HP D7171A - NetServer - LPr Bedienungsanleitung
HP Ultra/Wide SCSI 4 GB and
9 GB Hard Disk Drive
Installation
G
uide
HP Part Number 5967-4544
Printed in June 1998
ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced, or
translated to another language without the prior written consent of Hewlett-
Packard Company.
NetWare®and UnixWare®are registered trademarks of Novell, Inc. Microsoft®
Windows NT and NTAS®are registered trademarks of Microsoft Corporation.
SCO®UNIX®is a registered trademark of The Santa Cruz Operation, Inc.
Banyan®and VINES®are the registered trademark of Banyan Systems
Incorporated. OS/2is the registered trademark of the International Business
Machines Corporation.
Hewlett-Packard Company
Network Server Division
Technical Marketing/MS 49EU-FQ
5301 Stevens Creek Blvd.
P. O. Box 58059
Santa Clara, CA 95052-8059 USA
© Copyright 1998, Hewlett-Packard Company.
Audience Assumptions
This guide is for the person who installs, administers, and troubleshoots LAN
servers. Hewlett-Packard Company assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with
hazardous energy levels.
iii
Contents
1 Prepare Drive for Installation..........................................................................1
Introduction........................................................................................................1
General Installation Steps .............................................................................1
Step 1: Prepare for Installation..........................................................................2
Tools You Need.............................................................................................2
Setup Information You Need.........................................................................2
Unpack the Drive...........................................................................................3
Step 2: Determine the Drive Type .....................................................................3
Step 3: Set the SCSI Address ...........................................................................8
Step 4: Connect SCSI Cable Adapter (if required)..........................................14
Step 5: Continue Installation............................................................................14
2 Mount the Drive in the NetServer L Series.................................................. 15
Step 1: Mount the Drive in the System ............................................................15
Step 2: Connect the Drive Activity Light...........................................................16
Step 3: Connect the Drive................................................................................19
Step 4: Configure the Drive .............................................................................20
3 Mount the Drive in the NetServer E 45......................................................... 23
Step 1: Determine the Drive Location..............................................................23
Step 2: Mount the Drive in the System ............................................................25
Mount the Drive in Shelf 5 or 6....................................................................25
Mount the Drive in Shelf 3 or 4....................................................................26
Step 3: Connect the Drive................................................................................26
Step 4: Configure the Drive .............................................................................27
A Jumper Settings ............................................................................................ 29
Jumper Legend................................................................................................29
B Disk Drive Characteristics............................................................................ 31
NetWare and DOS...........................................................................................31
OS/2 and Windows NT....................................................................................32
UNIX and Banyan Vines..................................................................................33
C Returning HP Hard Disk Drives....................................................................35
D Warranty and Support...................................................................................37
Hardware Warranty..........................................................................................37
Contents
iv
HP Repair and Telephone Support.................................................................. 37
E Regulatory Information................................................................................. 39
Index.................................................................................................................... 41
1
1 Prepare Drive for Installation
Introduction
This chapter describes the tools, setup information and the steps necessary to
install a SCSI hard disk drive into an HP NetServer. The drives documented in this
guide are listed in Table 1-1.
Table 1-1. Hard Disk Drive Product Numbers
HP Product Number Capacity1
D4910A 4.26 GB
D4911A 9.10 GB
General Installation Steps
In general, the steps for installing a hard drive are shown below. Please refer to the
detailed instructions in each step before attempting to install your drive.
1. Prepare for Installation
2. Determine the Drive Type
3. Set the SCSI Address
4. Connect SCSI Cable Adapter (if required)
5. Mount the Drive in the System
6. Connect the Drive Activity Light (if appropriate)
7. Connect the Drive
8. Configure the Drive
CAUTION In a few cases, drives with the same product number can be of
different types and require different jumper settings. If your
drive does not match the type in the figure, check the other
figures for the matching type.
1The operating system may report a different capacity.
Chapter 1 Prepare Drive for Installation
2
Step 1: Prepare for Installation
Gather the tools and the setup information you need to install the drive, before
removing the drive from its packaging.
Tools You Need
To install the disk drive, you need the following tools:
•Tweezers, needle-nose pliers or a similar tool for setting configuration
jumpers.
•A TorxTM T-15 screwdriver or a regular blade screwdriver.
Setup Information You Need
Before you begin, you need the following setup information:
•The HP NetServer Installation Road Map for your system or Information
Assistant on the HP NetServer Navigator CD-ROM.
•The SCSI addresses available in your system. (Refer to your system in
Information Assistant on the HP NetServer Navigator CD-ROM for
information on determining available SCSI addresses.)
Chapter 1 Prepare Drive for Installation
3
Unpack the Drive
CAUTION Shock: Hard disk drives are very susceptible to mechanical
shock and can be damaged by a drop as short as one-quarter of
an inch. Take care when unpacking and handling the disk
drive. If the drop would crack an egg, it will damage the drive.
Static: Protect the hard disk drive from static electricity by
leaving it in its anti-static bag until you are ready to install it.
Use an antistatic wrist strap and a grounding mat (3M
8501/8502/8505 or equivalent). If an antistatic work area is
not available, touch any unpainted metal surface to discharge
static electricity before handling the drive.
When you remove the hard disk drive from the anti-static bag,
handle it only by the frame. Do not touch the electrical
components. Place the drive on the anti-static bag whenever
you set it down.
After gathering the information and tools:
•Remove the drive from the packaging.
Step 2: Determine the Drive Type
The type of the drive varies and drives with the same part number may be of
different types.
•Match the drive you unpacked with the type of drive shown in Figure 1-1.
Chapter 1 Prepare Drive for Installation
4
D4910A 4.26 GB Model
(Type 1)
D4910A 4.26 GB Model
(Type 2)
D4911A 9.10 GB Model
(Type 2)
D4911A 9.10 GB Model
(Type 3)
D4910A 4.26 GB Model
(Type 5)
D4910A 4.26 GB Model
(Type 4) D4911A 9.10 GB Model
(Type 4)
D4911A 9.10 GB Model
(Type 5)
Figure 1-1. Identification of the 4 Different Types of Drives
Chapter 1 Prepare Drive for Installation
5
NOTE Some of the product numbers are duplicated, because the type
of drive shipped is not always the same. Therefore, it is
important that you match your drive to the correct type.
The types of drives differ in that the jumpers are in different locations. Refer to the
appropriate illustration (Figure 1-2, 1-3, 1-4, 1-5 or 1-6) for your type of drive,
and note the location of the jumpers.
The "Disk Drive Characteristics" appendix shows a legend of the drive control
settings and the jumper control settings for the individual drives.
J2
J6
Power Connector
J1
SCSI Connector
Figure 1-2. Component Identification, Type 1 Drives
Chapter 1 Prepare Drive for Installation
6
J4
Power
Connector
SCSI
Connector
Figure 1-3. Component Identification, Type 2 Drives
J2
J6
Power Connector
SCSI
Connector
Figure 1-4. Component Identification, Type 3 Drives
Andere Handbücher für D7171A - NetServer - LPr
117
Dieses Handbuch passt für folgende Modelle
6
Inhaltsverzeichnis
Andere HP Lagerung Handbücher
HP
HP StorageWorks XP10000 - Disk Array Bedienungsanleitung
HP
HP D2200sb Gebrauchsanweisung
HP
HP HPE StoreOnce 3100 Series Handbuch
HP
HP J3278B - SureStore CD-ROM Server/Tower 7 NAS... Service-Handbuch
HP
HP StorageWorks 500 Generation 2 Handbuch
HP
HP Performance Optimized Datacenter 20c Handbuch
HP
HP Surestore XP256 - Disk Array Bedienungsanleitung
HP
HP StorageWorks DAT 72 Bedienungsanleitung
HP
HP StorageWorks Ultrium 215 Gebrauchsanweisung
HP
HP StorageWorks XP10000 - Disk Array Bedienungsanleitung
HP
HP SureStore DAT40e Bedienungsanleitung
HP
HP C737990900 Produkthandbuch
HP
HP StorageWorks NAS b2000 - v2 Bedienungsanleitung
HP
HP D2D Bedienungsanleitung
HP
HP Portable Hard Drive Bedienungsanleitung
HP
HP Xw4550 - Workstation - 2 GB RAM Bedienungsanleitung
HP
HP StorageWorks XP10000 - Disk Array Bedienungsanleitung
HP
HP 7942 Bedienungsanleitung
HP
HP HPE StoreEver LTO-8 Ultrium Tape Produkthandbuch
HP
HP StorageWorks NAS 8000 - Version 1.6.X Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
LaCie
LaCie RUGGED MINI Bedienungsanleitung
Thunderbolt
Thunderbolt 600 Bedienungsanleitung
Panasonic
Panasonic LB-DH8 series Handbuch
Intel
Intel RAID High Availability Bedienungsanleitung
LaCie
LaCie 12big Thunderbolt 3 Bedienungsanleitung
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung
Dell
Dell PowerVault MD3600f Series Bedienungsanleitung
CFI
CFI TERA STOR SATA RAID IV Bedienungsanleitung