranty . . . . . . . . . . . . . . . . . . . . . . .24

Write the model and serial numbers here:

Model #__________________________

Serial # __________________________

Find these numbers on the gray label

on the left side, near the top of the

refrigerator compartment.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating

element located on the bottom of the icemaker.

Do not place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■Setting the controls to the 0 (off) position does

not remove power to the light circuit. On some

models, only the refrigerator control has a

0 (off) setting.

■

■Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they

will sit for “just a few days.” If you are getting

rid of your old refrigerator, please follow the

instructions below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children

may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.Hotpoint.com

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

If the outlet is a standard 2-prong outlet,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should always be plugged into

its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords

that have become frayed or otherwise damaged.

Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE

the refrigerator until a proper ground has been

established.

Attaching the adapter ground terminal to a wall outlet cover

screw does not ground the appliance unless the cover screw

is metal, and not insulated, and the wall outlet is grounded

through the house wiring. You should have the circuit checked

by a qualified electrician to make sure the outlet is properly

grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

This feature allows you to lock the controls

so the settings cannot be changed.

To lock the controls:

Set the controls to the desired settings.

Press and hold the lock pad for

3 seconds.

When the controls are locked, the indicator

light will come on and the control settings

will not be displayed.

To unlock the controls:

Press and hold the lock pad for 3 seconds.

After unlocking the controls, the settings

will be displayed, the lock indicator light

will go out and the settings can be changed.

About the controls on the refrigerator.

The controls will look like one of the following:

ADJUST REFRIGERATOR TEMP

ADJUST FREEZER TEMP ACTIVATE LOCK

IS COLDEST

9IS COLDEST

HOLD

3 SECS

COLDER WARMER COLDER WARMER

Initially, set the refrigerator control at 5and the freezer control at 5

and allow 12–24 hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one

increment at a time, and allow 12 hours after each adjustment for

the refrigerator to reach the temperature you have set.

Setting the controls to 0 stops cooling in both the refrigerator and

freezer compartments but does not shut off electrical power to

the refrigerator. On some models, only the refrigerator control has

a 0setting.

Touch pad controls

•Setting either control at 0will automatically set the other control at 0.

The zeros will blink until you set the controls.

•If both controls are set at 0and either COLDER pad is pressed, the

controls will automatically reset to 5.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

Locking the Controls (on some models)

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Consumer Support

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

Spillproof Shelves (on some models)

Spillproof shelves have special edges to

help prevent spills from dripping to lower

shelves. To remove or replace the shelves,

see Rearranging the Shelves.

About the shelves and bins. www.Hotpoint.com

Not all features are on all models.

Some models have wire shelves that

can be adjusted in the same manner.

Shelves in the refrigerator and freezer compartments are adjustable.

Rearranging the Shelves

To remove:

Tilt the shelf up at the front.

Lift the shelf up at the back and bring

the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Refrigerator Compartment

To remove:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up and

out of the shelf supports.

To replace:

Holding the shelf diagonally, insert the

left end of the shelf into the center of

the shelf supports on the side wall at the

desired level.

Insert the right end of the shelf into the

shelf supports at the same level. Rest

each end of the shelf on the bottom of

the shelf supports.

NOTE: For models with an automatic icemaker,

the freezer shelf must be in the lower position

for the ice cube bucket to catch the cubes.

Freezer Compartment

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

About the shelves and bins.

Non-Adjustable Shelves on the Door

To remove: Lift the shelf straight up, then

pull out.

To replace: Engage the shelf in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift the bin straight up, then

pull out.

To replace or relocate: Engage the bin in the

molded supports of the door, and push in.

Bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of

the snugger and move it to fit your needs.

Snugger

Freezer Tilt Out Bin (on some models)

Push the button as you tilt out the bin.

To remove: Hold the sides of the bin and

lift it straight up, then pull out.

To replace: Engage the ends of the bin

in the molded supports on the door and

push down. It will lock in place.

NOTE: Do not overload the bin.

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward

until it can be removed.

To replace:

Place the rear shelf tabs just in front of

the central notches on the shelf frame.

Slide the shelf in until the central tabs

are slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after reinstallation

and doesn’t move freely from side to side.

Make sure you push the shelves all the way in

before you close the door.

Finger hold

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

About the additional features. www.Hotpoint.com

Not all features are on all models.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Shelf Saver Rack (on some models)

Slide-out beverage rack holds 12 cans of

soda or 2 wine/water bottles (lengthwise).

It can be removed for cleaning.

To remove, slide the rack out to the stop

position, lift the rack up and past the stop

position and lift it out.

Snack Pan (on some models)

This pan can be moved to the most

useful location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the

stop position and lift it out.

Adjustable Temperature Deli Pan (on some models)

When the pan is placed in the top 6 slots on

the left side and the lever is set at COLDEST,

air from the freezer is forced around the

pan to keep it very cold.

You can move the pan to any location if

you don’t want the extra cold storage.

The settings can be adjusted anywhere

between cold and coldest .

When set at cold, the pan will stay at the

normal refrigerator temperature.

The coldest setting provides the coldest

storage area.

About the crispers and pans.

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

About crisper removal.

Not all features are on all models.

Crisper Removal

To Remove:

These drawers can be removed easily by

lifting up slightly while pulling the drawer

past the stop location.

When the door cannot be fully opened,

remove the drawer farthest from the door

first. Make sure the drawer closest to the

door is fully closed. There is a latch at the

front of the center slide rail. Push down on

the latch and slide the center slide rail, to

which the drawer is attached, away from

the door. Remove the drawer.

Icemaker

Feeler Arm

Power Switch

Green

Power Light

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Automatic Icemaker (on some models)

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on

freezer compartment temperature,

room temperature, number of door

openings and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch to O (off).

When the refrigerator has been connected

to the water supply, set the power switch to

I (on). The green light will come on.

The icemaker will fill with water when it

cools to 15°F. A newly-installed refrigerator

may take 12 to 24 hours to begin making

ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

If ice cubes get stuck in the icemaker, the

green power light will blink. To correct this,

set the power switch to O (off) and remove

the cubes. Set the power switch to I (on) to

restart the icemaker.

After the icemaker has been turned on

again, there will be a delay of about

45 minutes before the icemaker resumes

operations.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for

the specific icemaker kit needed for

your model.

Behind the Refrigerator

Be careful when moving the refrigerator away

from the wall. All types of floor coverings can be

damaged, particularly cushioned coverings and

those with embossed surfaces.

Pull the refrigerator straight out and return it to

position by pushing it straight in. Moving the

refrigerator in a side direction may result in

damage to the floor covering or refrigerator.

When pushing the refrigerator back, make sure you don’t

roll over the power cord or icemaker supply line (on some

models).

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Cleaning the Outside

The door handles and trim. Clean with a cloth

dampened with soapy water. Dry with a soft

cloth.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with mild liquid dish

detergent. Dry with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet

towel. These may leave a residue that can erode the paint.

Do not use scouring pads, powdered cleaners, bleach or

cleaners containing bleach because these products can

scratch and weaken the paint finish.

Care and cleaning of the refrigerator. www.Hotpoint.com

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda to a

quart (1 liter) of water. This both cleans and

neutralizes odors. Thoroughly rinse and wipe

dry.

Avoid cleaning cold glass shelves (on some models) with

hot water because the extreme temperature difference

may cause them to break. Handle glass shelves carefully.

Bumping tempered glass can cause it to shatter.

Do not wash any refrigerator parts in the dishwasher.

Wash ice trays in lukewarm water only—do not put them

in an automatic dishwasher.

Preparing for Vacation

For long vacations or absences, remove food and

unplug the refrigerator. Move the freezer control

to the O (off) position, and clean the interior with

a baking soda solution of one tablespoon (15

ml) of baking soda to one quart (1 liter) of

water. Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing, have

a qualified servicer drain the water supply system

(on some models) to prevent serious property

damage due to flooding.

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them securely

in place to prevent damage.

Be sure the refrigerator stays in an upright position

during moving.

Light shield

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Replacing the light bulbs.

Turning the control to the 0 (off) position does not remove power to the light circuit.

Refrigerator Compartment

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulbs are located at the top of

the refrigerator compartment near

the opening. On some models, a light

shield will have to be removed.

To remove the light shield, grasp the

shield as shown. Squeeze the shield

and rotate the shield toward the back

of the refrigerator. The light shield

will pop out.

Replace the bulb with an appliance

bulb of the same or lower wattage.

On models with a light shield, replace

the light shield.

Plug the refrigerator back in.

Freezer Compartment Light (on some models)

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located behind a light

shield at the back of the freezer

compartment. To remove, squeeze

the top and bottom of the shield and

pull the shield off.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Freezer Compartment Dome Light (on some models)

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located at the top of the

freezer compartment inside the dome

light shield. To remove the shield, place

your finger in the pocket at the back

of the shield. Pull the shield forward

and down.

After replacing with an appliance

bulb of the same or lower wattage,

replace the shield.

Plug the refrigerator back in.

Pocket

Andere Handbücher für 22 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hotpoint Kühlschrank Handbücher

Hotpoint

Hotpoint HMB312AAI Bedienungsanleitung

Hotpoint

Hotpoint HBT 18I Bedienungsanleitung

Hotpoint

Hotpoint CTX18EACAA Bedienungsanleitung

Hotpoint

Hotpoint ENXTLH 19xxx FW L 03 Bedienungsanleitung

Hotpoint

Hotpoint ENXTY 19 FO3 Series Bedienungsanleitung

Hotpoint

Hotpoint RF175BG Bedienungsanleitung

Hotpoint

Hotpoint HTS17BBSLCC - 16.6 cu. Ft. Top Freezer... Bedienungsanleitung

Hotpoint

Hotpoint MTM 081 F/HA Bedienungsanleitung

Hotpoint

Hotpoint HTS22GBMARCC Originalbetriebsanleitung

Hotpoint

Hotpoint FFP187MG Bedienungsanleitung

Hotpoint

Hotpoint FFU3DG K Bedienungsanleitung

Hotpoint

Hotpoint HTR16ABSLCC - R 15.6 cu. Ft. Top-Freezer... Bedienungsanleitung

Hotpoint

Hotpoint HTR18ABR Bedienungsanleitung

Hotpoint

Hotpoint FFLAA58WDW Bedienungs- und Montageanleitung

Hotpoint

Hotpoint FF46TP Bedienungsanleitung

Hotpoint

Hotpoint MSZ 906 DF (UK) Bedienungsanleitung

Hotpoint

Hotpoint 15 Bedienungsanleitung

Hotpoint

Hotpoint HMB312I Bedienungsanleitung

Hotpoint

Hotpoint XAL85 Series Bedienungsanleitung

Hotpoint

Hotpoint CSX22T Montageanleitung

Hotpoint

Hotpoint ENXTY 19 FW O3 TK Series Bedienungsanleitung

Hotpoint

Hotpoint HME03GGM Betriebsanleitung

Hotpoint

Hotpoint RLAV21K Bedienungsanleitung

Hotpoint

Hotpoint CSM22GRD WW Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung