HP Cluster Platform Hardware Kits v2010 Montageanleitung

Andere Handbücher für Cluster Platform Hardware Kits v2010

8

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere HP Server Handbücher

HP

HP Integrity Superdome SX1000 Bedienungsanleitung

HP

HP ProLiant SL4540 Handbuch

HP

HP LC2000r - NetServer - 128 MB RAM Bedienungsanleitung

HP

HP rp8400 Series Bedienungsanleitung

HP

HP P2000 G3 Bedienungsanleitung

HP

HP ProCurve 745wl Montageanleitung

HP

HP D7171A - NetServer - LPr Bedienungsanleitung

HP

HP Integrity rx6600 Bedienerhandbuch

HP

HP 780019-S01 Handbuch

HP

HP A4500A - VMEbus Single Board Computer 744... Bedienungsanleitung

HP

HP Hyper Converged 380 Bedienungsanleitung

HP

HP DW017B - StorageWorks Ultrium 448 Tape Drive Bedienungsanleitung

HP

HP D7171A - NetServer - LPr Service-Handbuch

HP

HP NetServer LH 3r Bedienungsanleitung

HP

HP ML530 - ProLiant - 128 MB RAM Bedienungs- und Sicherheitshinweise

HP

HP ProLiant DL560 Gen10 Bedienungsanleitung

HP

HP LC2000r - NetServer - 128 MB RAM Bedienungsanleitung

HP

HP ProLiant DL360 G9 Kurzanleitung

HP

HP Apollo 2000 System Handbuch

HP

HP ProLiant MicroServer Gen8 Bedienungsanleitung

HP

HP ProLiant DL180 Gen9 Bedienungsanleitung

HP

HP ProLiant DL360 Generation 7 (G7) Gebrauchsanweisung

HP

HP HPE ProLiant ML30 Gen9 Handbuch

HP

HP ProLiant ML350e Gen8 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Dell

Dell PowerEdge HS5610 Handbuch

1

Rail Mounting Kit Installation Instructions

for the ProCurve Series zl Switches

The zl switches can be mounted with the optional Rail Mounting Kit (5070-0145) for shipment in an

HP 10000 series rack. These rails stabilize the switch, so the rack or cabinet can be shipped without

removing the switch. However, the power supplies must be removed from the chassis before shipping.

Note

The power supplies must be removed from the chassis before shipping in a rack.

Even though the illustrations show a Switch 5406zl, the instructions apply to all zl chassis models.

1. Use a posi-drive screwdriver, two included 8-mm M6 screws, and two included M6 cage nuts to

attach each rail to the rack or cabinet as shown in the following illustration. Ensure that the

screws are at the same level in each upright.

Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest

device at the bottom and progressively lighter devices installed above.

Figure 1. Attaching Rails to a Rack

8 mm

M6 screw

2

2. Use a #1 Phillips (cross-head) screwdriver and two included 8-mm M4 flat head screws to attach

a hold-down bracket to the chassis as shown in the following illustration. Ensure that each hold-

down bracket is positioned at the lower rear corners of the chassis.

Figure 2. Attaching Hold-Down Bracket

8 mm

M4 screws

Hold down

bracket

3

3. Use a #1 Phillips (cross-head) screwdriver to attach the mounting brackets to the switch with

the included 8-mm M4 screws. Each bracket is attached with four screws as shown in figure 3.

Figure 3. Attaching Rack Mounting Brackets

4. Slide the switch onto the rails in the rack until the mounting brackets are flush with the front

of the cabinet.

Figure 4. Notches in Bracket Being Installed

8 mm

M4 screws

Mounting

bracket

4

5. Install the four number 12-24 screws (included in the mounting bracket kit) into the upper and

lower holes in each bracket. Tighten these screws.

Figure 5. Installing screws in brackets

install and tighten the

other 12-24 screws

© Copyright 2006, 2007 Hewlett-Packard

Development Company, LP. All rights reserved.

The information contained herein is subject to

change without notice.

This document contains proprietary information,

which is protected by copyright. No part of this

document may be photocopied, reproduced, or

translated into another language without the

prior written consent of Hewlett-Packard.

Technical information in this document is

subject to change without notice.

Part Number: 5991-8559

August 2007

Printed in Singapore

*5991-8559*