HP StorageWorks 7100 - Virtual Array Kurzanleitung

Replacement Procedure: VA7.x Disk Module, 18GB-36GB-72GB

You can add or replace disks to increase storage capacity or eliminate faults. (See Chapter 3 of the

HP StorageWorks Virtual Arrays VA 7000 Family User’s and Service Guide for troubleshooting procedures.)

Disks must be Fibre Channel (FC) and 3.5 inches wide but can vary in capacity.

For current information about supported disks, consult an HP sales representative.

You do not need to turn off the array to replace a disk or filler.

Caution Do not remove hot-pluggable components until you have the

replacement parts and are ready to install them. An empty slot will cause

uneven cooling and eventual overheating.

Caution Parts can be damaged by electrostatic discharge. Please ensure

that ESD measures are in place.

Step 1

Open the Disk Replacement Kit and inspect the contents per the first step of the Disk Replacement Sheet

included with the replacement drive.

Step 2

Caution Touching exposed electrical circuitry on the disk can damage the disk. Be sure you are grounded

and be careful not to touch exposed circuits.

Disk modules are fragile and ESD sensitive. Dropping one end of the disk just two inches is enough to cause

permanent damage. In addition, static electricity can damage the disc. Grasp disks only by their handles (A

in Figure 1) and carriers (D), and follow strict ESD procedures.

Figure 1: Disk Module Installation

A extraction handle

C LEDs

B cam latch D carrier

Step 3

Push down release tab (B in Figure 1), pull up the lever (A) on disk to be replaced.

Step 4

Caution Wait 15 seconds for the disk to spin down. There is a danger of damage to the disk if it is dropped

due to gyroscopic effects. Wait for a spinning disk to stop spinning prior to removing it from the product.

Step 5

Pull the disk to be replaced from the slot.

Step 6

Caution DO NOT leave the disk slot empty for more than 5 minutes, as proper cooling/airflow depends on

all slots being full.

Step 7

Verify that the disk module extraction handle (A in Figure 1) is open . Place your thumb behind the

extraction handle and with your finger, push the latch tab (B) toward your thumb.

Note It is important that the new disk is of the same capacity (in GB) or larger than the disk being replaced.

Step 8

Push the replacement disk module, capacity label up, into the empty slot.

Step 9

Push down the lever (A in Figure 1) on the disk. It will click into place.

Step 10

The drive will now begin an automatic formatting process. Depending on your system configuration, the time

to complete will vary.

Note An exchange disk drive comes formatted with 512-byte sectors. After installation, the controller starts

the Auto Format process to automatically format the disk drive with 520-byte sectors. Table 1 indicates the

times required for formatting the different capacity disks.

Note Depending on the total amount of memory in your array and your specific configuration, a complete

format and rebuild process may take between 4 and 24 hours. As per Step 11 (below) monitor your array for

correct LED behavior.

Table 1: Raw format Times (Verify Off)

Disk

Capacity Format Time

(Minutes)

18 GB 15k 8

36 GB 10k 20

73 GB 10k 28

Caution To prevent corruption of the disk format, do not remove a newly installed disk drive or power-off the

array during the AutoFormat process. If a disk is removed during an Auto Format, the array will automatically

re-start the Auto Format process from the beginning.

Step 11

Monitor the Disk LEDs,

Figure 2: Disk Drive LEDs (Left: VA 71/7400 A/AZ; Right: VA 7100 D)

Note After installation, the controller starts the Auto Format process. During this time, the green disk activity

LED (A in Figure 2) will be flashing. The green (A) LED will also blink with I/O activity to the disk. See Table

2 for a full list of disk LED behaviors. The amber disk fault LED (B) will flash during an Auto Format process.

The amber system fault LED will also flash.

If you observe different results, further Troubleshooting may need to be carried out. (See Chapter 3 of the

HP StorageWorks Virtual Arrays VA 7000 Family User’s and Service Guide for troubleshooting procedures.)

Table 2: Disk Drive LEDs Status Indications

Disk

Activity

(Green*)

Disk Fault

(Amber**)

Indication

Off Off Disk not under power.

On Off Disk drive under power and operating normally.

Off On Disk drive fault.

On On Disk drive fault.

Flashing Off Disk drive self-test in progress or I/O activity.

On/Off Flashing Host is identifying disk drive.

*Controlled by the disk drive.

**Controlled by the array controller.

Procedure Completed!

“Congratulations!”

Andere Handbücher für StorageWorks 7100 - Virtual Array

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP StorageWorks XP1024 Kurzanleitung

HP StorageWorks ESL E-Series Bedienungsanleitung

HP StorageWorks SSL1016 Bedienungsanleitung

HP Compaq Presario,Presario 4400 Leitfaden

HP StorageWorks SB40c Handbuch

HP Storevirtual 4000 Bedienungsanleitung

HP StoreEasy 3830 Bedienungsanleitung

HP LTO Ultrium Produkthandbuch

HP Compaq Presario,Presario 4400 Leitfaden

HP StorageWorks 8B - FC Entry Switch Bedienungsanleitung

HP Data Vault Technisches Datenblatt

HP StorageWorks XP10000 - Disk Array Bedienungsanleitung

HP StorageWorks 8000 - NAS Bedienungsanleitung

HP Xw8200 - Workstation - 1 GB RAM Referenzhandbuch

HP A5272A - SureStore E Disk System SC10 Storage... Bedienungsanleitung

HP StorageWorks 6100 - Enterprise Virtual Array Bedienungsanleitung

HP 9153A Bedienungsanleitung

HP D2D Bedienungsanleitung

HP StorageWorks P4000 Series Bedienungsanleitung

HP StoreOnce 2700 Bedienerhandbuch

HP HP 7936 Montageanleitung

HP StorageWorks Disk System 2405 Gebrauchs- und Pflegehandbuch

HP STOREEVER LTO 4 Bedienungsanleitung

HP StorageWorks 2000fc Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung