2.8 CONFIGURATION OF THE RADAR SENSOR UNIT
SETTINGS WITH BUTTONS
LED green/red
IR-receiver
IR-transmitter
Button MENU
Button VALUE
Programming mode
The programming mode allows to adjust the radar sensor unit with two push buttons. All settings can be read out the below programming table.
The LED flashing order shows the respective settings.
While the programming mode is activated the IR-communication is blocked but the sensor functions are still active.
If during 10 minutes no settings have been done the programming mode will be quitted and all settings will be saved automatically.
START: Activate programming mode
Push button MENU for approx. 2s, programming mode is activated LED is flashing. The flashing order shows the actual settings.
LED flashing red number corresponding MENU nr. LED flashing green number corresponding VALUE nr.
the LED does not flash if the VALUE is = 0
STOP: Leave programming mode
Push button MENU for approx. 2s, programming mode is quitted all settings are automatically saved
Set MENU or VALUE →watch programming table
push button MENU 1x short = increase MENU 1 step
Is the maximum menu nr. reached, the programming starts again with the lowest menu nr., i.e. 1x push = 1 step forwards
push button VALUE 1x short = increase VALUE 1 step
Is the maximum value reached, the programming starts again with the lowest value, i.e. 1x push = 1 step forwards
When the MENU or VALUE buttons be pushed, the flashing code stops and restarts flashing with the new value.
After each change the setting will be automatically saved.
Programming sample: Change the output hold time from 1.0 s to 3.0 s
push button MENU approx. 2s = start programming
LED flashing 1x red and 8x green = MENU sensitivity, VALUE 8
push button MENU 3x
LED flashing 4x red and 3x green = output hold time VALUE 1.0 s
push button VALUE 3x
LED flashing 4x red and 6x green = output hold time VALUE 3.0 s
push button MENU approx. 2s = stop programming, setting automatically saved
Programming table
MENU
red LED
flashing according no
e.g. 3x red = vehicle
detection
VALUE
green LED
flashing according value
0 = LED not flashing!
DESCRIPTION
Start: push button MENU for approx. 2s
Stop: push button MENU for approx. 2s
Reset: push button MENU and VALUE at the same time for approx. 2s
LED flashing for approx. 10s green/red
1
Sensitivity 1 - 16 1 = lowest sensitivity = small detection area
16 = highest sensitivity = big detection area
2
Detection mode
0
1
2
3
off
stereo forwards
stereo backwards
mono
off = no detection possible
detects motion towards the radar sensor unit
detects motion away from the radar sensor unit
detects motion forwards and backwards
3
Vehicle detection
0
1
2
3
off
low
medium
high
off = no detection the vehicle relays does not switch
only vehicles will be detected
the settings low, medium and high allow to set the sensor accurate according to the localization
4
Output hold time
0
1
2
3
4
5
6
7
8
off
0.2s
0.5s
1.0s
1.5s
2.0s
3.0s
4.0s
5.0s
off = relay does not switch
0.2s = smallest hold time
1.0s = factory setting
5.0s = biggest hold time
5
Relay contact
1
2
N.O.
N.C.
contact will close by detection detection mode switched off and the change of relay contact
contact will open by detection will keep the gate constant open or closed
6
Fade out cross traffic
0
1
2
3
off
low
medium
high
all movements well be detected
cross traffic will be fade out
the settings low, medium and high allow to set the sensor accurate according to the localization
7
Sensor address 1 – 16
The sensor address is needed for the programming with remote control. The address can be
choose and changed with buttons. The sensor address must be changed only if there are more
than one sensor inside the range of the remote control.
