Hotpoint EVOII WMF720PUK.R Bedienungs- und Montageanleitung

Indesit Company UK Ltd

Service

Information

WASHING

MACHINES

(Digit LED)

Models Comm.

Covered Code

EVOII

WMF720PUK.R 66119

WMF720GUK.R 66120

Arcadia

WMF720PUK.RA 66119

WMF720GUK.RA 66120

5407522 Issue 1 Dec. 2009

2 of 30

Service Manual UK

Indesit

Company

English

SAFETY NOTES & GENERAL SERVICING ADVICE

1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.

2. It should ONLY be used by suitably qualified persons having technical competence applicable

product knowledge and suitable tools and test equipment.

3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)

from the electrical supply.

4. Servicing must be preceded by Earth Continuity, Earth Resistance and Insulation Resistance

checks.

5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.

6. After servicing the appliance must be rechecked for Electrical Safety. In the case of appliances

which are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.)

checks must be made for leaks from seals gaskets and pipe work and rectification carried out where

necessary.

7. Itcanbedangeroustoattempt 'DIY' repairs /maintenance on complex equipmentandtheCompany

recommends that any problem with the appliance is referred to its own Service Organisation.

8. WhilsttheCompany hasendeavouredtoensurethe accuracyof the datawithin this publicationthey

cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.

SERIAL NUMBER / INDUSTRIAL CODE EXPLANATION

Serial Number Example

3 10 02 0895

Four remaining digits = Build number that day 895th built

Third two digits = Day of manufacture 2nd of month

Second two digits = Month of manufacture October

First digit = Year of manufacture 2003

Industrial Code Example

37 24455 0010

Last four digits = 0000 original production.

Second five digits = COMMERCIAL CODE*

First two digits = Factory of origin

* Vital for correct model information and system identification

Other numbers denote major production changes

3 of 30

Indesit Company

Service Manual UK English

INDEX

Safety & Servicing Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Serial Number Information, Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Controls Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Wiring Diagram - EVO II Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Wiring Connection Chart - EVO II Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Power Module Connections - EVO II Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Wiring Diagram - Arcadia Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Error Codes & Possible Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 - 21

Main Board Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 - 23

Dismantling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 - 29

4 of 30

Service Manual UK

Indesit

Company

English

SPECIFICATIONS

Models Covered WMF720PUK.R (66119) - EVOII Controls

WMF720PUK.RA (66119) - Arcadia Controls

WMF720GUK.R (66120) - EVOII Controls

WMF720GUK.RA (66120) - Arcadia Controls

Colour P = White G = Graphite

Country of Origin WMF720PUK.R - (66119) Radomsko factory (30) Poland

WMF720PUK.RA - (66119) Radomsko factory (30) Poland

WMF720PUK.R - (66120) Radomsko factory (30) Poland

WMF720GUK.RA - (66120) Radomsko factory (30) Poland

Electrical Supply 220 - 240 Volt AC @ 50 Hz Fuse 13 amp

Energy Energy Class: A

Washing Performance Class: A

Spin Efficiency Class: B

Energy Consumption 1.33 kWh / Cycle @ 60°C Cotton

Water Consumption 52 Litres @ 60°C Cotton

Wash Load 7.0 kg Cottons

Spin Speed All models - 1200rpm

Water Supply Cold Valve - Coil Resistance 3.8 KΩ

Max Pressure = 1 Mpa (10bar)

Minimum Pressure = 0.05 Mpa (0.5bar)

Wash Heater 1700 Watts @ 230 volts Resistance 30 Ω approx.

Thermistor NTC Resistance: 20 KΩ@ 20°C

Pump 2 Pole Synchronous

220 / 240 Volt 25 Watt, Resistance = 162 Ω

Door Lock P.T.C. Solenoid with emergency door release

Module EVOII - WMF720PUK.R

WMF720GUK.R

Arcadia - WMF720PUK.RA

WMF720GUK.RA

Dimensions Height 850 mm Width 595 mm

Depth 565 mm Weight 61 kg Packed approx. 62.9 kg

5 of 30

Indesit Company

Service Manual UK English

INSTALLATION

Unpacking

1. Unpack the washing machine and check whether the it has been damaged during transport.

If this is the case, do not install it and contact the retailer.

2. Remove the two (UK built) or four (Polish built models) protective screws (transit bolts) and the

rubber washer with the respective spacer, situated on the rear of the appliance (see Figures below)

3. Fit the blanking plugs provided into the holes vacated by the bolts.

3. Use the plug provided to seal the holes where the mains plug was housed (if supplied), situated on

the lower right hand side on the rear of the appliance.

4. Keep all the removed parts as they will be required again if the washing machine needs to be

moved to another location.

Levelling

1. Install the washing machine on a flat sturdy floor, without resting it up against walls, cabinets etc.

2. Compensate for any unevenness by tightening or loosening the adjustable front feet. The angle of

inclination, measured according to the worktop must not exceed 2°.

Levelling the appliance correctly will provide it with stability and avoid vibrations, noise and shifting

during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow

enough room for ventilation underneath the appliance.

This raised part is attached to the polystyrene base

and should have been removed when unpacking. Remove 4 transit bolts.

6 of 30

Service Manual UK

Indesit

Company

English

Connecting the Water Inlet Hose.

Before making the water

connection to the 3/4"

thread, allow the water

freely from the supply tap

until it is perfectly clear.

Check that seal is in place

inside the hose end cap.

Connect the other end of

the water inlet hose to the

washing machine,

screwing it onto the cold

waterinlet,situatedonthe

top right-hand rear of the

appliance - see

illustration.

!Screw the inlet end with the blue cap onto the cold water supply tap.

Turn the tap on and check for leaks: tighten if necessary.

Make sure there are no kinks or bends in the hose.

The water pressure at the tap must be within the values indicated in the

Specifications page.

7 of 30

Indesit Company

Service Manual UK English

DRAINAGE CONNECTIONS

A. Connect the drain hose, without kinking it, to a

draining duct or a wall drain fixed at a height

between 65 and 100 cm from the floor. See Fig.1.

B. Alternatively, place it over the edge of a basin, sink

or tub, fastening the hose supplied to the tap.

See Fig.1.

The free end of the hose should not be under water.

Note: We advise against the use of hose

extensions. In case of absolute need, the extension

must have the same diameter as the original hose

and must not exceed 150 cm in length.

Undersink Connections:

The drain hose may be connected to an undersink trap.

Before connecting the drain hose from the machine

ensure that any blanks or removable ends have been

taken off the spigot. See Fig.2.

Note: The hose must also be raised up in a similar way

to a standpipe installation to prevent backflow of waste

water from the sink into the machine. See Fig.1.

Electrical Connections

Before plugging the appliance into the mains socket, make sure that:

- the socket is earthed and in compliance with the applicable law.

- the supply voltage is included within the values indicated in the Specifications page.

- the socket is compatible with the washing machines plug. If this is not the case, replace the socket

or the plug.

Location

! The washing machine should not be installed in an outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.

! When the washing machine is installed, the mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or dangerously compressed.

! The power supply cable must only be replaced by an authorised serviceman.

WARNING!

The company denies all liability if and when these warnings are not respected.

The first wash cycle

Once the appliance has been installed and before you use it for the first time, run a wash cycle

without detergent and no laundry, setting the 90°C programme without a pre-wash cycle.

Fig.1

Fig.2

8 of 30

Service Manual UK

Indesit

Company

English

CONTROLS

DIGIT MODEL (Control panel example shown for information only)

ON-OFF / SELECTING A PROGRAMME

The machine is switched on by pressing the ON-OFF button.

All the indicator lights will light up for a few seconds.

Turn the programme selector dial to the to the desired programme.

Load the laundry and detergent.

Select the Option you require, a time will be indicated in the display window.

Press the Start / Cancel button.

A beep will be heard followed by a CLUNK from the door lock Solenoid as it locks the door, at this

stage the door locked indicator symbol will light.

On-Off

Programme Selector Dial Variable Progress Indicator Lights

Door Locked

Symbol

Option Buttons Start/Pause

Child Lock

Controls Digital

Display

9 of 30

Indesit Company

Service Manual UK English

TO STOP OR CHANGE A PROGRAMME

Press the ON-OFF button for approximately 3 seconds

Select PUMP OUT on the programme dial.

Switch on and re-start

When the machine has finished emptying.

Press the ON-OFF button

Select a new programme and re-start

NOTE: If you cancel a HOT wash programme, take care when removing the laundry, it may still be

VERY HOT.

PROGRESS INDICATOR LIGHTS

These lights will light up when you choose a programme, to indicate the progress of the selected

programme.

When started, the first light in the cycle will stay lit and as the programme progresses, successive lights

will come on until the programme finishes.

DOOR LOCKED INDICATOR LIGHT

The 'Door Locked' indicator light will come on when you press the START / PAUSE button and will stay

lit throughout the programme. When the programme has finished the indicator light will go out and you

can then open the door, a double CLUNK noise will be heard from the door lock Solenoid at this point.

If the door is not closed properly prior to starting a programme the door lock solenoid will 'CLUNK'

approximately 5 times followed by a flashing DOOR indication in the display window, every 5 seconds

from then onwards there will be an audible beep.

Push the door closed and press START / PAUSE button to commence the cycle.

CHILD LOCK

To set the Child Lock, start the programme required then press and hold the Child Lock button for

2 seconds. At this point a red LED will illuminate on the button - Child Lock function is now active.

To Remove Child Lock - Press and hold the Child Lock button down for 2 seconds.

NOTE: - The Child Lock option will need to be removed before another programme can be selected.

10 of 30

Service Manual UK

Indesit

Company

English

OPTIONS

Options are selected by pressing the button and confirmed by illumination an orange LED situated in

the button.

If an option is not available with a programme, the LED will flash and a bleeping noise will be heard

when pressing the button.

Delay Start

To set a delayed start for the selected wash cycle, press the button repeatedly until the desired delay

time is displayed [this may be between 1 hour and 24 hours].

To disable the function press the button until the text OFF is displayed.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you

wish to modify it. This option is enabled with all programmes.

Mini Load

This function is recommended for when the load of laundry is equal to half, or less than half, of the

maximum recommended load [see Table of wash cycles].

This function may not be used in conjunction with wash cycles 5, 11, 12, 13, B, C.

Reduced Creases

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of

creases. At the end of the cycle the washing machine will perform slow rotations of the drum; the

REDUCED CREASES and START/PAUSE indicator lights will flash [orange] and the END phase will

remain lit in a fixed manner. To end the cycle, press the START/PAUSE button or the REDUCED

CREASES button.

For the Silk [10] and Lingerie [B] wash cycles, the machine will end the cycle while the laundry is

soaking, the REDUCED CREASES and START/PAUSE indicator lights will flash [orange] and the

RINSE phase will remain lit in a fixed manner. To drain the water so that the laundry may be removed,

press the START/PAUSE button or the REDUCED CREASES button.

This function may not be used in conjunction with wash cycles 6, 9, 11, 12, 13, B, C.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the

increased cycle duration, this function offers a high-performance wash.

This function may not be used in conjunction with wash cycles 5, 8, 9, 10, 11, 12, 13, A, B, C.

DELAY START

MINI LOAD

REDUCED CREASES

SUPERWASH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hotpoint Waschmaschine Handbücher

Hotpoint

Hotpoint WMEF 762 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Beko

Beko WMB 61031 M Bedienungsanleitung

LG FH695BDH0N Bedienungsanleitung

Indesit

Indesit XWA 61251 Bedienungsanleitung

Bosch

Bosch WAT2878XZA Technisches Datenblatt

NEFF

NEFF W7 Bedienungsanleitung

Amica

Amica AWN614D Bedienungsanleitung

Beko

Beko WMY 81233 LMB3 Bedienungsanleitung

Beko

Beko WMB 71442 LMA Bedienungsanleitung

LG WM3170CW Bedienungsanleitung

Beko

Beko WTV 7832 X00 Bedienungsanleitung

Beko

Beko WMB 81442 LW Bedienungsanleitung

Beko

Beko WMB 61021 MS Bedienungsanleitung

Indesit

Indesit IWE 61051 Bedienungsanleitung

Beko

Beko WMP601W Bedienungsanleitung

LG WT1201CV Bedienungsanleitung

AEG

AEG L 76285 FL Bedienungsanleitung

Beko

Beko WMB81241LS Bedienungsanleitung

arcelik

arcelik 9123 HE Bedienungsanleitung