HP Colorado 5GB C4354A Bedienungsanleitung

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 1

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

Installation Guide

HP Colorado 5GB and 8GB Internal Tape Drives

Chapter 1: Getting Started

Viewing the Online User’s Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Running the Install Assistant Program . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 2: Installing the Hardware

Installing the Internal Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

If You Have Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Chapter 3: Installing the Software

Installing the Software for Your Operating System . . . . . . . . . . . . . 16

Installing Colorado Backup for DOS. . . . . . . . . . . . . . . . . . . . . . 17

Installing Colorado Backup for Windows (3.1 or 3.11). . . . . . . . 23

Installing Colorado Backup for Windows 95. . . . . . . . . . . . . . . . 30

Configuring the drive for Windows NT 4.0. . . . . . . . . . . . . . . . . 34

If You Have Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Chapter 4: Using Tapes and Caring for Your Tape Drive

Choosing Tapes for Your Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . 37

Inserting Tapes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Removing Tapes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Caring for Your Tape Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Chapter 5: Technical Information

Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Colorado Backup for DOS Requirements . . . . . . . . . . . . . . . . . . 43

Colorado Backup for Windows Requirements . . . . . . . . . . . . . . 43

Colorado Backup for Windows 95 Requirements . . . . . . . . . . . . 44

Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

LAN Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

What Affects Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Drive Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Chapter 6: Customer Support Services

Support for Your Tape Drive and Colorado Backup Software . . . . . 54

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 2

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

Chapter 1: Getting

Started

This Installation Guide shows you how to:

■Run the Install Assistant

■Install the tape drive in your computer

■Install the software

■Select and use tapes with your drive

When you finish, your tape drive will be ready to make a backup. For

more information, see the online User’s Guide.

Viewing the Online User’s Guide

The Software Installation CD contains a User’s Guide that shows you how

to:

■Use the Colorado Backup software to back up, restore, and verify data

■Recover from a hard drive crash

Windows 95

If the Colorado Backup software has already been installed, from the

Start menu, select Programs, Colorado Backup, User’s Guide to view

the electronic User’s Guide.

You can also view the User’s Guide on the CD. To do this, insert the

Software Installation CD, click on Start, Run, type D:\SETUP (where D: is

your CD-ROM’s drive letter), then click on the User’s Guide button.

Windows 3.1

Insert the Software Installation CD, click on File, Run, type D:\SETUP

(where D: is your CD-ROM’s drive letter), then click on the User’s Guide

button. You will have the option of installing the Acrobat Reader

software if you do not already have it.

Getting Started 3

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 3

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

DOS

If you installed the software from the Software Installation CD, the

online User’s Guide is on your hard drive in the same directory as the

software. If you installed the software from a diskette, the online User’s

Guide is on that diskette. To access the User’s Guide, open the file

DOSGUIDE.TXT with any ASCII text editor.

Running the Install Assistant Program

The Install Assistant program evaluates

your computer system and recommends

the most successful way to attach your

new HP Colorado tape drive.

1. Insert the diskette labeled Run this first!

into your floppy drive.

2. For DOS and Windows 3.1:

Exit to the DOS prompt, type A:\ASSIST

(where A: is the floppy drive letter)

and press ENTER.

For Windows 95 and NT 4.0:

Click the Start button on the task bar,

select Run, type A:\ASSIST

(where A: is the floppy drive letter)

and click on OK.

3. Run the Install Assistant program and select “Recommend...”

4. Print the Install Assistant’s results to provide answers to all the questions

you will encounter during this installation process:

JUMPER

SETTING?

WHICH

IDE

CONTROLLER?

DATA CABLE

INSTRUCTIONS?

ADDITIONAL

IDE CARD

REQUIRED?

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 4

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

Chapter 2: Installing

the Hardware

Installing the Internal Tape Drive

1. Locate the following items before you begin to install the tape drive:

■A medium-size Phillips screwdriver

■Your computer system’s manual (you may need to look up

information about the location of your IDE controllers).

CAUTION: The discharge of static electricity can damage electronic circuitry.

You can avoid static discharge by touching a grounded metal object such as

your computer’s case before and during installation of hardware inside your

computer or by wearing a grounding strap.

2. Make sure you have the items shown below.

Installation Guide

HP Colorado

Software

Screws

OPTIONAL

Data Cable

(you may not

need this)

Install Assistant

Program Diskette

Installation

Tape Drive

Installing the Hardware 5

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 5

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

3. Run the Install Assistant program, if you have not already done so (see

page 3).

4. Remove the Install Assistant diskette.

5. Turn OFF your computer, monitor, and other devices.

Unplug the power cables from the wall outlet or from the power strip, if

you use one. (The power plug and outlet may look different in your

country.)

6. Remove the cover from your computer.

WARNING: Be careful of any sharp edges that may be present inside your

computer.

7. Refer to the printout from the Install Assistant (see page 3). Find the section

labeled ADDITIONAL IDE CARD REQUIRED?

■If NO, skip this step.

■If YES, follow the directions in the HP Colorado IDE Adapter Card

Installation Guide before continuing (contact your local vendor to

purchase the card).

See your computer’s

manual if you need help

removing the cover.

Computer OFF

6Installation Guide

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 6

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

8. Do you want to install the tape drive in a larger “half-height” drive bay or

a smaller “1-inch” drive bay?

Remove the cover plate from the desired drive bay.

TIP: Keep any mounting hardware such as rails. You will need this

hardware for securing the drive in step 11.

9. If you are installing the tape drive in a larger “half-height” drive bay, skip

this step.

If you are installing the tape

drive in the smaller “1-inch”

drive bay, remove and discard

the mounting bracket from

the tape drive.

The smaller drive bay

configuration (without

mounting brackets) is

illustrated in the remaining

steps of this guide.

Available half-height drive bay

Available 1-inch drive bay

See your computer’s

manual if you need help

removing the drive bay cover.

(approx. 6” x 1.75”/15cm x 4.5 cm)

(approx. 3.5” x 1”/8.9 cm x 2.54 cm)

Mounting

Bracket

Tape drive

Installing the Hardware 7

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 7

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

10. Refer to the printout from the Install Assistant (see page 3). Find the section

labeled JUMPER SETTING? Set the jumper as advised.

TIP: You can use needle-nose pliers

if you need to move the jumper.

Slave

Check the back of your tape drive and

make sure the jumper is on the center

location (Slave-SL).

or Master

Check the back of your tape drive and

make sure the jumper is on the right-

hand location (Master-MA).

Don’t use

CS (Cable Select)

Don’t use

CS (Cable Select)

Green circuit

board is the top

of the drive

This is a jumper.

Back view of the tape drive

8Installation Guide

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 8

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

11. Insert the drive into the drive bay. Be careful not to dislodge any cables

inside your computer as you do this.

WARNING: The drive requires a secure fit. If there is a gap of 1/8 inch (3.2

mm) or more on either side of the drive, you will not be able to secure it. In this

case, obtain and attach “rails” from your computer manufacturer BEFORE

inserting the tape drive. (You may already have what you need from step 8.)

12. If there is not much room around the back of the tape drive, it may be

better to wait until step 17 to complete this step.

Secure the drive into the bay, using the screws included:

■if installing in the large drive bay, use the silver screws

(#6-32 x 1/4” screws).

■if installing in the small drive bay, use the black screws

(M3x0.5 x 6 mm metric screws).

The screws electrically ground the tape drive.

Use all four screws

Installing the Hardware 9

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 9

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

13. Refer to the printout from the Install Assistant (see page 3). Find the section

labeled WHICH IDE CONTROLLER?

TIP: If the Install Assistant stated that your tape drive will share the

data cable with another device (such as your CD-ROM), simply follow

the cable already attached to that device down to the circuit board in

order to locate the IDE controller that you need. If you find an extra

connector along that cable, in the next step, simply attach the tape

drive to that cable. Go to step 14 now.

Inside your computer, you may find up to five IDE controllers. Locate the

40-pin IDE controller that will be used by the tape drive as indicated by

the Install Assistant:

■The first two IDE controllers (Primary and Secondary) are usually on

the mother board of the computer.

■The third, fourth, or fifth IDE controller may be located on an

expansion card or sound board and may not be labeled.

See your computer’s

manual if you need

Computer manufacturers use a wide variety of

labels for IDE controllers! Look on your

computer’s circuit boards for tiny printing such

as:

- PRI and SEC (for primary IDE and secondary IDE)

- IDE-0 and IDE-1

- IDE-1 and IDE-2

- HD and CD-ROM (most common devices to be attached)

- PCI-IDE and ISA-IDE

You will see a variety of connectors inside

your computer that look similar to the 40-

pin connector but have more or less pins.

Find the connectors that are the correct

size to fit the cable that came in the

box with your drive.

IDE Controllers

help finding the

Not shown actual size.

IDE Controllers

IDE Controller.

10 Installation Guide

G:\TW\Lori\Raptor\C4386-90100\c4386-90100.fm5 Page 10

Last Modified: Tuesday, January 27, 1998 8:17 pm

Printing date: Saturday, April 04, 1998

14. Refer to the printout from the Install Assistant (see page 3). Find the section

labeled DATA CABLE INSTRUCTIONS?

Follow the instructions on the next page for either “One Device” or “Two

Devices” as advised.

TIP: If you are sharing the IDE data cable between the HP tape drive and

another device, when the HP tape drive is configured as “Slave” the other

device must be configured as “Master.” Similarly, if the HP tape drive is

configured as “Master” the other device must be configured as “Slave.”

CAUTION: Make sure that you are attaching the cable correctly! You must

locate PIN-1 on each connector and attach the cable so that the edge with the

color stripe is aligned with PIN-1. If the cable is attached incorrectly, your

computer may not boot up.

PIN-1

The cable’s colored edge is aligned

with PIN-1 of the IDE connector.

colored stripe on

the data cable

PIN-1

The cable’s colored edge is aligned

with PIN-1 on the tape drive.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP P9000 Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP 157770-001 - DAT Drive 20/40 Tape Bedienungsanleitung

HP Compaq Pro 6305 Bedienungsanleitung

HP StoreOnce B6000 Betriebsanleitung

HP StorageWorks NAS 8000 - Version 1.6.X Bedienungsanleitung

HP StoreEver ESL G3 Bedienungsanleitung

HP Pavilion p6000 - Desktop PC Bedienungsanleitung

HP Surestore 64 - Director Switch Bedienungsanleitung

HP P2000 G3 Kurzanleitung

HP D2D Bedienerhandbuch

HP StorageWorks ESL E-Series Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Service-Handbuch

HP HP 7936 Montageanleitung

HP StorageWorks XP12000 Bedienungsanleitung

HP Colorado 5GB Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP StoreOnce D2D Backup System Gen2E Handbuch

HP C1593B - SureStore DAT Tape 5000e Drive Bedienungsanleitung

HP StorageWorks 4400 Bedienungsanleitung

HP 330834-B21 - StorageWorks Ultrium 460 Tape Library Drive... Produkthandbuch

HP StorageWorks 8B - FC Entry Switch Bedienungsanleitung

HP StoreOnce 4900 Backup Bedienerhandbuch

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung