HP 64746 Bedienungsanleitung

User’s Guide for the Graphical User Interface

HP 64746

68302 Emulation/Analysis

Notice

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose. Hewlett-Packard shall not be liable for errors

contained herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information, which is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of

Hewlett-Packard Company. The information contained in this document is subject

to change without notice.

HP is a trademark of Hewlett-Packard Company.

Microtec is a registered trademark of Microtec Research Inc.

OSF/Motif and Motif are trademarks of the Open Software Foundation in the U.S.

and other countries.

SunOS, SPARCsystem, OpenWindows, and SunView are trademarks of Sun

Microsystems, Inc.

UNIX is a registered trademark of UNIX System Laboratories Inc. in the U.S.A.

and other countries.

Hewlett-Packard

P.O. Box 2197

1900 Garden of the Gods Road

Colorado Springs, CO 80901-2197, U.S.A.

RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the U.S.

Government is subject to restrictions as set forth in subparagraph (c) (1)(ii) of the

Rights in Technical Data and Computer Software Clause at DFARS 252.227-7013.

Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set forth

in FAR 52.227-19(c)(1,2).

Printing History

New editions are complete revisions of the manual. The date on the title page

changes only when a new edition is published.

A software code may be printed before the date; this indicates the version level of

the software product at the time the manual was issued. Many product updates and

fixes do not require manual changes, and manual corrections may be done without

accompanying product changes. Therefore, do not expect a one-to-one

correspondence between product updates and manual revisions.

Edition 1

Edition 2

Edition 3

64746-97001, August 1990

64746-97003, December 1990

B1469-97000, December 1993

Safety, Certification and Warranty

Safety and certification and warranty information can be found at the end of this

manual on the pages before the back cover.

68302 Emulation and Analysis

The HP 64746 68302 emulator replaces the microprocessor in your embedded

microprocessor system, also called the target system, so that you can control

execution and view or modify processor and target system resources.

The emulator requires an emulation analyzer that captures 64 channels of emulation

processor bus cycle information synchronously with the processor’s clock signal.

The HP 64703 Emulation Bus Analyzer meets this requirement, and it has an

external analyzer that captures up to 16 channels of external data.

You can use the HP 64704 or HP 64794 Emulation Bus Analyzers which have 80

channels; however, these analyzers do not have external analysis channels.

You can also use the HP 64706 Emulation Bus Analyzer which has 48 channels.

Because this analyzer has fewer channels, you cannot capture all the

microprocessor bus cycle information that you can with the other analyzers.

With the Emulator, You Can ...

•Plug into 68302 target systems.

•Download programs into emulation memory or target system RAM.

•Display or modify the contents of processor registers and memory resources.

•Run programs, set up software breakpoints, step through programs, and reset

the emulation processor.

With the Analyzer, You Can ...

•Trigger the analyzer when a particular bus cycle state is captured. States are

stored relative to the trigger state.

•Qualify which states get stored in the trace.

•Prestore certain states that occur before each normal store state.

•Trigger the analyzer after a sequence of up to 8 events have occurred.

•Capture data on signals of interest in the target system with the external

analyzer.

•Cause emulator execution to break when the analyzer finds its trigger condition.

With the HP 64700 Card Cage, You Can ...

•Use the RS-422 capability of the serial port and an RS-422 interface card on

the host computer (HP 98659 for the HP 9000 Series 300) to provide

upload/download rates of up to 230.4K baud.

•Easily upgrade HP 64700 firmware by downloading to flash memory.

With Multiple HP 64700s, You Can ...

•Start and stop up to 16 emulators at the same time (up to 32 if modifications

are made).

•Use the analyzer in one HP 64700 to arm (that is, activate) the analyzers in

other HP 64700 card cages or to cause emulator execution in other HP 64700

card cages to break.

•Use the HP 64700’s BNC connector to trigger an external instrument (for

example, a logic analyzer or oscilloscope) when the analyzer finds its trigger

condition, or you can allow an external instrument to arm the analyzer or break

emulator execution.

With the Graphical User Interface, You Can ...

•Use the emulator and analyzer under an X Window System that supports

OSF/Motif interfaces.

•Enter commands using pull-down or pop-up menus.

•Enter, recall, and edit commands using the command line pushbuttons.

•Enter file names, recalled commands, recalled values, etc., using dialog boxes.

•Set breakpoints by pointing the mouse cursor on a line in the mnemonic

memory display and clicking.

•Create action keys for commonly used commands or command files.

With the Softkey Interface, You Can ...

•Use the emulator and analyzer with a terminal or terminal emulator.

•Quickly enter commands using softkeys, command recall, and command

editing.

In This Book

This book documents the Graphical User Interface and the Softkey Interface when

used with the HP 64746 68302 emulator and the HP 64703/704/706/794 analyzer.

It is organized into five parts whose chapters are described below.

Part 1. Quick Start Guide

Chapter 1 quickly shows you how to use the emulator and analyzer.

Part 2. User’s Guide

Chapter 2 shows you how to start and exit the HP 64700 interfaces.

Chapter 3 shows you how to enter commands.

Chapter 4 shows how to configure the emulator.

Chapter 5 shows how to plug the emulator into a target system.

Chapter 6 shows how to use the emulator.

Chapter 7 shows how to use the analyzer.

Chapter 8 shows how to use the Software Performance Measurement Tool

(SPMT) with the analyzer.

Chapter 9 shows how to use the external state analyzer.

Chapter 10 shows how to make coordinated measurements.

Chapter 11 shows how to change X resource settings for the Graphical User

Interface.

Part 3. Reference

Chapter 12 describes emulator/analyzer interface commands.

Chapter 13 lists the error messages that can occur while using the

emulator/analyzer interface.

Chapter 14 describes emulator specifications and characteristics.

Part 4. Concept Guide

Chapter 15 contains conceptual information on various topics.

Part 5. Installation Guide

Chapter 16 outlines the installation of the Graphical User Interface, and shows

you how to start and exit the interface.

Contents

Part 1 Quick Start Guide

1 Getting Started

The Emulator/Analyzer Interface — At a Glance 24

The Softkey Interface 24

Softkey Interface Conventions 25

The Graphical User Interface 26

Graphical User Interface Conventions 28

The Getting Started Tutorial 31

Step 1. Start the demo 32

Step 2: Display the program in memory 33

Step 3: Run from the transfer address 34

Step 4: Step high-level source lines 35

Step 5: Display the previous mnemonic display 36

Step 6: Run until an address 37

Step 7: Display data values 38

Step 8: Display registers 39

Step 9: Step assembly-level instructions 40

Step 10: Trace the program 41

Step 11: Display memory at an address in a register 43

Step 12: Patch assembly language code 44

Step 13: Exit the emulator/analyzer interface 47

Part 2 User’s Guide

2 Starting and Exiting HP 64700 Interfaces

Starting the Emulator/Analyzer Interface 53

To start the emulator/analyzer interface 53

To start the interface using the default configuration 54

To run a command file on interface startup 55

To display the status of emulators 55

To unlock an interface that was left locked by another user 56

Opening Other HP 64700 Interface Windows 57

To open additional emulator/analyzer windows 57

To open the high-level debugger interface window 58

To open the software performance analyzer (SPA) interface window 58

Exiting HP 64700 Interfaces 59

To close an interface window 59

To exit a debug/emulation session 60

3 Entering Commands

Using Menus, the Entry Buffer, and Action Keys 63

To choose a pulldown menu item using the mouse (method 1) 64

To choose a pulldown menu item using the mouse (method 2) 65

To choose a pulldown menu item using the keyboard 65

To choose popup menu items 67

To place values into the entry buffer using the keyboard 68

To copy-and-paste to the entry buffer 68

To recall entry buffer values 71

To use the entry buffer 71

To copy-and-paste from the entry buffer to the command line entry area 72

To use the action keys 73

To use dialog boxes 73

To access help information 77

Contents

Using the Command Line with the Mouse 78

To turn the command line on or off 78

To enter a command 79

To edit the command line using the command line pushbuttons 80

To edit the command line using the command line popup menu 81

To recall commands 82

To get help about the command line 82

Using the Command Line with the Keyboard 83

To enter multiple commands on one command line 83

To recall commands 84

To edit commands 84

To access on-line help information 85

Using Command Files 86

To start logging commands to a command file 89

To stop logging commands to a command file 89

To playback (execute) a command file 90

Using Pod Commands 91

To display the pod commands screen 92

To use pod commands 92

Forwarding Commands to Other HP 64700 Interfaces 93

To forward commands to the high-level debugger 93

To forward commands to the software performance analyzer 94

4 Configuring the Emulator

Using the Configuration Interface 99

To start the configuration interface 100

To modify a configuration section 102

To store a configuration 104

To change the configuration directory context 105

To display the configuration context 106

To access help information 106

To exit the configuration interface 107

To load a configuration 107

Contents

Modifying the General Configuration Items 108

To select the emulator clock source 108

To enable/disable entry into the monitor after configuration 109

To restrict the emulator to real-time runs 110

To turn OFF the restriction to real-time runs 111

To select the inverse assembly syntax 111

Selecting the Emulation Monitor Program 112

To use the background monitor program 115

To use a foreground monitor program 116

Mapping Memory 120

To map memory ranges 121

To characterize unmapped ranges 123

To delete memory map ranges 124

To map memory ranges that use function codes 125

Configuring the Emulator Pod 127

To enable/disable bus arbitration 128

To specify the analyzer’s response to bus arbitration 129

To enable/disable emulation memory synchronization 130

To enable/disable /BERR connection to target system 131

To enable/disable response to target system interrupts 132

To select the normal or dedicated interrupt mode 132

To set the reset value for the Supervisor Stack Pointer 133

To set the processor data bus width 134

To specify the target memory access size 134

To select /IACK7 or PB0 135

To drive background cycles to the target system 135

To stop driving background cycles to the target system 136

To specify /DTACK sources for chip selects 137

Setting the Debug/Trace Options 138

To enable/disable breaks on writes to ROM 138

To specify which TRAP instruction is used for software breakpoints 139

To include/exclude background states in the trace 140

Contents

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Computerhardware Handbücher

HP Xw460c - ProLiant - Blade Workstation Bedienungsanleitung

HP MCS G2 Installationsanleitung

HP 10512 Montageanleitung

HP QMH2672 Bedienungsanleitung

HP JG560A Bedienungsanleitung

HP Adaptec ultra p2280a Bedienungsanleitung

HP Kayak XW U3-W3 Bedienungsanleitung

HP 3000 Series Handbuch

HP 6600 FIP-20 Flex Montageanleitung

HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

HP C-CLASS BLADESYSTEM 409513-B21 Gebrauchsanweisung

HP Xw8400 - Workstation - 4 GB RAM Bedienungsanleitung

HP Visualize c100 Bedienungsanleitung

HP Model 744 - VME Workstation Bedienungsanleitung

HP UNDP-1H Bedienungsanleitung

HP F768WM Bedienungsanleitung

HP Kayak XU04 Bedienerhandbuch

HP StoreOnce 2700 Bedienerhandbuch

HP rp7420 Bedienungsanleitung

HP Z400 - Workstation Bedienungsanleitung

HP Vectra VE4 Bedienungsanleitung

HP E5000 Bedienungsanleitung

HP t730 Thin Client Bedienungsanleitung

HP Xw4600 - Workstation - 2 GB RAM Merkblatt

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung