Howard MWP2 Bedienungsanleitung
Keep tightly closed when in operation
not exceed the rated operating temperature of the fixture.
Do not install in a hazardous atmosphere, except where the ambient temperature does
Make sure the supply voltage is the same as the rated voltage of the luminaire.
Make sure LEDs and drivers are cool to touch when performing maintenance.
Minimum size 18 AWG or 14 AWG for continuous runs.
Use only UL (or other NTRL) approved wire for input/output connections.
Turn off electrical power before inspection, installation or removal.
in accordance with the NEC (National Electric Code) and all local codes.
This product should be installed, inspected, and maintained by a qualified electrician only,
Installation Guide
Read and follow all safety instructions
WARNING
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
Electrical Requirements
Prepare Electrical Wiring
Grounding Instructions
SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
The LED driver must be supplied with the voltage specified on the
product label and connected to an individual, properly grounded branch
circuit protected by a 20 Ampere circuit breaker. Use min. 75°C supply.
The grounding and bonding of the overall system shall be
done in accordance with NEC Article 600 and local codes
LED Lighting Fixture
LED ASSEMBLY
BACKPLATE
FIG.1
MOUNTING:
The back plate has a cast-in drill and knock-out
template to match any standard recessed junction
box, three 5/16” knockouts for mounting holes A and
three 1/2” NPS tapped holes D for surface conduit or
photocontrol unit.
A – 5/16” dia. Knockouts
B – 9/16” dia. Knockouts
C – Knockouts for #10 screw
D – 1/2” NPS tapped holes.
Drill Wire Strippers5/16"
Drill bit Wire Cutters
1/4" Bit Driver Assorted driver bits
Tools Required:
1. Open the fixure by loosening the two (2)
tamper-proof screws on the side of the housing.
2. Disconnect the LED module power leads from
the LED driver and remove the LED assembly. Do
not drop or mishandle the LED assembly.
3. Prepare the back plate for mounting by drilling
or knocking out the appropriate holes. Item A on
Fig. 1.
4. Line up the back plate in the desired location
and mount securely. LED driver assembly may
need to be removed.
5. Apply silicone caulking around the back plate
between the mounting surface for a
weather-tight seal.
6. Reattach the LED driver assebly to the back plate.
7. Wire the fixture leads to the supply leads per Fig. 2 below.
** For EM: Please refer to the wiring diagram on Fig. 3
below. Supply power to the fixture. Connect the battery
plug to the EM. Turn off the wall switch to the fixture.
Installation Guide
8. Reattach the LED module power leads to the driver
and replace the LED assembly using the provided
tamper-proof screws.
9. For EM fixture, press the test button on the side of
the fixture to make sure EM is functioning properly.
Medium Wall Pack, Gen-2
Medium Wall Pack, Gen-2 Installation Guide
Electrical Wiring Diagram - Figure 2
Electrical Wiring Diagram With EM Backup - Figure 3
Andere Howard Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
