Hotpoint BWM12 Bedienungsanleitung

Congratulations on the purchase of your new

built-in appliance.

IMPORTANT INFORMATION

Please read this Instruction Manual

thoroughly before installing and using

your appliance for the first time.

Instructions for

Installation and Use

For Integrated Washer and Washer Dryer

Models BWM12 & BWD12

WARNING:This appliance must be earthed.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only

those rated at 13A and ASTA approved to BS1362 should be used.To change the fuse in a

moulded plug, lift holder to vertical position and lift fuse out. To replace, insert fuse and push

fuse holder down into locked position. Correct replacement is identified by colour coding or the

marking on base of plug.

WARNING: Do not use plug unless fuse holder is in locked

position and fuse cover fitted.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING:To avoid a shock hazard do not insert the discarded plug into a socket anywhere else.

IMPORTANT:WIRES IN THE MAINS LEAD

ARE COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE:

Green/Yellow - Earth

Blue - Neutral

Brown - Live

If you change the plug, the colour of

wires in the mains lead may not

correspond with the colour of the

markings identifying terminals in the plug.

You should therefore wire it as shown.

Recommendations for the Electrical Installation of your Appliance

●

Do not use extension leads, adaptors or multiple plugs.

●

Never remove the earth connection.

●

You should plug your appliance into a socket that is easily accessible but out of reach of

children.

If in doubt, get in touch with your installer.

Changing the Mains Lead

A special lead can be ordered from Service UK: 08709 066 066 or

Republic of Ireland: 1850 302 200

If you have damaged the existing lead or require a longer one a charge will be made.

It is strongly advised that this work is carried out by a qualified electrician.

CE marking certifies that this appliance conforms to the following EEC directives:-

Low Voltage Equipment - 73/23/EEC

Electromagnetic compatibility - 89/336/EEC (including the modification directive

92/31/EEC)

Electricity Supply

Green and yellow (Earth)

wire to terminal

marked ‘E’,

symbol , or

coloured green

and yellow.

Blue (Neutral)

wire to terminal

marked ‘N’ or

coloured black.

13A ASTA approved

fuse to BS1362.

Brown (Live)

wire to terminal

marked ‘L’ or

coloured red.

Cord clamp

IMPORTANT INFORMATION:

●

Do not plug in and switch appliance on at the mains until installation is complete.

●

You may be charged for a service call if a problem with your appliance is caused

by incorrect installation or misuse.

Electricity Supply ...................................... 2

Recycling & Disposal Information .............. 3

Installation Instructions

............ 3

i. Remove Transit Bolts ....................... 4

ii. Choose a Location... ... 4

iii. Connect to the Water Supply........... 5

iv. Connect to a Drainage System.............. 6

v. Fitting the Door Panels and Plinth........ 7

vi. Fitting your appliance into your kitchen.. 9

vii. Levelling................... 10

The Controls

.................................. 11

Getting to know your Appliance:

Washing Machine BWM12............................12

Washer Dryer BWD12.....................................13

Choosing a Programme:

Washing Machine BWM12............................14

Washer Dryer BWD12.....................................15

The Dispenser Drawer

......................

Using your Appliance

......................

Washcare Tips

......................

Cleaning

.......................................... 20

Troubleshooting

General Maintenance

................... 21

After Sales

Service

..................................................... 22

Guarantee

Guarantee Terms & Conditions ............... 23

Key Contacts

................................. Back Page

Retention of this

Instruction Manual

Keep this instruction manual in a

handy place for reference.

It contains important details on

the safe and proper use of your

appliance. If you sell the

appliance, pass it on to someone

else, move house and leave it

behind, make sure that you

provide this manual so that the

new owner can become familiar

with the appliance and safety

warnings.

Contents

Follow these 7 steps for a trouble free installation:

i. Remove the Transit Bolts...

ii. Choose a Location...

iii. Connect to the Water Supply...

iv. Connect to a Drainage System...

v. Fitting the door panels and plinth...

vi. Fitting your appliance into your

kitchen...

vii. Levelling...

Installation Instructions

IMPORTANT INFORMATION:

●

Do not plug in and switch appliance on at the mains until installation is complete.

●

You may be charged for a service call if a problem with your appliance is caused

by incorrect installation or misuse.

i.Remove Transit Screws...

BEFORE ATTEMPTING TO USE THE MACHINE,YOU MUST FOLLOW THE PROCEDURE DESCRIBED BELOW.

The inside of the appliance is supported, for transportation, by four screws on the back panel. Before

using the appliance these MUST be removed. NOTE: You may need a second person to help you.

Remove the screws , along with the

spacers together with the washers

intact.

You must now cover the holes with the

four plastic covers provided.

The choice of location for your appliance will influence its performance.

●

Position where possible on a solid floor.Vibration may occur with a wooden floor.

●

Take care with vinyl floor coverings.The weight of the appliance may cause indentations in some

vinyl floor coverings.

●

You should not install your appliance on a carpeted floor, but if this is unavoidable, ensure that air

can circulate around its base.

●

If locating next to another appliance or an item of furniture, leave space between them to allow air

to circulate.

●

For your safety and to comply with IEE regulations, you should not install your appliance in a bath

or shower room. Seek professional advice if you wish to do so.

●

Ensure sufficient space is allowed for the appliance.

●

Ensure the electrical socket and water taps are easily accessible and that the water supply can be

isolated if necessary.

●

Risk of freezing: Do not position the appliance in rooms exposed to frost.

Frozen pipes may burst under pressure.

ii. Choose a Location...

Important: Use the cap supplied to close the 3 holes which housed the plug, situated in the

right hand part of the lower back of the appliance.

WARNING:

●

The appliance must not

be plugged into the

mains supply until all

installation instructions

have been completed.

●

Retain the transit

screws, spacers and

washers. Should you

move house then these

should be replaced to

support the inside of the

appliance to prevent

damage when in transit.

iii. Connect to the Water Supply...

●

Water taps and standpipe should be situated away from the rear of appliance but in easy

access for turning on and off.

●

For your machine to operate correctly it requires water pressures in the range of 6-150 psi

(100 - 1000KPa). Most water supplies will be in this range.

●

Connect the hoses to the water supply pipes at the rear of the appliance

and onto the water supply taps (Red end fitting to the hot water supply

and adjacent to‘H’ on the rear of the appliance and White end fitting to

the cold water supply and adjacent to ‘C’ on the rear of the appliance).

Remember to insert a sealing washer (A) to ensure each connection is

watertight.

Fit securely and turn on the water supply to check for leaks.

If there is a leak, turn off the water supply, remove the connector

and check that the sealing washer is in place. Refit the connector

and tighten it. Turn on the water supply.

Note: Do not over tighten the water supply pipe connection. Hand

tight should be sufficient.

We recommend you use the new hoses provided with your appliance to ensure correct

connections and prevent leaks.

WARNING

●

Do not connect

appliance to a single

outlet instantaneous

water heater.

Remember you may be

charged for a service

call if a problem with

your appliance is

caused by incorrect

installation or misuse.

If the fill hoses are too short:

If you have no hot water supply or your hot water pressure is low:

Longer fill hoses are available from our Genuine Parts and

Accessories Mail Order Hotline

UK on 08709 077 077

(or in the Republic of Ireland on (01) 842 6836).

Remove the existing fill hoses from the inlet valves on the

back of the machine and fit the new longer fill hoses as shown

with the angled ends of the hoses connected to the machine.

A cold fill adaptor and fitting instructions are available from

your local Hotpoint authorised Service Centre or by calling the

Genuine Parts and Accessories Mail Order Hotline

UK on 08709 077 077

(or in the Republic of Ireland on (01) 842 6836).

A cold fill adaptor

iv. Connect to a Drainage System...

●

Connect up the drain hose, after fitting the hooked end support supplied in the machine.

●

Ensure the drainage hose is not obstructed,trapped or kinked.

●

Any extension of the drainage pipe must be no longer than 1 metre, it must have the same

inner diameter and must have no constrictions of any nature.

●

Do not position standpipe near an electrical outlet.

We recommend one of the following drainage methods:-

Standpipe

Note: Ensure the standpipe has a minimum diameter of 38mm.

●

The standpipe should be installed away from the

rear of the appliance.

1. Ensure hooked end of drain hose is positioned between 100

and 60cm above the bottom of the machine.

2. Untie the end of the GREY drainage hose from the rear of the

appliance and place approximately 100mm into the standpipe or

sink trap spigot.

●

Ensure the drain hose is firmly in position, to prevent it coming

away while the machine is in use and causing a flood.

Sink Waste System

Note: Ensure the sink outlet pipe has a minimum diameter of 32 mm.

1. Untie the end of the GREY drainage hose from the

rear of the appliance.

2. Reposition ‘hooked end’ support as required along the GREY

drainage hose.

3. If fitting an under sink waste disposal unit cut out the

membrane, bung or blanking plug.

4. Attach the GREY drainage hose to the under sink waste

disposal unit securely, using a suitable hose clip.

5. Raise the hose to a minimum height of between

90 and 65cm to avoid syphoning.

●

Ensure the drain hose is securely attached, to prevent it coming

away while the machine is in use and causing a flood.

cut off end

If the GREY drainage hose is too short:

A longer drainage hose is available from our Genuine Parts & Accessories Mail Order Hotline

UK on 08709 077 077 (or in the Republic of Ireland on (01) 842 6836).

hose clip

v. Fitting the Door Panel...

●

The wooden panel that

covers the face of the machine

must not be less than 18mm

in thickness and can be

hinged on either side.

For practical reasons, it is

advisable to maintain the

same opening direction as the

appliance door itself (hinges

applied to the left hand side).

DOOR MOUNTING ACCESSORIES:

The packaging is designed to

make it possible to mount the

wooden panel onto the appliance

without removing it completely.

6 x type A self threading screws 1=13mm

2 x type B metric countersunk screws 1=25mm, for fastening

the magnet plate to the cabinet

4 x type C metric screws 1=15mm, for mounting the hinge

supports to the cabinet

4 x type D metric screws 1=7mm, for mounting the hinges on

the supports

Fitting the Door Panel and Plinth...

Mounting parts onto the face of the appliance:

-Mount the hinge supports onto the face of the machine, positioning the hole indicated by

the arrow, in Fig.1, towards the inside of the face and using the type C screws.

- Mount the magnetic plate on the opposite side, at the top, using the two type B screws.

- Place the spacer illustrated in Fig 4/B between the machine front and the magnet receiver.

Using the drilling template:-

Proceed as follows when applying the panel to the appliance:

- To trace the positions of the holes on the left hand side of the panel, align the drilling

template to the top left side of the panel, using the lines traced on the extremities as a

reference.

- To trace the positions of the holes on the right hand side of the panel, align the drilling

template to the top right side of the panel.

- Use an appropriately sized router to mill the holes for the two hinges, the rubber plug and

the magnet.

Mounting the parts onto the wooden door panel:-

- Insert the hinges into the holes (NB. the movable part of the hinge must be positioned

facing away from the panel) and fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the opposite side of the hinges and fasten it with

the 2 type B screws.

- Insert the rubber plug into the bottom hole.

- The panel is now ready to be mounted onto the machine.

Mounting the panel onto the machine:-

- Insert the nib of the hinge (indicated by the arrow in Fig.2) into the hole for the hinge and

push the panel towards the front of the machine. Fasten the two hinges with the type D

screws.

Fastening the plinth guide:-

If the machine is installed at the end of a set of modular cabinets, mount either one or both of

the guides for the base moulding (as shown, Fig.6).

Adjust them for depth, based on the position of the base moulding and if necessary fasten the

base to the guides (Fig.7).

This is how to assemble the plinth guide (Fig.6).

- Fasten angle Pusing screw R, insert plinth guide Qinto the special slot and once it is in the

desired position, lock it in place using angle Pand screw R.

Fig.6 Fig.7

Remember you may be

charged for a service

call if a problem with

your appliance is

caused by incorrect

installation or misuse.

Inserting the machine into the cabinet:-

- Push the machine into the opening, aligning it with the cabinets (Fig.8).

- Regulate the adjustable feet to raise the machine to the appropriate height.

- To adjust the position of the wooden panel in both the vertical and horizontal directions,

use the C and Dscrews, as shown in Fig.9.

Important: Close the lower part of the appliance front by ensuring that the plinth rests against the

floor.

Move the appliance into position, care must be taken that the Water Supply pipes and the

Drainage hose are not kinked or trapped.

Direct the mains cable towards the electrical socket to be used but DO NOT plug in at this

stage.

There must be at least 2mm clearance at the sides and top of the appliance. The back of

the appliance must also remain some distance away from the back wall. If the recessing cavity

is higher than 820mm, the opening between the floor and sides of the appliance (when

installed at the end of a line of furniture) must be completely closed in.

vi. Fitting your appliance into your

kitchen...

Fig. 8 Fig. 9

vii. Levelling...

Adjust the feet until all four feet are in firm contact with the floor ensuring the

appliance stands level in every direction. You can check this using a spirit level.

We recommend you level the appliance to prevent vibration being transmitted to

the surrounding furniture, check that the sides and the top of the appliance are

unable to touch the furniture.

Accessories provided for height adjustment

The following can be found inside the polystyrene lid (Fig.10):

2 x crossbars (G)

1 x strip (M)

The following can be found inside the appliance drum:

4 x adjustable feet (H)

4 x screws (I)

4 x screws (R)

4 x nuts (L)

2 x plinth guides (Q)

Adjusting the appliance height

The height can be adjusted (from 815mm to 835mm), by turning the 4 feet.

Should you require the appliance be placed higher than the above height you

need the following accessories to raise it up to 870mm:

- the 2 x crossbars (G)

- the 4 x adjustable feet (H)

- the 4 x screws (I)

- the 4 x nuts (L)

Then carry out the following steps (Fig.11):

Remove the 4 original feet, place a crossbar Gat the front of the machine, fasten

it in place using screws I(screwing them in where the original feet were) then

insert the new feet H.

Repeat at the back of the appliance.

Now adjust the feet Hto raise or lower the appliance from 835mm to 870mm.

Once you have reached the desired height lock the nuts Lonto the crossbar G.

To adjust the appliance to a height between 870mm and 900mm you need to

mount strip M, adjusting feet Hto the required height.

Insert strip Mas follows: Loosen the three screws Nsituated at the front of the

top cover of the appliance, insert strip Mas shown in Fig.12, then fasten screws

Fig. 10 Fig. 11 Fig. 12

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hotpoint Waschmaschine Trockner Handbücher

Hotpoint

Hotpoint AQUALTIS AQM8D 69 I Bedienungsanleitung

Hotpoint

Hotpoint BHWD129 Bedienungsanleitung

Hotpoint

Hotpoint AQD1072D 697 Bedienungsanleitung

Hotpoint

Hotpoint WDUD 9640 Bedienungsanleitung

Hotpoint

Hotpoint FDL 9640 Bedienungsanleitung

Hotpoint

Hotpoint Aquarius Bedienungsanleitung

Hotpoint

Hotpoint WDD 960 P Bedienungsanleitung

Hotpoint

Hotpoint ARMXXD 109 Bedienungsanleitung

Hotpoint

Hotpoint WDL 5290 Bedienungsanleitung

Hotpoint

Hotpoint WDD 10760 Bedienungsanleitung

Hotpoint

Hotpoint WD440 Bedienungsanleitung

Hotpoint

Hotpoint WDL 520 P Bedienungsanleitung

Hotpoint

Hotpoint WDL520P Bedienungsanleitung

Hotpoint

Hotpoint FDEU9640P Bedienungsanleitung

Hotpoint

Hotpoint Aqualtis AQGMD149 Bedienungsanleitung

Hotpoint

Hotpoint RD 1176 J Bedienungsanleitung

Hotpoint

Hotpoint WDAL 8640 Bedienungsanleitung

Hotpoint

Hotpoint WDXD 8640 Bedienungsanleitung

Hotpoint

Hotpoint AQD970D49 Bedienungsanleitung

Hotpoint

Hotpoint AQUALTIS AQD970D 49 Bedienungsanleitung

Hotpoint

Hotpoint WDD740 Bedienungsanleitung

Hotpoint

Hotpoint WDL 5290 P Bedienungsanleitung

Hotpoint

Hotpoint RG 864 Bedienungsanleitung

Hotpoint

Hotpoint WDUD 9640 Bedienungsanleitung

Beliebte Waschmaschine Trockner Handbücher anderer Marken

Whirlpool

Whirlpool WFC8090GX Bedienungsanleitung

Whirlpool

Whirlpool LTE5243DQ6 Bedienungsanleitung

Bosch

Bosch XQG100-WDU285H00W Bedienungsanleitung

montpellier

montpellier MWD7512S Bedienungsanleitung

LG FHD0905 T Series Bedienungsanleitung

Midea

Midea MF200D85B Bedienungsanleitung

Maytag

Maytag MGT3800XW Bedienungsanleitung

Siemens

Siemens WD15G440TR Technisches Datenblatt

Equator

Equator Clothes Processor EZ1500 Bedienungsanleitung

Splendide

Splendide WDC7100XCP Bedienungsanleitung

John Lewis

John Lewis JLWD 1408 Bedienungsanleitung

Ariston

Ariston A1200WD Bedienungsanleitung

Whirlpool

Whirlpool YLTE5243DQ5 Bedienungsanleitung

Whirlpool

Whirlpool WFCR 75230 Installationsanleitung

ATT

ATT Hammer Jet v1 Bedienungsanleitung

AEG

AEG LAVAMAT 63742 VI Bedienungsanleitung

Electrolux

Electrolux EWW8024P5WB Bedienungsanleitung

GE GTD42EASJWH Bedienungsanleitung