Hotpoint HS2321L Bedienungs- und Montageanleitung

Indesit Company UK Ltd

Service

Information

Built In

Integrated

Larder

Fridges

Models Comm.

Covered Code

HS2321L 54085

HS2322L 77819

5407691 Issue 1 Dec. 2012

SM003482 ~ C00291854

2 of 17

Service Manual UK

Indesit

Company

English

HEALTH AND SAFETY

For the servicing of refrigeration products, containing Isobutane R600a refrigerant.

These instructions are in addition to any other Company procedures already published.

Published primarily for Indesit Company engineers working in the UK or Southern Ireland, for

which these instructions are MANDATORY.

1. Only engineers who have been trained on the safe handling of Isobutane R600a refrigerant are

authorised to transport, store or carry out system repairs.

2. This manual is not intended as a comprehensive repair/maintenance guide to the appliance.

3. Must only be used by suitably qualified persons having technical competence, applicable product

knowledge, suitable tools and test equipment.

4. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged

from the electrical supply).

5. Servicing must be preceded by earth continuity and insulation checks, plus refrigerant leak

detection.

6. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.

7. After servicing, the appliance must be rechecked for electrical safety.

8. Smoking, naked flames, or operating gas and/or electrical equipment (including cordless power

tools) are forbidden within the storage area, working area and vehicles used to transport Isobutane.

9. The carrying case for the scales and refrigerant must display a red flammability label

Part Number 8100063 that should be visible and readable at all times.

10. The vehicle and storage area must be ventilated as far as is reasonably practicable and the

aluminium case kept out of direct sunlight. The storage temperature of Isobutane should not exceed

50°C.

11. The vehicle transporting Isobutane (R600a) refrigerant must display a Red Flammable Gas warning

sticker (Part No. C00247960 [(8100063)].

12. Engineers should not wear clothes that are liable to cause static discharge ('electrostatic sparking').

13. Avoid working in small rooms.

14. Do not work in cellars.

15. Whenever possible move the appliance into a larger open area away from possible ignition sources.

16. Request the customer to turn off all other electrical and gas appliances in the near vicinity of the

repair and note that it is done.

Customers should be advised to restrict activity within the near vicinity for a short time.

17. Isobutane refrigerant must be vented to atmosphere, (outside of the premises e.g. via open window

through the clear plastic hose supplied).

18. Isobutane is heavier than air and must not be vented within 3 metres of the following: sewer cover,

cellar, drain or any similar construction lower than ground level, boiler air inlet/outlet, or near any

possible source of ignition.

continued...

3 of 17

Indesit Company

Service Manual UK English

HEALTH AND SAFETY

19. Working with a naked flame i.e. soldering or brazing is forbidden. Unless otherwise stated, pipework

connections must only be made using the Lokring coupling system.

20. Electronic leak detectors with high voltage tips must NOT be used with any Isobutane (R600a).

21. All equipment used for this activity must be checked regularly and maintained in a safe working

condition; parts must be replaced as required.

Information Regarding Isobutane Canisters

1. The maximum quantity of Isobutane an engineer should hold or store at any one time is two 1kg net

aluminium canisters, supplied individually as Part No. C00218421 (2602600).

2. Canisters must be stored inside the aluminium case with the weighing scales for protection from

possible damage and heat. The aluminium case must NEVER be placed next to a heat source or

in direct sunlight.

3. Isobutane must only be dispensed to the appliance from the 1kg net aluminium canister placed in

an upright position on the weighing scales provided.

4. All used canisters must be a returned as scrap and therefore, left out for the driver to collect and

return for disposal.

5. Canisters must not be punctured or the internal valve damaged.

6. Before storing the canister it must have the extraction tap valve removed and the internal valve of

the canister checked for leakage using leak detector (Leak Detector: Part No. C00222861

(5700043).

7. All used canisters and those found to be leaking should be exhausted to atmosphere to ensure they

are emptied completely. Refer to the following paragraph.

8. Refit the extraction tap if necessary, open the tap and then invert the canister.

This must be done outside in open air away from buildings and ignition sources and complying with

Item 18 on previous page.

4 of 17

Service Manual UK

Indesit

Company

English

INDEX

Health & Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Overall View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Autotest Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Replacement Door Seals for Door Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Replacing the light Bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Module and Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Programming (EMIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 12

Programming Flowchart (Smartcard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting the Low End Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Module Light Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installation and Door Reversal Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

INTRODUCTION

The interior has one fruit and vegetable crisper with a glass cover, four removable, height adjustable

shelves, one hinged bottle rack. The door has one removable door shelf with a lid, an egg tray, lidded

butter dish, two removable commodity shelves, a compartment for a 2 litre bottle and one removable

door shelf for bottles.

The HS2321L model is an over counter 216 litre larder fridge and is manufactured in Italy.

The product was launched November 2008.

The HS2322L is the same as HS2321L, and was launched March 2012.

The electronic thermostat, interior light and light switch are contained in the control box mounted in the

top right hand side of the fridge.

Please refer to Technical Specifications for Climate Class and dimensions.

As with many refrigeration appliances it is important that it is installed and operated within the

recommended ambient temperature range and that there is also adequate ventilation.

5 of 17

Indesit Company

Service Manual UK English

TECHNICAL SPECIFICATIONS

Colour Polar White

Introduction Date HS2321L - November 2008

HS2322L - March 2012

Mode of Installation Built In (Integrated)

Door Hinging Doors are hinged on the Right Hand side as supplied.

The door is reversible.

Dimensions Unpacked Packed Minimum Aperture

Height 1224 mm 1290 mm 1225 mm

Width 540 mm 590 mm 560 mm

Depth 550 mm 620 mm 550 mm

Weight 36.0 Kg 39.5 Kg

Total Capacity Gross: 216 litres

Net: 213 litres

Defrosting Automatic

Climate Class HS2321L - N/ST (+16°C to +38°C)

HS2322L - SN/N/ST/T (+10°C to +43°C)

Energy Consumption HS2321L - to 1998 Regulations

161 kWh / year

0.44 kWh / 24 hours

HS2322L - to 2011 Regulations

138 kWh / year

0.38 kWh / 24 hours

Energy Band HS2321L = A

HS2322L = A+

Compressor Electrolux Embraco

HTK70AA EMX26CLC

Winding Resistances: Start = 24.6 Ohms Start = 24.6 Ohms

Run = 28.1 Ohms Run = 28.1 Ohms

Mains Cable Length 2 metres

Electrical Supply 240 Volts AC @ 50 Hz

Refrigerant Charge - R600 Refer to Rating Plate

6 of 17

Service Manual UK

Indesit

Company

English

OVERALL VIEW - refer to illustration below

Interior Lamp

Control Panel

& Cover

Light

switch

7 of 17

Indesit Company

Service Manual UK English

AUTOTEST MODE

Autotest Function:

To start Autotest:

a. With the Fridge Door open, push and hold in the Light switch button (light Off position). See item 4

above.

b. Press and hold the "3" key (see above) on the control panel for 5 seconds. The test sequence will

begin.

Autotest Sequence:

All LEDs on the control panel are off during the AUTOTEST procedure.

At the end of the AUTOTEST the appliance returns to the “ON” position at a temperature of + 4°C.

Press the button on the control panel or unplug the appliance to stop the AUTOTEST procedure.

Alarm Messages:

There is only one alarm message: NTC short circuited / open. Alarm on: refrigerator light blinks.

The alarm is only signalled during the autotest.

Temperature Alarm:

The temperature alarm (indicated by the flashing set temperature LED and a buzzer) comes on

automatically when the NTC probe measures a temperature of above 10°C for more than 30 minutes.

Reset Temperature Alarm:

If a temperature alarm has been generated, press the ON/OFF / SET TEMPERATURE key, (the only

key on the control panel) to reset the alarm and make the product switch to OFF state.

Step Duration Action Light AIR

Fan Notes

15 sec Pause OFF OFF --

21 sec Check probe OFF OFF If probe is faulty go to Step 3

If probe is OK, go to Step 4

3249 sec Activate AIR Fault

error message

Interior

light

blinks

ON End of autotest procedure

4249 sec Activate AIR Probe

OK message ON ON End of autotest procedure

1 - Super Cool LED

2 - Temp LED’s

3 - Selector Button

Light switch

button

Shown

pushed in

8 of 17

Service Manual UK

Indesit

Company

English

REPLACEMENT DOOR SEALS FOR DOOR ASSEMBLIES

Various types of door seal are supplied as replacements. See Figs. A, B and C showing seal profiles.

Note also the liner profiles A5, A6 and B5, B6 below.

The door seal, Fig. A, is retained by the liner which has 2 screws securing each corner.

The door seal as illustrated in Fig. B is not available as a spare part, but the seal as shown in Fig. C is

supplied as the replacement.

Removing the Old Door Seal - See Figs. D to L.

Remove the door from the

appliance and place on a flat

protected surface. Cut the seal

across each corner (including

the rigid tongue section retained

by the liner). Each section can

then be withdrawn from the liner

using snipe nosed pliers and

pulling. Where the seal is

particularly tight in the liner slot,

it might be helpful to ease the

edge of the liner away from the

door panel using a wide bladed

screwdriver or chisel knife,

Part No. C00222502 (5500012).

Similar practice should be

adopted when fitting the

replacement seal.

Once the seal is removed and

the liner seal pocket is empty, it

can be helpful to insert the

chisel knife between the liner /

door panel and slide it around

the door to clear any debris.

Fitting the Replacement Seal

Insert the replacement door seal rigid tongue between the liner and door panel and push into position,

Fig. B. It may be necessary to insert a chisel knife between the liner and door panel to get the seal

started.

AB C

9 of 17

Indesit Company

Service Manual UK English

Replacing the Light Bulb

To replace the light bulb in the refrigerator compartment,

1. Pull out the mains plug from the electrical socket.

2. Access the light bulb by removing the cover as indicated in the diagram below.

3. Unscrew the faulty bulb.

4. Replace it with a similar light bulb within the power range indicated on the cover (10 Watt or 15 Watt).

Indesit Company

10 of 17

Service Manual UK English

Module and Wiring Diagram

Key:

L 4

L 1

L 3 L 2

AC: Alternating current

LF: Refrigerator light

MV: Motor fan

CO: Compressor

PT: PTC relay

RH: Circuit breaker

PR: Refrigerator light

button/ magnetic reed

switch

S: Probe

C: Start condenser (where

installed)

LZ: Freezer light

RC: FZ frame resistor (where

installed)

HS2321L

HS2322L

Andere Handbücher für HS2321L

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hotpoint Kühlschrank Handbücher

Hotpoint

Hotpoint HM 3x AA Bedienungsanleitung

Hotpoint

Hotpoint HTS17BCSLWW - 16.6 cu. Ft. Top Freezer... Bedienungsanleitung

Hotpoint

Hotpoint CTX18GICAA Bedienungsanleitung

Hotpoint

Hotpoint 6980 Bedienungsanleitung

Hotpoint

Hotpoint GMR04HASCS Montageanleitung

Hotpoint

Hotpoint HTS18BBP Bedienungsanleitung

Hotpoint

Hotpoint ETMP 460 XB TK Bedienungsanleitung

Hotpoint

Hotpoint XH9 Series Bedienungsanleitung

Hotpoint

Hotpoint HM 3x AA F Bedienungsanleitung

Hotpoint

Hotpoint DC 85 Series Bedienungsanleitung

Hotpoint

Hotpoint FFA97 Bedienungsanleitung

Hotpoint

Hotpoint HTS16BCR Bedienungsanleitung

Hotpoint

Hotpoint HM315I Bedienungsanleitung

Hotpoint

Hotpoint CTA12 Technisches Datenblatt

Hotpoint

Hotpoint CTF14 Montageanleitung

Hotpoint

Hotpoint No-frost models Betriebsanleitung

Hotpoint

Hotpoint FFIAA52P Bedienungsanleitung

Hotpoint

Hotpoint MSZ802DF Bedienungsanleitung

Hotpoint

Hotpoint FFA90 Bedienungsanleitung

Hotpoint

Hotpoint ENBGH 19xxx FW Bedienungsanleitung

Hotpoint

Hotpoint FF40 Bedienungsanleitung

Hotpoint

Hotpoint FFA52 Series Bedienungsanleitung

Hotpoint

Hotpoint FFA90 Bedienungsanleitung

Hotpoint

Hotpoint ENXTY 19 FO3 Series Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung